arbane Active Audio iS AA Series User manual

iS AA Series
User manual

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A2 3
General information
iS AA Series - User manual
03/2023
Active Audio (Active Audio / Arbane Groupe)
8 Rue Johannes Gutenberg - 44340 Bouguenais- France
Tél : [phone]
www.activeaudio.fr
1. Safety note and general information 5
2. The iS range 7
2.1 Description of the product line 7
2.2 Product description 8
2.3 Connections 11
2.4 Amplifiers 12
2.5 Recommended equalization 13
2.6 Examples of configurations 15
2.7 Rigging 18
2.8 Maintenance - Spare parts 21
2.9 Technical specifications 24

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A4 5
1. Safety note and general information
• Information on the risk of exposure to high sound level
• Active Audio loudspeakers are liable to generate levels of sound pressure hazardous to health,
which may cause hearing impairment. It is recommended that you never stand in the immediate
vicinity of the loudspeakers in operation and wear hearing protection when necessary. Observe
the maximum exposure time to noise according to the noise level and the regulations in force in
your country. Pay attention to the hearing protection of listeners when using Active Audio systems.
• Read this manual before use and keep it.
• Read all documents relating to the product to be used before setting up and using it. Please
contact Active Audio with any questions relating to the product.
• Obtain the latest version of the user manual from the Active Audio website: www.activeaudio.fr
• Consider all warnings and follow the instructions and recommendations for use.
• Make sure you know the safety rules for hanging, stacking or setting up on a pole or tripod. Failure
to follow these rules may expose people to potential injury or death.
• Ensure the safety of operators and spectators.
• Staff must wear personal protective equipment (PPE) during each step of installing the product
(helmet, gloves, safety shoes at a minimum).
• Installation of Active Audio products should only be carried out by qualified staff trained in rigging
techniques and aware of the safety recommendations set out in this manual.
• Always check the stability, resistance to weight, flatness and horizontality of the support. Prevent
access to the spectators around the system, prevent it being possible to push or climb the stack
of speakers. Use straps to prevent tipping.
• Do not store the product on an unstable cart, stand, tripod, bracket or table.
• Use the products with the specified accessories by the manufacturer.
• Inspect lifting products and accessories before each use.
• Do not install equipment that is faulty or presents a risk of breakage and have it repaired by
qualified personnel or by Active Audio.
• Entrust all repairs to qualified staff or by Active Audio. Repairs are mandatory if the device is
damaged in any way, for example: damaged power cord or plug, spilled liquid or object dropped
inside the device, exposure of the device rain or moisture for long periods of time, appliance that
does not operate normally or that has been dropped.
• Any unauthorized maintenance operation will void the product warranty.
• Perform safety and compliance checks of accessories, enclosures, and third-party accessories
periodically at least once a year.
• Respect the maximum load capacity of each configuration.
• Use only with a cart, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. If a cart is used, move the cart-apparatus combination carefully so as not to tip it over,
which could cause personal injury.
• Do not install near a heat source such as an open flame, radiator, heat register, stove or any other
device that produces heat (including amplifiers).
• Do not expose the product to extreme conditions such as humidity (rain, sea water, condensation,
ambient humidity, etc.), excessive heat (sun, heating, etc.) over a long period.
• Take into account the effects of the wind. Flying loudspeakers overhead at wind forces higher
than, 16 mph (25km/h) is not recommended. If the wind force exceeds 46 mph (72km/h):
- Make sure that no person remains in the vicinity of the loudspeaker array.
- Lower and secure the array.
• During an outdoor performance, it is advisable to find out about the weather conditions and
to follow the local weather report and the recommendations of the competent authorities. An
anemometer can be used at the top of the system.

