Aqara E1 User manual

Roller Shade Driver E1 User Manual
Мотор рулонных штор E1: Руководство по
эксплуатации
Bedienungsanleitung für Rollladenmotor E1
Moteur de Volet Roulant E1 Manuel de
l’utilisateur
Manual de instrucciones para el Control de
Cortinas Enrollables E1
Motore per tende a rullo E1 Manuale di
Istruzioni
ローラーシェードドライバーE1ユーザーマニュアル
스마트�블라 E1 사용�설명서
智能捲簾伴侶E1 用戶手冊
·1
·9
·19
·28
·37
·46
·55
·62
·69

Product Introduction
Roller Shade Driver E1 is a Zigbee 3.0 smart product that can
help you control the bead chain of your shades/blinds and
transform your existing roller shade into a smart one. With an
Aqara Zigbee 3.0 hub, it can realize functions such as remote
control and timing control via the Aqara Home app, and work
with other smart devices to form a smart home system.
Warnings
1.This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
2.Children shall not play with the appliance.
3.Cleaning and user maintenance shall not be made by children
without supervision.
4.WARNING: the drive shall be disconnected from its power
source during cleaning, maintenance and when replacing parts.
5.It must only be supplied at Separated or Safety Extra-Low
Voltage (SELV).
6.WARNING: Important safety instructions. It is important for the
safety of persons to follow these instructions. Save these
instructions.
*An Aqara Zigbee 3.0 hub is required. Some functions require specific
models of hubs. Please consult www.aqara.com/support for more details.
RESET
5V
Indicator
Down Button
Up Button
RESET Button USB Type-C Port
1

7.Do not allow children to play with fixed controls.
8.Frequently examine the installation for imbalance and signs
of wear or damage to cables springs and fixings. Do not use if
repair or adjustment is necessary.
9.Do not operate when maintenance, such as window cleaning,
is being carried out in the vicinity.
10.WARNING: Important safety instructions. Follow all
instructions since incorrect installation can lead to severe injury.
11.Before installing the drive, remove any unnecessary cords or
components and disable any equipment not needed for
powered operation.
12.That the characteristics of the driven part must be
compatible with the rated load and rated operating time.
13.This appliance contains batteries that are non-replaceable.
14.Fixed controls have to be clearly visible aer installation.
Preparation before Use
1. A smartphone or tablet that supports Wi-Fi or a cellular
network (with iOS or Android system) is required.
2. An Aqara Zigbee 3.0 hub is required (The distance between
this product and your hub should be within 30 m).
3. Download and install the Aqara Home app.
4. A drilling machine is required (must be equipped with a φ5
drill bit).
5. Please make sure that there is a Wi-Fi connection and your
internet connection is stable.
6. Please charge the Roller Shade Driver E1 for about 2 hours
and 30 minutes.
7. The mass and the dimension of the shade to be driven shall
be compatible with the rated torque and rated operating time.
8. Note: The accessories are only compatible with bead chains
that meet the following standards:
Plastic/metal beads with a thickness of 3-6 mm
2

Device Installation
Scan the QR code below to watch the installation guide.
Choose the installation location.
1
Select the plate according to the following plate-bead
matching relationship, and install it on the output sha of
the device.
2
Hang the bead chain on the plate of the device and pull it
down tightly (not too tight), keep the bead chain tight and hold
the device on the wall, and find a suitable installation location.
3
First, remove the head cover of the device.
Beads with a
diameter of 3 - 4.5
mm (most popular)
Beads with a diameter of 4.5
– 6mm, and beaded cords
with the connector (the
thickness of the connector
should be less than 6mm)
×
√
Please make sure that the bead chain is
put in the selected installation position
properly and does not cross.
3

Attention: do not make the bead too tight
Hold the device in a suitable position, and press the up or
down button of the device to ensure that the bead chain
rotates in a stable manner and does not slip (press the up or
down button again to stop the motor while rotating).
4
Hold the device on the selected installation position, and
outline the shape of the device along its bottom on the wall
with a pencil.
5
Remove the back cover of the device and fix it at the position
about 3-5 mm down from the mark.
Use screws to fix the product. Aer fixing the back cover,
install the device together with the bead chain back on the
back cover.
6
Push the handle to
remove the back cover
5mm
4

Device Binding & Initialization
1. Before activating the accessory, please make sure you have
the Aqara Home app and the Aqara Zigbee 3.0 hub installed.
2. Please open the app, tap “Home” and then tap “+” in the top
right corner to enter the “Add Device (Accessory)” page. Select
“Roller Shade Driver E1” and the hub to be connected to, and
add it according to instructions in the Aqara Home app. Press
and hold the RESET button for 5 seconds, and wait for the
voice prompt from the Hub.
Device Rotating Range Setup
1. Aer the device is connected to the network, you can set the
device rotating range via the Aqara Home app, click the device
card on the homepage of Aqara Home app, and follow the
instructions on the page to set the rotating range;
2. When the device is not connected to the network, the device
rotating range can also be set by pressing the buttons;
Button Operations
Rotating Range Settings
Remove the protection sheet on the head cover, and install the
head cover back on the device. The installation is complete.
7
Delete rotating range
1
Aer the device is installed, press the Up and Down button at
the same time for 3 seconds until the indicator light turns blue,
and then release it.
5

