AQUA FORTE PRIME VARIO 10000 User manual

1
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIOWIFI PUMP
AQUAFORTE PRIME VARIO
WIFI PUMP

2AQUAFORTE PRIMEVARIOWIFI PUMP VERSION 1.05 07/2022
• Please use the adapter and related accessories included.
• Do not put the pump in the flammable, explosive and corrosive liquid.
• Do not use the pump in the water temperature above 35°C.
• Maximum water depth 2M.
• Please refer to the reference table to use this product.
• Do not immerse the plug into water or other liquids.
• Do not allow children or the inexperienced to operate or play with the product alone without safety guarantee.
Prime Vario WiFi Pumps are inspected and tested to ensure the safety and operating performance of the product. Please read
this manual carefully before use to avoid any damage to the product due to improper operation, or maintenance to cause the
pump damage.
Pump Features
1. Smart Wi-Fi control function.
2. Smart AP mode control function(no router system need).
3. Dry and under water use.
4. With ceramic shaft and high quality SIC ceramic bearing, anti-corrosion.
5. Manual and smart adjustment of flow selection.
6. Permanent magnet brush-less motor, energy-saving 40%.
7. Suitable for indoor and outdoor use.
8. Wi-Fi Operating Frequency 2412 - 2472 MHZ.
9. Max. E.I.R.P power 18.96dBm.
1. Used as submersible pump: the water level should exceed the inlet of the pump to avoid pumping the air. It’s ok to add
the filter sponge in the mesh/front cover to avoid the suction of sundries and affect the pump performance. The pump
conjunction connector is designed with standard size thread, which can be connected to the common fountain heads and
water pipes.
2. Used as dry-use pump: the pump should be placed lower than the horizontal level to ensure water flowing into the water
pump. Meanwhile, remove the front filter cover to connect the water pipe in inlet and outlet to ensure water in the pump
and pipe before plug on.
WARNING:
1. INTRODUCTION:
2. USAGE:
AquaForte is a trademark of Sibo Fluidra Netherlands BV, Doornhoek 3950, 5465TC,Veghel
Email: [email protected] Website: www.aqua-forte.nl/en

3
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP
• Adjustable flow rate and head max.
• “Feed”mode, Pause,Timing, delay,Wi-Fi, Restart function.
• Memory function, ensuring that the pump rework while keeping the same parameter.
OPERATING INSTRUCTIONS:
When use the pump, please pay attention to the position of the pump. Please connect the pump supply after finishing the
installation. If the pump can’t pump the water out for the first time which may be caused by the air in the pump body. Please try
to plug off and re-plug on to vent the air.To ensure safety, please install a leakage switch with leakage current less than 30mA
when using outdoor (the leakage switch shall be installed by the user self).
CAUTION:
• Always disconnect the pump from the power supply before cleaning, maintenance and handling.
• Try to avoid the pump dry working.
• Do not lift the pump by holding the power cord only. In case of the cable connection off inside of the pump
• Do not use the pump in the heating liquid.
• The pump can’t be used in the swimming pool.
• This product has multiple protection functions. When it enters the protection state, please plug off and plug on to recover
the pump normal work.
3. CONTROLLER FEATURES:
3.1 Manual control
After connecting with pump, the control is set per last operation, LED display shows normal locking panel.“P XXw”is shown in
LED, P is short for power, and XXw stands for power consumption in watts (44 watt in the example).“30”stands for flow rate in
%, which can be set from 30 to 100%.When touch“ / ”button, LED will show the instant working condition, you can set
different power per your needed. When touch“II”(pause) button, LED screen shows“STOP”, the pump stop working on“Pause”
mode, press the“II ” button again to stop“Pause”mode. Adjust the pause time using the APP. When touch“ ”button, LED
display shows“OFF”, touch“ ”again to have the pump start running again.
Remarks:When the pump enters to the timer mode set by APP, the LED will display as P.XXX, then keep pressing“ ”to exit
the time.
Operation Function:
Controller panel
LED display screen
Flow / Function DOWN
Flow / Function UPWi-Fi / ON/OFF button
Pause button

4AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
3.2 Description and use of Wi-Fi buttons and displays
Wi-Fi Indication Light and Wi-Fi Button Instruction
A. PressWi-Fi button for about 5 seconds, theWi-Fi indication icon flashing.The Pump is into smart configuration mode.
B. Press Wi-Fi button for about 10 seconds, the Wi-Fi icon flashing, "AP" appears in the lower right corner. The Pump is into AP
configuration mode and AP direct connection mode.
Note: After connecting, theWi-Fi icon is always on and no longer flashing.
Wi-Fi Indication Light and Wi-Fi Button Instruction
A. PressWi-Fi button for about 5 seconds, theWi-Fi indication icon flashing.The Pump is into smart configuration mode.
B. Press Wi-Fi button for about 10 seconds, the Wi-Fi icon flashing, "AP" appears in the lower right corner. The Pump is into AP
configuration mode and AP direct connection mode.
Note: After connecting, theWi-Fi icon is always on and no longer flashing.
1. WIFI display position
2. P 44W: P represents power, 44W represents real-time
operating power
3. Indicates that the keys are locked
4. Flow value
5. Pump is in timing mode
6. Display normal screen brightness
7. Brightness of the screen saver mode
“Smart configuration mode” “AP configuration mode”
Power OFF Warning notice Feeding mode (pause)
Display
1
2
3
4
5
6
7

5
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP
4.1 Download
The APP name“Aqua Forte”, is available to download in App Store for Apple users, or Google Play for Android system users. The
User can search“Aqua Forte”in either App Store or Google Play to download the application. Alternative, the user may scan the
QR code on the package or user manual to download the application. (Note: Scan function in certain countries or areas may be
unavailable to read the QR code properly.)
4.2 User registration, login and password reset
1. Account registration
A. Open Aqua Forte App and tap Create new account.
B. Choose email way to register, fill the information as required and tap Create account;
C. After registration, return back to the login page. Enter the account and password to log in.
Note: Phone number registration is valid for mainland China only.
3.3 The Button Lock Function
In the running state of the pump, hold the“II”button for 3 seconds, and the lock pattern will be displayed on the display screen,
and all the button will be locked. Hold the“II”button again for 3 seconds, and the lock pattern in the display screen will disap-
pear and the button will be unlocked.
3.4 The Display Screen protection mode
In the power-on state of the controller, when the control key is not touched for more than 17 seconds, the display screen is dis-
played in a slightly bright state and enters the screen saver mode.When any key is pressed, the display screen returns to normal
brightness. At the same time, press and hold the“ ”button to enter the screen brightness level mode, and use the“ ”
button to adjust the normal brightness and the“ ”button adjusts the brightness of the screen saver mode.
3.5 Data memory function
When power off then power, the controller keeping the same default parameter to rework.
4. APP DOWNLOAD AND INSTRUCTION:

6AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
2. Reset Password
Tap Forget Password on the log-in page. Enter your
email address and tap Send link. Check your email and
follow the instructions to reset your password. Then
back to the log in page to input your account and new
password to log in.
Tap“Add Now”or tap the top right“ +”icon to add your device, tap the“Water Pump”Icon.
5.1 Main page
5.2 Add new pump
5. APP APPLICATION
Add new devices
Add new devices
Go to Setting
Go to My Group
Tap My Devices

7
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP
Press theWi-Fi button touch“ ”button for 5 seconds until theWi-Fi symbol starts blinking. The Device is in smart
configuration mode.
Choose the confirmation“Device is in smart configuration
mode”then tap“Next”, start to smart configuration.
Follow the instructions. EnterWi-Fi password and tap
Next.
Tap“Start”to start using your device.
Make sure your device, phone, and router are as close as possible during the configuration progress.The page will display all
the devices. Choose the request add device, tap on the device name, then tap ”Confirm to add”
5.3 Configuration mode:
Make sure your phone is connected to 2.4G bandWi-Fi before configuration.There are two configuration modes, Smart
configuration and AP configuration modes. Choose one mode to link your device.
1. Smart Configuration mode:

8AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
2. AP Configuration:
Press theWi-Fi button for about 10 seconds“AP”symbol
starts blinking next to theWIFI symbol. The Device
enters the AP configuration mode.
Tap“AP Network“ in the upper right corner on Add device
page to enter into AP configuration.
Choose the confirmation “Device is in AP configuration
mode”and tap“Next”
Enter the correct Wi-Fi password and tap“Next”
3. PS: Due to different operating system, IOS and Android will operate differently in the following details.
IOS System:
After entering the Wi-Fi password, you need to switch manually theWi-Fi of the phone to“Aqua_Forte_WiFi-xxxx”, the specific
operation as below:
Tap Go to settings (image 1). Tap“Settings”in the upper left corner to enter the
mobile phone settings page (image 2), then enter theWIFI setting page (image 3).
Go to Settings >Wi-Fi and choose the Aqua_Forte_WiFi-xxxx”with password
123456789. Connecting the Aqua Forte-WiFi (image 4).
1

9
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP
After connection successfully, tap“Aqua Forte“ to return back to the APP.
The configuration starts automatically.Tap“Start”(image 5) to control the device after the device has been added successfully.
Android:
After input theWi-Fi password, need to manually switch the Wi-Fi connection "Aqua_Forte_WiFi_xxxx".The specific operation
is as follows.
Click ”Confirm”, Enter the mobile phone
Wi-Fi setting page.
On theWi-Fi Settings screen (image 2),
switch theWi-Fi of the mobile phone to
“Aqua_Forte_WiFi-xxxx”with the password 123456789 (image 3). After successful connection, Return to APP and wait.
345

1. In the APP login interface, tap the
Access Point (direct) connection at the
bottom right or tap the login to enter
themaininterface and select the Access
Point (direct) connection in Settings.
2. Select the device type, check the confirmed device to enter AP hotspot mode and tap Next.
3.Tap Confirm. Jump to the phoneWIFI setting interface.
4. Select the hotspot "Aqua_Forte_Wi-Fi-xxxx" issued by the device (the name is the same as the device name), enter the
password 123456789 and tap Connection. Manually return to APP after successful connection.
or
Settings
10 AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
4. Hotspot (AP direct connection)
Press theWIFI button of the device for 10 seconds until the“AP”symbol appears flashing next to theWiFi symbol and let go.

VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP 11
5.Wait for the device to connect, and tap the device to enter the control interface
5.4 Pump control
After adding the pump device successfully, long press the pump icon for 2 seconds to enter the pump control page.
1. Manual mode:
Drag the arc progress bar to change the flow value of the pump.The minimum flow is 30% and the maximum is 100%.
Notice:
1. You may be asked to restart configuration process all over again if theWi-Fi pass-
word input is incorrect.
2. Make sure the device, mobile phone and router are placed as close as possible.
3. AP direct connection is only suitable for temporary control of the device in a non-
WiFi environment. (Manual calibration time is required when the equipment is
directly connected to AP after delivery. SeeV.4 Pump Management for detail.)
Hold the icon for 2 seconds Manual control bar
ON/OFF
Current flow value
Pause icon
Program icon

12 AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
Manual pause mode:
The pump will stop working immediately according to the setting pause time.
Hold the "Pause" icon 2 seconds to enter the pause settings.
Set the pause time, turn on the switch,
then tap save and return.

13
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP
2. Program mode:
Hold the "Program" icon 2 seconds to enter the setting page and set the working mode of the pump at various times every day,
including the pump stop, automatic and feeding.
Tap the "Stop, Auto, Feed" icon or, tap the circle twice to edit each time period.
Tap the circle twice
Choose mode
Time switch button
Gears setting (flow in %)
Adjust the time
Start time setting
Mode selection
End time setting

14 AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
1
2
3
4
5
1. Double-click the blank circle area to add the program
time period or use the time switch button to switch
to the blank circle area to automatically add the
program time period.
2. Choose the work mode of the program time period
3. Drag the slider to adjust the start and end time or to
modify start and end time directly.
4. Tap“Done”to save the plan setting.
5. If you want to delete the current setting period, then
tap delete.
After the setup is completed, return back to the main page and tap the“Program”icon to run the program mode.
PS:The program mode will be closed if you manual set the flow stage (Program mode effect after ending the manual mode).
5.5 Pump management
On the device’s main page, tap on upper right-hand side to device management page. User can calibration time, rename, delete
device.To add back the device, you need to start configuration again.