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A6 7
2. The iS range
2.1 Description of the product line
The Active Audio iS Series loudspeaker range is a range of subwoofers designed to extend the frequency response of Active
Audio column loudspeakers in the bass frequency.
iS Series is a range made up of 3 high quality bass speakers dedicated to professional installations.
Aesthetic and compact, they deliver a high sound level while offering high quality sound reproduction.
Designed for fixed installation, the iS Series loudspeakers have ergonomic options allowing them to be integrated easily and
quickly.
• Use a secondary safety system for any Active Audio speaker rigging.
• The product is intended for be used by professionals trained in professional audio work.
• Active Audio declines all responsibility in the event of the use of non-validated accessories or non-
compliance with safety instructions and rules.
• Active Audio products are guaranteed for 5 years. The full five-year warranty covers filters and
transducers against manufacturing defects under normal product use.
• Active Audio pursues a research and development policy aimed at improving its products. For
this reason, new materials, manufacturing methods and changes in principle may be introduced
without prior warning. As a result, an Active Audio product may differ in some aspects from its
published description, however, unless otherwise indicated, its characteristics will be greater than
or equal to those published.
• Disposal of electrical or electronic equipment
• This symbol on the product or on its packaging indicates that it will not be treated as household
waste. Instead it will be delivered to the applicable collection point for the recycling of electrical
and electronic equipment. By ensuring recycling, you will help prevent potential consequences
for the environment and human health. Recycling of materials will help conserve natural resources.
For more detailed information on recycling this product, please contact your local office, waste
collection agency or dealer.

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A8 9
2.2 Product description
iS110
The iS110 subwoofer has been designed to discreetly add
deep bass extension to the installation range loudspeakers.
The iS110 is equipped with a 10’’ loudspeaker loaded with
bass reflex on an inclined plane. This exclusive acoustic
design has the effect of greatly reducing load volumes in
order to achieve an optimal {size / low cutoff frequency} ratio
while gaining acoustic efficiency.
The iS110 is equipped with two SPEAKON NL4 connectors.
The frequency response extends from 45Hz to 180Hz.
It is very compact and can be positioned horizontally and
vertically for optimal visual integration. Indeed it is possible to
place it or fix it to the wall thanks to an optional fixing bracket
(iS110KMV). Embedded in a cutaway, the connectors are
protected and allow discreet wiring. It is naturally intended for
the bass extension of Ray-On and Step-Array type speakers.
The iS110 is available in a white or black version for even more
efficient integration.
In fixed installation, the compact dimensions of the iS110 allow
a non-obstructive arrangement in restricted environments and
can be perfectly integrated under small stages or platforms or
even under seats or benches. It is perfect for places like, for
example, small theatres, conference venues or themed bars.
To benefit from maximum performance and protection,
the iS110 must be used exclusively with the associated
loudspeaker preset, via an Active Audio integrated DSP
processor or amplifier or validated by the brand.
iS112
The iS112 model is a compact subwoofer dedicated to mobile
applications and small fixed installations. It is equipped with a
12” speaker.
Its acoustic design has the effect of significantly reducing
load volumes in order to obtain the lowest possible {size / low
cutoff frequency} ratio while gaining acoustic efficiency.
This dual loudspeaker loading with forward and reverse
volume also provides true mechanical control of diaphragm
travel and reduced distortion.
Ergonomically, the iS112 incorporates a screw base for
coupling tube, integrated and protected connectors, shock-
absorbing and non-slip pads.
The iS112 is equipped with two SPEAKON NL4 connectors.
In fixed installation, its reduced dimensions facilitate its
integration in restricted spaces, under small stages, platforms
or even benches.
The sound reproduction is characterized by a precise bass
from 45Hz translated by a beautiful sound impact and a lot of
musicality in the bass.
The iS112 combines perfectly with Ray-On and Step-
Array type speakers to form effective facade systems in
small concert venues, bars and small clubs, in conference
rooms. The ‘iS112BH’ accessory allows the subwoofer to be
suspended from the ceiling.
The iS112 will be appreciated by mobile systems in service
for its compactness and portability, especially in corporate
events. This subwoofer is also suitable for distributed sound
systems in installations.
To benefit from maximum performance and protection,
the iS112 must be used exclusively with the associated
loudspeaker preset, via an Active Audio processor or amplifier
with integrated DSP or validated by the brand.

