Aqua Essentials Borg & Overström B4 User manual

Borg & OverströmGB04
Dispense Options
Contents
Component/Feature Overview
Operation
Functions & Controls
General Safety
CO2 Bottle Installation
GB
B4
Chilled
Ambient
NOTE: This booklet to be left with
appliance following installation.
User Guide

Carbonation Switch
On/Off Switch
IEC Power Socket
CO2 Connector (1/4”)
Inlet Water (1/4”)
Drain Port
Control Panel
Drip Tray
Component/
Feature Overview
B4 -
Major Components

Control Panel
Drip Tray
Cup Dispenser
Level
Sensor
Alarm
Waste Tank

The relevant indicator lights
will be lit.
COLD
6
Connect and turn on the water
supply. Then connect the
power supply.
COLD
On sparkling models turn on
the carbonation switch on the
back of the unit.
3
Flush through 10 litres of water
before use.
2
borg&overström
45
10 L
borg&overström
8
COLD
1
7
All hot & non sparkling cold
tanks must be purged of air
by holding the corresponding
button.
Press and hold the cold water
button until water comes out.
To avoid damage do not turn
on the cold power switch
until water ows out of the
machine. (If applicable)
When the cold water switch
is turned on, the cold water
indicator will be lit.
Level
Sensor
Alarm
Waste Tank
Operation

Chilled Water
Button
Hot Water
Button
Ambient Water Button
(selected models)
Sparkling Water
Button
Sparkling/Hot LED
Hot/Chilled
LED
Chilled LED
borg&overström
Factory set to:
Cold Thermostat
NB: Turn clockwise to decrease water temperature
The temperature of cold water can be set from 39˚F to 52˚F.
-˚F
+˚F
Basic Settings
39˚F
52˚F
Functions & Controls
Controls

Basic Troubleshooting
Problem/Report Possible Cause Suggested Action
No Water Dispensing Water supply turned o.Check that power supply, and all taps/valves/
and are turned on.
Disconnectthe power and water supply, check
for leaks. To reset the machine contact your
distributor.
Faulty water pressure regulator, or other
failure.
Contactyourdistributor.
No/Low Sparkling Water No/incorrect CO2 pressure Check CO2 bottle, regulator and non-return
valve. Replace as necessary.
Contactyourdistributor.
Warm Drinks
fridge.
Contactyourdistributor.
Faulty compressor, or other failure.
Water lying on top edge of low -
er door panel and/or bottom
of cabinet.
Empty waste container and check drainpipe is
not blocked.
Water lying in bottom of
machine.
Contactyourdistributor.
Bleeping NoiseEmpty level sensor tank.
General Safety
•Leave a space noless than 6 inches
between the wall and dispenser.
•Keepthe machine away from
sunlight, heat andmoisture.
6 Inches

We recommend between
3.5 - 5 bar. Do not exceed 5
bar pressure.
5 Max bar
Flush through approximately
10 litres of water. Check
and adjust the CO2 pressure
accordingly.
It will be necessary to leave
the machine for up to 1 hour
for sparkling water to develop,
by absorbing the CO2.
6
1
hour
CO2 Bottle Installation - Sparkling Versions Only
OFF
Attach the regulator to the
disposable CO2 bottle,
ensuring the regulator is
closed.
1
Connect the assembled CO2
bottle and regulator to the
machine using 1/4 inch pipe.
COLD
After completing the water
installation, turn on the
sparkling power switch and
the pump will run. Do not
open the regulator valve until
the carbonated switch has
been turned on.
2 3
4510 L

For full distributor
service manual visit:
www.youraquaessentials.com
Customer services:
Email: [email protected]
Call: 1 [phone]
Fax: [phone]
Telephone
[phone]
Email
[email protected]
www.youraquaessentials.com
Aqua Essentials
1416 Antioch Pike, Suite 103
Nashville, TN 37013
Verson: 121718 - 01