Nakanishi EM-3030T User manual

OPERATION MANUAL
Brushless Motor
Thank you for purchasing the Brushless Motor " EM-3030T ". The E3000 CONTROLLER, Spindle, Motor Cord
and Air Line Kit are required to drive this Brushless Motor. Read this and all the associated component Operation
Manuals carefully before use.
Always keep this Operation Manual in a place where a user can referred to for reference at any time.
■Read these warnings and cautions carefully and only use in the manner intended.
■These warnings and cautions are intended to avoid potential hazards that could result in personal injury to the
operator or damage to the device. These are classified as follows in accordance with the seriousness of the risk.
Class Degree of Risk
WARNING A safety hazard could result in bodily injury or damage to the
device if the safety instructions are not properly followed.
CAUTION A hazard that could result in light or moderate bodily injury or
damage to the device if the safety instructions are not followed.
CAUTIONS FOR HANDLING AND OPERATION
1.
①This Brushless Motor is not a hand tool. It is designed to be used on CNC machines or special
purpose machines.
②Do not touch the cutting tool while it is running. It is very dangerous.
③Wear safety glasses, dust mask, and use a protective cover around the Brushless Motor whenever
the Brushless Motor is rotating.
④Never connect, disconnect or touch the Power Cord Plug or Motor Cord Plug with wet hands. This
may cause an electric shock.
⑤Never operate or handle the Brushless Motor and spindle until you have thoroughly read the
Operation Manuals and safe operation has been confirmed.
1) To prevent injuries / damages, check the Brushless Motor, spindle and cutting tool for proper
installation, before operating the Brushless Motor and spindle.
2) Before disconnecting the Brushless Motor and spindle, always turn the control power off
and turn the compressed air supply to the CONTROLLER off. Then it is safe to remove the
Brushless Motor and spindle.
⑥When installing a Brushless Motor to a fixed base, make sure the fixed base is grounded in order
to avoid the risk of an electric shock.
WARNING
①Do not drop or hit this Brushless Motor, as shock can damage to the internal components.
②When cleaning a Brushless Motor, stop the Brushless Motor and remove debris with a soft brush
or a cloth. Do not blow air into the Brushless Motor with compressed air as foreign particles or
cutting debris may get into the ball bearing.
③Select suitable products or tools for all applications. Do not exceed the capabilities of the
Brushless Motor or tools.
④Do not stop the supplied cooling air to the Brushless Motor during operation of the machine.
Removing the air pressure from the Brushless Motor causes a loss of purging, allowing the
Brushless Motor to ingest coolant and debris. This will cause damage to the Brushless Motor.
⑤Stop working immediately when abnormal rotation or unusual vibration are observed. Immediately,
please check the content of section " 9. TROUBLESHOOTING ".
⑥Always check if the connection hose and supply air hose for damaged before and after operating.
⑦After installation, repair, initial operation, or long periods of non operation, please carry out break
-in as follow. Start rotating slowly and over a short period of 15 - 20minutes, increase speed
gradually until Maximum Allowable Motor Rotation Speed.
⑧Do not disassemble, modify or attempt to repair this Brushless Motor. Additional damage will
occur to the internal components. Service must be performed by NSK NAKANISHI or an authorized
service center.
⑨When using this Brushless Motor for mass production, please consider the purchase of an
additional Brushless Motor to be used as a back-up in case of emergency.
⑩Securely connect the compressor supply connection hose to the Air Line Kit, and connect
the air hose to the Air Line Kit, the CONTROLLER and the Brushless Moor to avoid accidental
disconnection during use.
CAUTION
BASIC PACKAGE
2.
When opening the package, check if it includes all items listed in " Table. 1 Packing List Contents ". In the event of
any shortage, please contact either NAKANISHI (see the " 4. CONTACT US " section) or your local dealer.
Table. 1 Packing List Contents
Brushless Motor・・1pc. Wrench (22 x 27) ・・1pc. Operation Manual・・1set
27
22
○○○○○○○○○○○
○○○○○○○○○
□□ ○○○○
□□.
□□□□
□ □
□□□□□□□
□□□□□□
□□□□□□□
□□□□□□
□□□□□□□
□□□□
□□□□□□□
□□□□
□□□□□□
□ □ □
□□□
□□□
□□□□□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□□□□□
□□□□□
□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□
□□□□□□□□□□
取扱説明書
OPERATION MANUAL
WARRANTY3.