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A10 11
iS115
The iS115 model is a compact format subwoofer serving both
in fixed installation and in service.
It is equipped with a 15’’ Neodymium loudspeaker, the
acoustic load being the bass-reflex.
This exclusive acoustic design has the effect of greatly
reducing load volumes in order to achieve an optimal {size /
low cutoff frequency} ratio while gaining acoustic efficiency.
This dual loudspeaker loading with forward and reverse
volume also provides true mechanical control of diaphragm
travel and reduced distortion.
Ergonomically, the iS115 integrates multiple functions: two
integrated handles, protected and discreetly fully recessed
connectors, a screw tube base and pads.
The Active Audio iS115 subwoofer is the only one in the
range equipped with a metal reinforcement of its M20 screw
tube base, which makes it the only one compatible with the
SA180PM free-standing accessory.
The iS115 is equipped with two SPEAKON NL4 connectors.
The iS115 is ideal in all applications where maximum power is
required with regard to its small size. It is naturally intended for
the bass extension of Step-Array speakers. In fixed installation,
the reduced dimensions of the iS115 allow a non-obstructive
arrangement in restricted environments and can be perfectly
integrated under small stages or platforms or even under
seats or benches. It is perfect for places such as theatres, small
concert venues, conference rooms, music bars or even small
clubs. As a mobile system, it is suitable for the sound system
of small concerts and events, in animation. This subwoofer
is also suitable for distributed sound reinforcement in large
spaces.
The ‘iS115BH’ accessory allows the subwoofer to be
suspended from the ceiling.
The iS115 works in the low frequencies from 40Hz and
provides a bass of great musicality and maximum precision.
For maximum performance and protection, the iS115 should
only be used with the associated loudspeaker preset, via an
Active Audio or brand-approved integrated DSP processor or
amplifier.
The rear panel of the iS Series subwoofers are equipped with two NL4 connectors. The four pins of the two connectors are
connected in parallel. The speakers occupy points 1 + / 1-.
The IN connector is used to receive the audio signal. The LINK connector allows it to be redistributed to another
iS subwoofer connected in parallel.
The internal pinout of the iS subwoofers is shown in the table below.
NL4 1+ 1- 2+ 2-
Rear panel connectors Hot (+) Cold (-) THRU THRU
IN LINK
Wiring
1+ Hot 2+ Thru
1- Cold 2- Thru
2.3 Connections

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A12 13
WARNING
Active Audio speakers must be powered by Active Audio or Powersoft amplifiers with the corresponding speaker preset.
Failure to observe this warning may cause damage to the components of the speakers and the user experience will not be
optimal.
MPA 4350 MPA 4700 MPA 41500
iS110 1/ ch. 1/ ch. 2/ ch.
iS112 1/ ch. 1/ ch. or 2/ ch.
iS115 1/ ch. or 2/ ch.
In order to maintain sound quality, the wiring will be carried out with flexible deoxyged-copper speaker cable with a minimum
2.5mm2 or 4mm2 section for lengths of up to 30 maximum for one speaker per channel.
Rec. minimum cable section [mm2] Rec. maximum cable length [m]
iS110 2.5mm235m
iS110 x 2 2.5mm215m
iS112 2.5mm235m
iS112 x 2 2.5mm215m
iS115 4mm235m
iS115 x 2 4mm215m
In the event that use with recall of the manufacturer preset is not possible (use of third-party processing and amplification
platforms). the filtering values in the table must be entered for each subwoofer.
CAUTION: The following values are for speaker equalization only. There is no protection. The only protection recommended
is that supplied with the factory preset. Active Audio declines all responsibility in the event of material breakage due to
overuse and non-use of manufacturer presets.
The attached table gives the recommended equalization and crossover settings for the iS Active Audio. The corresponding
response curves are in the figures on the next page.
iS110 iS112 iS115
High-pass filter freq (Hz) 46 42 40
High-pass filter gain (dB) -3 -3 -3
EQ1 freq (Hz) 42 46 46
EQ1 gain (dB) 3.5 3 5
EQ1 width (Oct) 0.3 0.5 0.5
EQ2 freq (Hz) 68 243 231
EQ2 gain (dB) -4 -12 -10
EQ2 width (Oct) 0.2 0.25 0.5
EQ3 freq (Hz) 310
EQ3 gain (dB) -9
EQ3 width (Oct) 0.45
High-shelf freq (Hz) 150
High-shelf gain (dB) -6
Low-pass filter freq (Hz) 180 180 180
Low-pass filter gain (dB) -3 -3 -3
Table : Loudspeakers / Amplifiers
parallel wiring recommendations
Table : Recommended cable section & length depending
on the configuration
2.4 Amplifiers 2.5 Recommended equalization

