Oasis Osmosis Home User manual

Congratulations on your new Oasis Osmosis Home RO system purchase!
Let’s learn how to install it in just 30 minutes!

Required Tools:
Adjustable wrench
Screw driver
Utility knife
Variable speed drill
Drill bit
Flash light
Towel
2

Check the box to make sure you
have all the components:
System Housing x 1 set
Activated Carbon Block
Composite Filter x 1
RO Membrane Composite Filter x 1
RO faucet x 1
Feed Water Adapter x 1 set
Lock Clips x 6
Screws x 5
3
Power Cord x 1
White 3/8” PE tubing
White 2/8” PE tubing
Mount washer and nut x 2
Quick-connect fitting x 2
Tubing Holder clip x 1
Drain saddle - Part not included in the
package. It will be shipped separately.

4
Install the feed
water adapter
Step 1

5 Step 1
Shut o the water supply and
turn on the kitchen faucet to
release pressure.
Connect the feed water adapter
to the cold-water valve. (A)
Position the RO system housing
under the sink. (B)
A
B

6 Step 1
C
D
Before you cut each of the 2 tubes in
half, measure the distance needed
for the tubing length to reach the
osmosis system, faucet, and water
intake port and feed water adapter
to be sure that they can reach,
according to your home setup.
Cut the included 2 tubes in half (or
dierent length, based on your
measurement and setup).
Connect the 3/8” tubing between the
Water intake port and the feed water
adapter. (C)
Connect the other 3 tubings to the
ports on the RO system housing. (D)

7
Install the
RO Faucet
Step 2

8 Step 2
E
Using a stainless steel suitable drill bit,
drill a hole in the countertop large
enough to fit the two small piping on
the bottom of the faucet but small
enough to allow support of the faucet
base and ensuring it does not go
through the hole.
Insert RO faucet piping into the hole. (E)

F
G
Install the mounter washer and
screw the nut on to the threaded
tubing under the sink. (F)
Insert the quick-connect fittings in
the faucet stems. (G)
9 Step 2

H
I
Connect the tubing from the
Water outlet port to the
bigger quick-connect fitting
on the faucet stem. (H)
Connect the tubing from the
Pure water nozzle port to the
smaller quick-connect fitting
on the faucet stem. (I)
10 Step 2

11
Install the
Drain saddle
Step 3
Drain saddle will be shipped separately.

Drill a quarter inch hole on
the vertical drain pipe. (J)
Separate the front and back
plates of the drain saddle. (K)
12 Step 3
J
K

Take down the front plate
and insert the tubing. (L)
Attach the back plate to the
drain pipe. (M)
13 Step 3
L
M

Tighten the screws evenly. (N)
Connect the tubing from the
Waste water port to the
drain saddle. (O)
14 Step 3
N
O

15
Plug in
RO system
Step 4

P
Q
Insert the power cord in
power socket port (P) and in
the wall power socket. (Q)
16 Step 4

17
Insert filters
Step 5

Insert the filters, one at a time,
being sure to match the filters
to their correct filter holes.
Push them in and then twist
until you hear a clicking sound
to confirm it is in place. (R)
18 Step 5
R

19
Turn on the
RO System
Step 6

S
O
Turn on the cold-water valve
and feed water adapter.
Turn on the tap water faucet
and let it discharge for 10
minutes. (S)
Turn on the pure water faucet.
Press the power switch. (O)
The RO system will start to run
water and after an hour you’ll
have fresh, clean water.
20 Step 6