aquaBUBBLER AB12 User manual

45
6
Classic/Universal aquaBUBBLER
Determine Orientation
Identify Water & Drainage points
IMPORTANT >>>
Determine Plumbing Connection
3
SPORTS FIELD
Wall
WALKWAY
CORNER
1
Outdoor Indoor
2
Install onto :
Pre-installation
Below GroundAbove Ground
Keyhole
Locate Keyhole OUTSIDE
Black Zone for accessibility
Location:
1
Concrete
Pad
Ground
Work Timber Floor
Product Code: AB12/ABUA13/AB2UA14
WASTE
W A TER
WASTE
W A TER
Unit must be installed by a Certified Plumber - failure to do so will void all warranties.
7 8
Timber boxing foundation
Screws and washers
Bag of cement
Socket Extension Bar
10 mm threaded rod and nuts
Flexible head ratchet wrench
43 mm hole saw
15 mm hole saw
10 mm socket
1
1
22
3
3
44
5
5
66
7
7
88 9
9
Where installed in
frost-prone areas,
unit must be fitted
with an Anti-Freeze
Valve. Warranty will
otherwise be void
Is an Anti-Freeze
Valve Required?
Plumbing Tools Required
ATTENTION PLUMBER: See next page for INSTALLATION GUIDE
Decide Location of Inlet/Outlet
Do not place
Drain Outlet under
the Side Pod:
this will obstruct
wheelchair access
WALL
Front
Pod
Locate Drain Outlet and
Mains Water Inlet at
back of unit (out of
view), or at either side
if necessary
Maximum Water Pressure: 1600 kPa / Maximum Temperature: 65°C
Installation must be in accordance with AS/NZS 3500.1 and AS/NZS 3500.2
AU: 1300 213 7 74
NZ: 0800 213 774
www.aquabubbler.com

2
78
Attach Side Pod
Connect pipe to
tap fitting
Connect Black
Director from
Pod to the
Waste Pipe
Screw Side Pod
to body with a
5mm Allen Key
(not supplied)
Insert coach bolts
through square
holes (either side
of DB)
Secure bolts from
inside of unit
with washer and
lock nut
1
2
1
1
2
3
2
3
3
Mark measurements and
dimensions as indicated
by Schematic
1Consult
Schematic
DON’T FORGET:
Seal all plumbing
Apply sealant to
T-junction pipe ends
before insertion into
other pipes
Check for leaks
Run taps and adjust
any insecure
connections
Attach DB
aquabubbler.com.au/plumbing-
technical-information
ATTENTION PLUMBER: See previous page for PRE-INSTALLATION GUIDE
45
2Locate Internal Base Mounting Plates
water
mains
DON’T Install S-Trap
below the pod !!
Pod has its
own in-built
S-Trap
Install
Isolation Valve
(not supplied)
3
water
supply
Flush out
the lines
on mains line,
external to unit
(recommended)
SET UP FOR USE:
Run the tap
Adjust water pressure
Rotate keyhole with a
5mm screwdriver to
adjust water pressure
until the pod is full
Advise client to check
water pressure 48 hours
aer installation, as it may
require re-adjustment
Leave T15 Post Torx
Security Screwdriver
with client
Classic/Universal aquaBUBBLER
IMPORTANT >>>
Installation
Product Code: AB12/ABUA13/AB2UA14
Unit must be installed by a Certified Plumber - failure to do so will void all warranties.
Maximum Water Pressure: 1600 kPa / Maximum Temperature: 65°C
Installation must be in accordance with AS/NZS 3500.1 and AS/NZS 3500.2
AU: 1300 213 7 74
NZ: 0800 213 774
www.aquabubbler.com
*Indicates correct gauges for anchor
system types listed; choice of anchor
system is at installer's discretion
Place Base Mounting Plate (BMP) halves
in position on the installation surface.
Position the BMP so that the Front of the
unit will be in the middle of 2 holes.
Mark anchor points on the surface
through BMP holes and drill out.
Fit o either 12mm threaded rods
or 16mm dynabolts*
Remove PVC S-Trap inside to gain
access to the base of the unit.
Place unit over anchors, then place
BMP halves back inside unit over
anchors and secure in place.
Front of unit
BMP
before connecting to
unit in order to
eliminate particulate
matter (copper &
brass filings)
will end up here
(between two holes)
6a 6b
Universal
aquaBUBBLER
only
Units with
Dog Bowl (DB)
only