15
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP
5.6 Failure indication
1. The factory time of the equipment may not be accurate, so the first time to use the AP direct connection mode of the mobile
phone needs to set the calibration time (tap the set time).
2. Users can also change the name of the pump to facilitate management.
3. You can also delete the current pump, but when you want to add another pump, you should reconfigure the network to add
the pump. Reset theWi-Fi module if necessary.

16 AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
6. MAINTENANCE
7. DISPOSAL
LED Error code and APP Error description:
When the controller work abnormal, the controller will show the Error code and warning flashing, when enter the APP will pop-
up the mention box. the code explanation as below.
APP mention and error code:
If the pump is not working, check as following:
• Connect with another power outlet to check if the circuit is connected, disconnect the power before operation;
• Check the pump inlet and outlet, check the connecting pipe for any dirt blockage;
• Remove the pump inlet to access the impeller. Turn around the rotor to check if broken or jammed.
• Monthly maintenance will prolong your pump life. Clean the rotor, remove the dirt etc.
• The power cord of the pump must be under the power socket to form a drip ring to prevent water into the power socket
along the power cord
Please don’t dispose this product as unsorted municipal waste. Collection of such waste separately for special
treatment is necessary. Not put it together with the domestic waste which should be solved as an authorized
place for recycling of electrical and electronic appliances for collecting and recycling waste. Please consult
with your local seller, to make sure the product is disposed in an environmental and healthy way.
APP prompt LED panel Exception to rule out
Controller over current Er01
Abnormality Working current; Check
if the pump is short of voltage or the
controller is broken.
Controller over temperature Er02
Check whether the controller is
exposed to sunshine or in high
temperature environment.
Pump idiling Er03
The pump is idiling. Check whether
the pump works dry. The pump must
be filled with water before operation.
The pump was blocked Er04
The impeller stops running, clean
the pump and impeller to ensure the
impeller is clean and works.
Controller over voltage Er05 Check the input supplying voltage.
Controller under voltage
WiFi module and motherboard
communication failure Er06
Bad contact between motherboard
and module, communication part
damage

17
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP
• Gebruik de meegeleverde adapter en bijbehorende accessoires.
• Plaats de pomp niet in ontvlambare, explosieve en corrosieve vloeistoffen.
• Gebruik de pomp niet bij een watertemperatuur boven 35°C.
• Maximale waterdiepte 2M.
• Raadpleeg de referentietabel voor het gebruik van dit product.
• Dompel de stekker niet onder in water of andere vloeistoffen.
• Laat kinderen of onervaren personen het product niet alleen bedienen of ermee spelen zonder veiligheidsgarantie.
PrimeVarioWiFi-pompen zijn geïnspecteerd en getest om de veiligheid en de werking van het product te garanderen. Lees deze
handleiding zorgvuldig door voordat u het product gebruikt, om te voorkomen dat het product beschadigd raakt door onjuiste
bediening of onderhoud, waardoor de pomp beschadigd kan raken.
Pomp functies
1. SlimmeWi-Fi-besturingsfunctie.
2. Smart AP-modus controlefunctie (geen router systeem nodig).
3. Droog en onder water te gebruiken.
4. Met keramische as en hoge kwaliteit SIC keramische lager, anti-corrosie.
5. Handmatige en slimme aanpassing van flow selectie.
6. Borstelloze motor met permanente magneet, 40% energiebesparend.
7. Geschikt voor binnen- en buitengebruik.
8. Wi-FiWerkfrequentie 2412 - 2472 MHZ.
9. Max. E.I.R.P vermogen 18.96dBm.
1. Gebruik in het water: het waterniveau moet hoger zijn dan de inlaat van de pomp om het pompen van lucht te voorkomen.
Het gebruik van een filterspons in het voorfilter kan voorkomen dat er zand in de pomp wordt gezogen en de pompwerking
wordt beïnvloed. De aansluiting van de pomp is ontworpen met standaard schroefdraad, die kan worden aangesloten op de
gebruikelijke fonteinkoppen en waterleidingen.
2. In droge opstelling: de pomp moet lager dan het waterniveau worden geplaatst om ervoor te zorgen dat er water in de
pomp stroomt. De filterkorf kan niet worden gebruikt, de pomp moet rechtstreeks op de inlaat/uitlaat worden aangesloten,
zodat er water in de pomp en de leiding komt voordat u de stekker in het stopcontact steekt.
WAARSCHUWING:
1. INTRODUCTIE:
2. GEBRUIK:
AquaForte is een handelsmerk van Sibo Fluidra Netherlands BV, Doornhoek 3950, 5465TC,Veghel
Email: [email protected] Website: www.aqua-forte.nl

