Aquatica Digital Millennium Vanity 900 MM User manual

Function : Form : Fashion
Millennium Vanity
Collection
Installation & Care Manual
Function : Form : Fashion

Aquaticausa.com
Aquaticabath.ca
E: [email protected]
Millennium
Vanity CollectionVanity Collection
900 MM
1200 MM
1520 MM
1800 MM
IMPORTANT - PLEASE READ BEFORE INSTALLATION
Please read these instructions carefully before starting the installation process and keep in a safe place
for future reference.
IMPORTANT: To reduce the risk of product damage, DO NOT modify the vanity. Doing so will compromise the
structural stability and void the warranty. This manual contains proper information on how to install the Guilder Collection.
NOTE: This series comes in several sizes however the installation procedures remain the same. Observe all local building
codes. Two people should install this product.
This vanity series needs specific site preparation. Do not install your vanity until all support framing and plumbing
rough-ins have been completed and wall surface is finished.
Secure the vanity to stud framing. When possible, provide 2x6 timber behind the finished wall for additional support.
To ease the installation process, remove the drawer from the vanity before installation. Refer to the section in this guide
for drawer removal.
This product should only be installed by a qualified professional plumber or contractor. If the installation is completed by a
non-qualified professional person, any product guarantee maybe considered invalid. Ensure the room is well heated and
ventilated.
WARNING: always check for any hidden pipes or electrical cables before drilling holes in the floor or walls. Do not over
tighten tap or waste fittings. Doing so may result in damaging the countersink.
Before installing a wooden bathroom product into a new property extension or recently plastered room we strongly advise
the building/room be completely dry, well ventilated, and adequately heated prior to installation.
Save these instructions for future use and reference. An improper installation voids the warranty. Installed vanities cannot be
returned. If you experience any problems with your vanity, contact our customer service team at [email protected].
TOOLS & EQUIPMENT
MANDATORY INSTALL PROCEDURE

Function : Form : Fashion
1
Pull out the drawer to its full extension by gently gripping
the release levers on both sides and pull the drawer
off the runners at the front.
3
To properly support the weight of the vanity and
countersink, secure to stud framing or 2x6 bracing
behind the finished wall.
When installing 2x6 bracing, front-notch the studs to
ensure the bracing sits flush against the studs.
The bracing should span the length of the vanity.
Consider for routing supply and drain piping for your
desired sink.
IMPORTANT: To ensure proper support and
alignment the finished wall must be straight and
plumb. Complete and finish the wall decoration or
tiling before vanity installation.
2
Plan Vanity Position
Decide on the position and height of the vanity.
The recommended sink height is 34” from the
finished floor to the top of the cabinet.
4
French Cleat Vanity Installation
Top cleat has been pre-attached to the vanity.
Installer must screw the bottom cleat to the wall.
34”
19”
32”
MANDATORY INSTALL PROCEDURE
Function : Form : Fashion
Top Cleat (pre-attached to vanity)
Bottom Cleat (need to screw to wall)
Stud
Drywall
Back panel
of vanity

Aquaticausa.com
Aquaticabath.ca
E: [email protected]
Millennium
Vanity CollectionVanity Collection
5
a: Carefully apply silicone to the top edges of the vanity.
b. Carefully position the basin down onto the vanity,
enusre it is centrally positioned and flush at the back.
Connect the faucet and drain in accordance with the
manufacturer’s instructions.
Apply silicone to the join between the worktop and wall,
down sides of the vanity and round the base of the
countersink. Let silicone dry for 24 hours.
6
Re-fit Drawers:
1. Pull drawer runners fully out.
2. Set the drawer down onto the runners.
3. Push the drawer fully in.
Test to make sure the drawers operate correctly and
there are no obstructions behind the drawer.
ab
DRAWER ADJUSTMENTS
FRONT side-to-side adjustment
Rotate side-to-side adjustment
left or right onboth locking devices.
Drawer front moves in the same
direction as rotation.
Maximum 1.5mm (1/16”) to left
or right (tool-free)
MANDATORY INSTALL PROCEDURE
CLEANING GUIDE
Millennium vanity units are designed to be easy to clean. After each use, simply wipe your vanity down with a soft cloth to
remove any surface dirt. Do not leave any standing water on your vanity.
For general cleaning, we recommend using warm water and a mild soap. Do not use abrasive products or cream cleaners
as these can damage the finish. Never use any petroleum-based products when cleaning like paint thinner or other such
solvents. They will damage the vanity.
To clean the Fireclay countersink, use a soft, dampened sponge or cloth and mild soapy water. Never use strong or
abrasive cleaners. Wipe surfaces clean immediately after applying cleaner. Never allow a cleaner to sit or soak.
Function : Form : Fashion
Function : Form : Fashion
REAR side-to-side adjustment
Rotate side-to-side adjustment
left or right on the rear hook of the
right hand runner.
Drawer front moves in the same
direction as rotation.
Maximum 1.5mm (1/16”) to left
or right (tool-free)
HEIGHT adjustment
Press up on adjustment
tab and push toward
back of drawer.
Maximum 3mm (1/8”) rise
of drawer front (tool-free)
TILT adjustment
Rotate the tilt adjustment
lever on the rear of each
runner to tilt the top of
the drawer front forward.
Maximum 5mm (3/16”) rise
of drawer back (tool-free)