We provide a limited warranty for our products. We will repair or replace the products if the cause of failure is due to
the following manufactures defects. Please contact us or your local distributor for details.
①Defect in manufacturing.
②Any shortage of components in the package.
③Where damaged components are found when initially opening the package.
(This shall not apply if the damage was caused by the negligence of a customer.)
CONTACT US4.
For your safety and convenience when purchasing our products, we welcome your questions.
If you have any questions about operation, maintenance and repair of the product, please contact us.
Company Name
Business Hours
U.S. Toll Free No.
Telephone No.
Fax No.
Web Address
:
Industrial Div.
: 8:30am to 17:00pm (CST)
(closed Saturday, Sunday and Public Holidays)
: 800-585-4675
: 847-843-7664
: 847-843-7622
: www.nskamericacorp.com
Contact UsContact Us
For U.S. Market
Company Name
Business Hours
Telephone No.
e-mail Address
:
: 8:00am to 17:00pm
(closed Saturday, Sunday and Public Holidays)
: [phone]
: [email protected]
For Other Markets
FEATURES5.
①The Brushless Motor housing is made from precision ground, hardened, stainless steel (SUS) with an outside
diameter of φ30mm.
②Excellent durability and high reliability are obtained by using a high-speed brushless motor, which eliminates
the need for brush replacement and frequent maintenance.
③The maximum output is 350W.
④Air-cooling system with a small volume of air (30ℓ/ min) is used to prevent heat buildup and allows long
continuous operation.
SPECIFICATIONS AND DIMENSIONS6.
6 - 1 Specifications
Model EM-3030T
Maximum Motor Rotation Speed 30,000min-1 (rpm)
Max. Output 350W
Weight 350g
Noise Level at 1m distance Less than 70dB (A)
Temperature Humidity Atmospheric Pressure
Operation Environment 0 - 40°CMAX.75%
(No condensation) 800 - 1,060hPa
Transportation and Storage
Environment -10 - 50°C 10 - 85% 500 - 1,060hPa
<Option>
*Note : Motor Cord is sold separately.
Please select the suitable motor cord length for your application.
・Do not exceed the Maximum Motor Rotation Speed (Refer to " 6 - 1 Specifications " ).
・This Brushless Motor should be connected to the Applicable CONTROLLER (Refer to " Table. 2
Identifying the Applicable CONTROLLER ").
If this Brushless Motor is connected to non applicable CONTROLLER, the Brushless Motor will
not rotate and Error " EL " (Incompatible Motor) will be displayed on the Digital Speed Indicator,
indicating a " Detection of unsafe operating conditions " of the CONTROLLER.
CAUTION
Table. 2 Identifying the Applicable CONTROLLER
Identifying Point Applicable CONTROLLER Non applicable CONTROLLER
Color of Air Output Joint
First letter of the Serial
No. on the Rating Plate or
Blue White
First letter : Other than " D "
XXXXXXX
DXXXXXXX
First letter : " D "
EM - 3030T
OM-K0693E
First letter : " D "
DXXXXXXX
Motor Cord
*Note
<S Type> Straight EMCD-3000-4M (4m) / 6M (6m) / 8M (8m)
(The Air Hose of the same length is attached.)
<A Type> Angle EMCD - 3000A - 4M (4m) / 6M (6m) / 8M (8m)
(The Air Hose of the same length is attached.)
OM-K0693E_EM-3030T_(629-3_5段)_EN_下版_171115.indd 1 2017/11/15 18:10:34

6 - 2 Outside View
-
0.02
-
0.03
φ30
（8.3） 89.3
(11)
34.5
φ29.9
Fig. 1
6 - 2 Outside View
6 - 3 Torque Characteristics
14
16
18
20
12
10
8
6
4
22
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
Torque (cN •m)
Output (W)
Rotation Speed (x103min-1(rpm))
350
400
450
500
300
250
200
150
100
50
0
Torque
Output
Continuous Duty Area
Fig. 2
CONNECTION OF MOTOR CORD7.
・Before connecting to the Motor Cord to the Brushless Motor and CONTROLLER, verify the Main
Power Switch on the CONTROLLER is turned OFF. If the Main Power Switch on the CONTROLLER
is ON while connecting the Motor Cord, damage to the CONTROLLER is possible.
・Install the Protective Cover (Protective Cover etc.) to prevent damage or contamination to the
Motor Cord Connector when not in use.
CAUTION
①Remove the Protective Cap of the Motor Cord Connector.
Fig. 3
②Carefully insert the Alignment Pin into the Alignment Hole and push straight into the Connector of the Motor
Cord.