18 AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
3.1 Handmatige bediening
Na het aansluiten op de pomp, wordt de regeling ingesteld volgens de laatste bediening, LED display toont normaal vergren-
delingspaneel. "P XXw" wordt weergegeven in display, P is een afkorting voor power, en XXw staat voor stroomverbruik in watt
(44 watt in het voorbeeld). "30" staat voor de flow in %, welke ingesteld kan worden van 30 tot 100%.Wanneer u de " / "
toets aanraakt, zal het display de actuele werkingsstatus tonen en kunt u het vermogen naar wens instellen.Wanneer u de knop
"II" (pauze) aanraakt, toont het display "STOP". De pomp stopt met werken in de "Pauze"-modus, druk nogmaals op de knop "II"
om de "Pauze"-modus te stoppen. Pas de pauzetijd aan met behulp van de APP.Wanneer u de“ ”-toets aanraakt, geeft het
display "OFF" (UIT) weer, druk opnieuw op " "om de pomp weer te laten werken.
Opmerking:Wanneer de pomp in de door de APP ingestelde timermodus komt, zal het display P.XXX weergeven, houdt de
" " knoppen gelijktijdig ingedrukt om de tijd modus te verlaten.
• Instelbare flow en opvoerhoogte.
• "Feed" mode, Pauze,Timing,Vertraging,Wi-Fi, Herstart functie.
• Geheugenfunctie, zorgt ervoor dat de pomp opnieuw werkt met behoud van dezelfde parameter.
BEDIENINGSINSTRUCTIES:
Wanneer u de pomp gebruikt, let dan op de positie van de pomp. Sluit de pomp aan nadat de installatie is voltooid. Als de pomp
het water de eerste keer niet kan wegpompen, kan dit worden veroorzaakt door lucht in het pomphuis. Probeer dan de stekker
uit het stopcontact te halen en weer aan te sluiten om de lucht te laten ontsnappen. De pomp moet voor de veiligheid op een
lekstroomschakelaar met een lekstroom van minder dan 30 mA worden aangesloten.
LET OP:
• Koppel de pomp altijd los van de stroomtoevoer voordat u hem reinigt, onderhoudt en behandelt.
• Probeer te voorkomen dat de pomp droog werkt.
• Til de pomp niet op door alleen het netsnoer vast te houden, dit kan de kabelverbinding binnenin de pomp beschadigen.
• Gebruik de pomp niet in warme vloeistof.
• De pomp kan niet worden gebruikt in zwembaden.
• Dit product heeft meerdere beveiligingsfuncties. Wanneer het in de beschermingsstatus komt, gelieve de stekker uit te
trekken en weer in te pluggen om de pomp weer normaal te laten werken.
3. CONTROLLER FUNCTIES:
Bedieningsfuncties:
Bedieningspaneel
LED display
Flow / Functie OMLAAG
Flow / Functie OMHOOGWi-Fi / ON/OFF knop
Pauze knop

