AQUAMOTION AMK-WB User manual

Instruction Sheet
Instructions for Setup of the AMK-WB
The transmitter and receiver are programmed as matched at the factory. No more
programming is required, Additional transmitters will require programming with the
receiver.
88C Jefferson Blvd, Warwick, RI 02888 ● 401-785-3000 ●Fax: [phone] ● [e-mail]
Effective: 9/5/14
Supersedes: New
IS-AM09-606
1. The transmitter and receiver must be within 100
feet of each other in an open area when using
or programming. They work best when avoiding
metal surfaces.
2. On the wireless transmitter (remote control),
remove the yellow plastic band on the back of
the battery cover. The lamp on the front (above
the pushbutton) should light Red. Then press
the pushbutton, and the lamp should flash red.
3. On the wireless receiver, plug the white antenna
into the side of the unit.
4. On the wireless receiver, plug the pump into the
AC plug on the unit.
5. Plug the power cord of the wireless receiver into
an AC outlet in the wall. The lamp on the
receiver will light red for a second.
6. It is now ready to use. When the transmitter is
not being used, it should be docked in the
holder.
7. To check this, press the pushbutton on the
wireless transmitter again to check that the
pump runs for 5 minutes. If it does not, then
follow the instructions for Programming of the
AMK-WB.
Instructions for Programming of the
AMK-WB
1. The transmitter and receiver must be within
100 feet of each other in an open area
when using or programming. They work
best when avoiding metal surfaces.
2. On the wireless transmitter (remote
control), remove the yellow plastic band on
the back of the battery cover. The lamp on
the front (above the pushbutton) should
light Red. Then press the pushbutton, and
the lamp should flash red.
3. On the wireless receiver, plug the white
antenna into the side of the unit.
4. On the wireless receiver, plug the pump
into the AC plug on the unit.
5. Plug the power cord of the wireless receiver
into an AC outlet in the wall. The lamp on
the receiver will light red for a second.
6. You must complete step 6 and 7 within 25
seconds or you will have to repeat them.
.On the wireless receiver, press the white
SET button for about 10 seconds until the
lamp is constantly red.
7. On the back of the wireless transmitter, use
a pen or nail to press the small red button.
This will make the lamp on the front to light
red for about 15 seconds. During this time,
press the pushbutton on the front. This
should turn off the red light on the wireless
receiver.
8. Unplug the wireless receiver. Then plug it
back into the wall AC outlet. The lamp will
light red for 1 second.
9. Please read the AMK-WB Time Window
explanation below to decide how long you
want your water to be hot before the next
step.
10. Press the pushbutton on the wireless
transmitter. This should turn on the pump.
If it does not, then go back to step 6.
11. For 5 to 10 minutes of hot water: on the
wireless receiver, press the white SET
button for about 6 seconds until the lamp
on the wireless receiver flashes twice in a

second (first it will flash once in a second,
but keep the SET button pressed down until
it flashes twice in a second). The pump
should run for 5 minutes then turn off.
For 15 to 20 minutes of hot water: on the
wireless receiver, press the white SET
button for about 13 seconds until the lamp
on the wireless receiver flashes three times
in a second (first it will flash once in a
second, but keep the SET button pressed
down until it flashes three times in a
second). The pump should run for 5 minutes
then turn off.
For 30 to 35 minutes of hot water: on the
wireless receiver, press the white SET
button for about 17 seconds until the lamp
on the wireless receiver flashes four times in
a second (first it will flash once in a second,
but keep the SET button pressed down until
it flashes four times in a second). The pump
should run for 5 minutes then turn off.
For 60 to 65 minutes of hot water: on the
wireless receiver, press the white SET
button for about 25 seconds until the lamp
on the wireless receiver flashes five times in
a second (first it will flash once in a second,
but keep the SET button pressed down until
it flashes five times in a second). The pump
should run for 5 minutes then turn off.
12. Unplug the pump from the wireless receiver
and plug in a lamp that is turned on. Press
the pushbutton on the wireless transmitter
again to check that the lamp is ON for the
time window that you decided then turns off.
If it runs for less or more than your time
window, then go back to step 8.
13. Remove the lamp from the wireless receiver
and plug in the pump.
The AMK-WB Time Window
Explanation:
1. The AMK-WB can be user programmed to
keep the water hot in a room for some
amount of time. This time interval can be
programmed to: 5 minutes, 15 minutes, 30
minutes or 60 minutes.
This is the time that the AMK-WB and Hot
pump will keep giving you hot water. All
units have been programmed for 30
minutes.
2. For example, say that you come into the
room and want to use hot water for 5
minutes (like for shaving) then not use hot
water for 15 minutes, then use hot water
again for a shower , then you would want to
program the AMK-WB for 30 minutes.
During this time, the Hot pump will
automatically work when it needs to in order
to keep your water hot.
3. For example, if the AMK-WB is in a
bathroom with only a sink, and you just want
to come into the room and want to use hot
water for 5 minutes (like for washing your
hands), then you would want to program the
AMK-WB for 5 minutes.
4. For example, say that the AMK-WB is in
your kitchen and you want to use hot water
for 5 minutes (to fill a pot) then not use hot
water for 15 minutes while preparing food.
Then you use hot water again for to clean
some dishes. If you keep cooking and using
hot water like this for one hour, then you
may want to program the AMK-WB for 60
minutes. During this time, the Hot pump will
automatically work when it needs to in order
to keep your water hot.
5. This time can be set by following steps 9 to
13 above in the Instructions for
Programming of the AMK-WB.
Changing the Battery:
1. When the Red lamp on the front of the
transmitter does not flash during operation,
then it is time to change the battery.
2. Slide open the battery cover on the back of
the transmitter. Remove the old battery and
replace it with a new lithium battery CR-
2032. Make sure that the positive side is
facing up. Slide the battery cover closed.