Device control (aer rotating range is set)
Set the fully open position
2
Aer deleting the rotating range, adjust the actual position of
the shade to fully open by pressing the Up or Down button, and
then press the Up button 5 times in succession. If the indicator
light turns blue and flashes 3 times, it indicates that the setting
is successful.
Set the fully closed position
3
Aer setting the fully open position , adjust the actual position
of the curtain to fully closed by pressing the Up or Down button,
and then press the Down button 5 times in succession. If the
indicator light turns blue and flashes 3 times, it indicates that
the setting is successful.
Aer setting the fully open and fully closed positions, the
rotating range setting is complete.
Remap the buttons to rotate the motor in the opposite direction
4
If you press the button of which the direction is opposite to the
actual rolling direction of the roller shade, the rotating direction
of the motor can be reversed by pressing the RESET button
three times; and then, if the indicator turns to blue and lasts for
1 second, it indicates that the rolling direction of the motor is
reversed.
Purpose
Roll the roller
shade
Unroll the
roller shade
Click Up Button - the motor keeps moving
upwards till the shade is fully opened
Click Down Button - the motor keeps moving
downwards till the shade is fully closed
Delete rotating
range
Press and hold the Up button and the Down
button at the same time for three seconds
Reverse motor
rotating direction
Press the RESET button 3 times in a row,
(aer the operation, the blue indicator will
be on for 1 second and then o)
Check network
status
Click the RESET button, if the indicator is
blue, it indicates that it is connected to the
network
Click the RESET button, if the indicator is red,
it indicates that it is not connected to the
network
Stop the roller
shade Roller shade stopped
Operation
6

To charge the device
When the USB cable is plugged in, the indicator will turn to blue
and blink for 3 times.
With the USB cable plugged in, the indicator will turn to red
until the battery is fully charged.
If the battery is fully charged, the indicator will be turned o.
Device Settings
Enter the homepage of the device, click the "..." icon in the
upper right corner to enter the device settings page, where you
can set the timer, automation, roller shade type, etc.
Product Specifications
Roller Shade Driver E1
Color: White
Product Model: RSD-M01
(R-Roller, S-Shade, D-Driver, M-Motor, 01-The First Generation)
Wireless Protocol: Zigbee 3.0 IEEE 802.15.4
Dimensions: 43×38.5×175 mm (1.69×1.52×6.89 in.)
Operating Temperature: -10°C ~ 55°C (14°F ~ 131°F)
Operating humidity: 0-95% RH, no condensation
What is in the box: Roller Shade Driver E1 × 1, Screw × 2,
Expansion Tube × 2, Double-Faced Adhesive Tape × 1, Spare
Rotating Plate × 3, USB-C to USB-A Cable × 1
Battery Type: Lithium battery (not replaceable)
Restore the
device to factory
settings & enter
network
configuration
status
Long press RESET button for 5 seconds, till
the indicator turns to blue and flashes
continuously:
At the moment, the device is restored to
factory settings and enters network
configuration status.
Network configuration status can last for 30
seconds, and in this period:
a.If the device is connected to the network
successfully, the indicator will stop
flashing.
b.If something goes wrong and the device
failed to connect to the network, the red
indicator will be on shortly and then o.
c. If there is no operation, the indicator will
be o aer 30 seconds and the network
connection will end.
7

Zigbee Warnings
Zigbee Operation Frequency: 2405-2480 MHz
Zigbee Maximum Output Power ≤ 13 dBm
Under normal use of condition, this equipment should be kept a
separation distance of at least 20cm between the antenna and
the body of the user.
Rated Input: 5V 1A
Total Power Consumption: 5W
Standby Time: Two months (supposed to control a roller shade
of 1.8m*1.8m up and down once a day)
EU Declaration of Conformity
Hereby, Lumi United Technology Co., Ltd. declares that the radio
equipment type Roller Shade Driver E1, RSD-M01 is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: https://www.aqara.com/DoC/
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and
electronic equipment (WEEE as in directive 2012/19/EU) which
should not be mixed with unsorted household waste. Instead, you should
protect human health and the environment by handing over your waste
equipment to a designated collection point for the recycling of waste
electrical and electronic equipment, appointed by the government or local
authorities. Correct disposal and recycling will help prevent potential
negative consequences to the environment and human health. Please
contact the installer or local authorities for more information about the
location as well as terms and conditions of such collection points.
UK Declaration of Conformity
Hereby,Lumi United Technology Co., Ltd. declares that the
radio equipment type Roller Shade Driver E1, RSD-M01, is in compliance
with Directive 2017 (SI 2017 No. 1206, as amended by SI 2019 No. 696).
The full text of the UK declaration of conformity is available at the
following internet address: http://www.aqara.com/DoC/.
Online Customer Service: www.aqara.com/support
Customer Support Email: [e-mail]
Website: www.aqara.com
Manufacturer: Lumi United Technology Co., Ltd.
Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave,
Taoyuan Residential District, Nanshan District, Shenzhen, China.
Made in China
8