APsystems APS2530H User manual

昱能科技
NO.1 Yatai Road, Jiaxing, Zhejiang, China
浙江省嘉兴市南湖区亚太路 1号
[phone] | APsystems.com
User Manual for APS2530H
The model used ZigBee PRO protocol to send RF signals for device communication.
The model can be used after pairing with a dedicated device which was installed with a
receiver dongle.
APS2530H was used as a dongle which need to be installed in customer’s device. It
offers UART to communicate with customer’s device according predefined protocol.
1:product figure(APS2530H)
2: Technical specifications
RF operating frequency: 2402MHz ~ 2483MHz
Reference frequency: 2.400GHz
Channel spacing: 5MHz
Channel wide：2MHz
Modulation method: OQPSK
Communication rate: 250Kbps

昱能科技
NO.1 Yatai Road, Jiaxing, Zhejiang, China
浙江省嘉兴市南湖区亚太路 1号
[phone] | APsystems.com
Output power: 15DBm
Communication mechanism: applied ZigBee frequency hopping mechanism, passively
frequency hopping.
Average operating current：<20mA
Operating voltage：2V-3.6V
Max remitting current: 20mA
Max rate：250Kbit/s
Receiving sensitivity：-95dbm
Receiving current：<24mA
Max receiving distance：>100M
Normal operating receiving distance：100M

昱能科技
NO.1 Yatai Road, Jiaxing, Zhejiang, China
浙江省嘉兴市南湖区亚太路 1号
[phone] | APsystems.com
3. Installation and usage instructions
Installation Notes: users can use SMT or DIP to connect to ZIGBEE module.
It must be ensured that the interface of the module(VCC,GND,RESET,UART) is accurately
connected with the customer's equipment. Make sure the IPEX interface is properly
connected to the antenna.
Instructions for use: Users can interact with the zigbee module through the serial
port. The user uses the serial port to send data to the zigbee module in the specified format,
and the zigbee module will send the data to the specified slave module through the radio
frequency signal.
Pin Descriptions
Pin name
Pin type
Description
P0_0
Digital I/O
Port0.0
P0_1
Digital I/O
Port0.1
P0_2
Digital I/O
Port0.2 - UART RX
P0_3
Digital I/O
Port0.3 - UART TX
P0_4
Digital I/O
Port0.4
P0_5
Digital I/O
Port0.5
P0_6
Digital I/O
Port0.6

昱能科技
NO.1 Yatai Road, Jiaxing, Zhejiang, China
浙江省嘉兴市南湖区亚太路 1号
[phone] | APsystems.com
P0_7
Digital I/O
Port0.7
P1_0
Digital I/O
Port1.0 –20-mA drive capability
P1_1
Digital I/O
Port1.1 –20-mA drive capability
P1_2
Digital I/O
Port1.2
P1_3
Digital I/O
Port1.3
P1_4
Digital I/O
Port1.4
P1_5
Digital I/O
Port1.5
P1_6
Digital I/O
Port1.6
P1_7
Digital I/O
Port1.7
P2_0
Digital I/O
Port2.0
P2_1
Digital I/O
Port2.1
P2_2
Digital I/O
Port2.2
VCC
Power
2-V–3.6-V digital power-supply connection
GND
Ground
Connect to GND
RESET_N
Digital input
Reset, active-low
Package Size
4. Warning
This device complies with Part 15, Subpart C, Section 15.247 of the FCC Rules.
- product should not collocate with other radio
- host label should content modular FCC ID:2AFGR-APS2530H/IC :20481-APS2530H
- ANT type/gain tolerance of antenna OEM should use.
Use only the antenna supplied by the manufacturer when operating this device(antenna
gain:2dBi). Unauthorized antennas, modifications, or attachments, could damage the
device and violate FCC regulations. Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
- Do not disassemble, repair, modify or replace the remote

昱能科技
NO.1 Yatai Road, Jiaxing, Zhejiang, China
浙江省嘉兴市南湖区亚太路 1号
[phone] | APsystems.com
control Unit or any of its components.
EF Radiation Exposure and Hazard Statement:
- To ensure compliance with FCC RF exposure requirement, this device must be installed
in a location such that antenna of the device will b greater than 20cm away from all
persons. Using higher gain antennas and types of antennas not covered under the FCC
certification of this product is not allowed. Installers of the radio and end users of the
product must adhere to installation instructions provided in this manual. This
transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
- Please comply with the national and international flight safety regulations when using device
during your flight trip.
This device complies with part 15 of the FCC Rules. Operationis subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
IC Caution:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage

昱能科技
NO.1 Yatai Road, Jiaxing, Zhejiang, China
浙江省嘉兴市南湖区亚太路 1号
[phone] | APsystems.com
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
RF exposure warning
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux radiations de la IC définies pour un
environnement non contrôlé. Cet équipement doit être installéet utiliséàune distance minimale
de 20 cm entre le radiateur et votre corps.