19
VERSION 1.05 07/2022 AQUAFORTE PRIMEVARIO WIFI PUMP
3.2 Beschrijving en gebruik van Wi-Fi knoppen en displays
Wi-Fi symbool en Wi-Fi knop Instructie
A. Druk ongeveer 5 seconden op de Wi-Fi-knop, het Wi-Fi-indicatiesymbool knippert. De pomp is in de "smart" configuratie
modus.
B. Druk ongeveer 10 seconden op de Wi-Fi-knop, hetWi-Fi-pictogram knippert en "AP" (Access Point) verschijnt in de rechter-
benedenhoek. De pomp schakelt over naar de AP-configuratiemodus en AP directe verbinding-modus.
Opmerking: Na verbinding te hebben gemaakt, is hetWi-Fi-pictogram altijd aan en knippert het niet meer.
3.3 De display Lock Functie
Als de pomp in bedrijf is, houdt u de "II" (Pauze) knop 3 seconden ingedrukt; het slot symbool verschijnt in het display en alle
knoppen worden vergrendeld. Houd de "II" knop nogmaals 3 seconden ingedrukt waarna het vergrendel symbool zal
verdwijnen en de knoppen zullen worden ontgrendeld.
1. WIFI symbool
2. P 44W: P staat voor“power”, 44W is het huidige stroom
verbruik in wattage
3. Geeft aan dat de knoppen zijn vergrendeld
4. Flow waarde (in % van 30% tot 100%)
5. Pomp is in timing mode (via APP)
6. Helderheid van het display in normale mode
7. Helderheid van het display in screen saver mode (scherm
wordt na bepaalde tijd donkerder als het niet wordt gebruikt)
“Smart configuratie mode” “AP configuratie mode”
Pomp is uit Waarschuwingsmelding Pomp is gestopt (inTimer mode)
Display
1
2
3
4
5
6
7

20 AQUAFORTE PRIMEVARIO WIFI PUMP VERSION 1.05 07/2022
2. Wachtwoord resetten
4.1 Download
De APP met de naam "Aqua Forte" kan worden gedownload in de App Store voor Apple-gebruikers, of in Google Play voor
Android-systeemgebruikers. De gebruiker kan "Aqua Forte" zoeken in App Store of Google Play om de applicatie te download-
en. Als alternatief kan de gebruiker de QR-code op de verpakking of de gebruikershandleiding scannen om de toepassing te
downloaden. (Opmerking: In bepaalde landen of gebieden is het mogelijk dat de scanfunctie niet beschikbaar is om de QR-code
correct te lezen).
4.2 Gebruikersregistratie, aanmelding en wachtwoordreset
1. Account registratie
A. Open Aqua Forte App en tik op Nieuwe account aanmaken.
B. Kies voor e-mail om te registreren, vul de informatie in zoals vereist en tik op Account aanmaken;
C. Keer na de registratie terug naar de inlogpagina.Voer het account en wachtwoord in om in te loggen.
Opmerking:Telefoon nummer registratie is alleen geldig voor het vasteland van China.
3.4 Screen saver mode
Als in de ingeschakelde toestand van de controller de bedieningsknoppen gedurende meer dan 17 seconden niet worden
aangeraakt, wordt het displayscherm in een minder heldere toestand weergegeven en gaat dan over in de screensaver-modus.
Wanneer een willekeurige toets wordt ingedrukt, keert het displayscherm terug naar de normale helderheid. Houd gelijktijdig
de " " knoppen ingedrukt om naar de stand voor het helderheidsniveau van het scherm te gaan, en gebruik de " " knop
om de normale helderheid in te stellen en de " " knop om de helderheid van de screensaver in te stellen.
3.5. Data memory functie
Wanneer de stroomvoorziening wordt onderbroken en weer wordt hersteld zal de controller volgens de laatst gekozen instelling
gaan werken.
4. APP Downloaden en instructies
Tik op "Wachtwoord vergeten" op de inlogpagina. Voer uw e-mailadres in
en tik op "Verzend" link. Controleer uw e-mail en volg de instructies om uw
wachtwoord opnieuw in te stellen. Ga dan terug naar de inlogpagina om uw
account en nieuw wachtwoord in te voeren om in te loggen.