Fig. 4
③Tighten the Connector Nut of the Motor Cord in a clockwise direction.
CONNECTION OF THE MOTOR TO THE SPINDLE8.
Make sure your hands and all interlocking parts of the spindle and Brushless Motor are clean before
connecting the Brushless Motor to the spindle. This is critical in preventing contaminants from
entering the Brushless Motor or spindle.
CAUTION
Align the thread on the front end of the Brushless Motor and the rear of the spindle, and turn the spindle clockwise.
If the drive shaft of the Brushless Motor does not engage properly to the drive dog on the spindle, it may only
turn approximately two threads before stopping. DO NOT FORCE THEM TOGETHER. Loosen the spindle from
the Brushless Motor, rotate the spindle shaft by hand then re-try. The drive shaft and the drive dog must be fully
engaged. When fully engaged, secure the Brushless Motor and spindle using the provided 27mm wrench (Fig. 5).
27
Transmission Clutch
Tighten
Turn
27
Fig. 5
TROUBLESHOOTING9.
If a problem or concern occur, please check the following items prior to consulting your dealer.
Trouble Cause Inspection / Corrective Action
Brushless Motor does
not run.
Power is not supplied. ・Make sure to turn ON the Main Power Switch
on the front of the CONTROLLER.
・Insert the power cord plug correctly into the
Main Power Inlet with Power Supply Fuses of
the CONTROLLER.
・Check if a fuse is blown.
Motor Cord Plug is not connected to
the Brushless Motor, CONTROLLER.
Connect the Motor Cord plug correctly
to the Brushless Motor and CONTROLLER.
The Brushless Motor is not connected
to an Applicable CONTROLLER (The
Error Code " EL " is displayed on the
Digital Speed Indicator on the E3000
CONTROLLER).
Connect the Brushless Motor to an Applicable
CONTROLLER after resetting the Error Code
" EL " (Refer to " 17 - 3 Resetting System
after Error Codes <Table 8> " of the E3000
CONTROLLER Operation Manual).
Control Button (CTRL) is set to
Manual mode but trying to start
with an External Command Signal
through Input / Output Connector A.
Start with the START / STOP Button (START /
STOP) or set the Control Button (CTLR) on the
Control Panel to Auto mode.
Control Button (CTRL) is set to
Auto mode but trying to manually
start with the START / STOP Button
(START / STOP) on the Control
Panel.
Start with an External Command Signal
or set the Control Button (CTRL) on the
Control Panel to Manual mode.
Emergency Stop Signal on External
Input / Output Connector B is ' OFF
(Open) ' (Only when the parameter
is set to on).
Set Emergency Stop Signal to be ' ON (Closed) '.
An Error has occurred (Error LED
(ERROR) of the E3000
CONTROLLER is lit).
Refer to " 17 - 3 Resetting System after Error
Codes <Table 8> " of the E3000 CONTROLLER
Operation Manual.
Error will not be released until cause of the
error has been removed.
Low air pressure (The Error Code
" E7 " is displayed on the Digital
Speed Indicator on the E3000
CONTROLLER).
Adjust to the air pressure 0.25 - 0.3MPa (36.3 -
43.5psi).
Can not set the increase
or decrease of the Motor
Rotation Speed.
Motor Fixed Speed is set in
Parameter.
Release Parameter .
Can not set the motor
speed to its maximum
allowable speed.
Either the required speed value is
higher than the maximum rotation
speed of the motor, or the upper
limit of the rotational speed has
been set in Parameter .
Set the Maximum Rotation Speed to a value
less than the Motor Rotation Speed set in
Parameter .
A blinking dot appears on
Digital Speed Indicator
of the CONTROLLER.
Cannot set the desired
rotation speed.
Gear Ratio is set to a value other
than " 1.0 ".
Check the setting of Gear Ratio.
When disposal of a Brushless Motor is necessary, follow the instructions from your local government agency for
proper disposal of industrial components.
Refer to the spindle and the E3000 CONTROLLER Operation Manuals.
DISPOSAL OF THE BRUSHLESS MOTOR10.
Contents are subject to change without notice.
Motor
Tighten
Connector Nut
Brushless Motor Side Motor Cord Side
Connector
Connector
Alignment Pin Alignment Hole
Blushless Motor Side Motor Cord Side
2017.11.15 002
OM-K0693E_EM-3030T_(629-3_5段)_EN_下版_171115.indd 2 2017/11/15 18:10:36