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A14 15
Two configurations between an iS115 subwoofer and a Step-Array 180 column loudspeaker are possible thanks to the
SA180PM accessory.
One in a standing configuration and the other in a suspended configuration.
2.6 Examples of configurations
Stand Mount (SA180PM-CC + SA180PM-BAR)
WARNING : Only the Active Audio iS115 subwoofer is compatible with the SA180PM accessory because the M20 screw
thread is reinforced from the inside. Do not use any other model of subwoofer, risk of breakage of the screw support. Do not
use an APG iS115 subwoofer that is not reinforced.
Take a TORX 25 screwdriver to unscrew/rescrew the screws
1
Caution: The M5 hexagonal
tamper-proof screw requires
a specific key.
Use an M5 hex tamper-proof
screw wrench
2
Be sure to
tighten the
SA180PM-
CC screws
securely
M5x10
M5x60
3
K&M 24521070-55
Bolt Adapter M8
EQ iS110 EQ iS112
EQ iS115
Unscrew the two M5
screws to remove the
connector cage
Attach SA180PM-CC in the same direction as the illustration
above.
Insert the adapter at the bottom of the SA180 enclosure allowing
use on a stand.

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A16 17
Suspension mount (SA180PM-CC + SA180PM-SUS)
Take a TORX 25 screwdriver to unscrew/tighten the screws.
1
Fix SA180PM-CC in the
same direction as the illus-
tration, then fix SA180PM-
SUS using the pin and lifting
ring
M5x10
M5x60
2
3
4Proceed with the SECURITY
CHECK to make sure that the pin
is correctly placed and that the
assembly is well fixed.
Proceed with the
SECURITY CHECK
to make sure that
the pin is correctly
placed and that
the assembly is
well fixed.
Total weight : 22kg

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A18 19
1. Place the mounting accessory on the underside of the enclosure then secure it using the M8x25 screws provided for this
purpose.
2. Use the lifting rings to suspend and secure the subwoofer with a motor for example.
1. It is possible to fix the assembly to a wall using the fixing holes. Fix the bracket to the support with plugs suitable for the
nature of the support, then install the subwoofer on the support.
2. To install the subwoofer on the support, simply fix it using the M8x25 screws provided for this purpose.
iS110 hanging accessory
The iS110 can be placed on the ground horizontally,
suspendedfromtheceilinghorizontallyorpositionedvertically
against a wall using the iS110KMV mounting accessory.
iS110KMV wall or ceiling mounting accessory
2.7 Rigging
4 x M8x25
Possibility to turn the
Active Audio logo in
the desired direction
Possibility to turn the
Active Audio logo in
the desired direction
Fixing holes for installation on a
suitable wall.
iS112 hanging accessory
The iS112 can be placed on the floor or suspended using the
iS112BH mounting accessory.
Hanging bumper iS112BH
4 x M8x25
Lifting rings

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A20 21
iS115 hanging accessory
The iS115 can be placed on the floor or suspended using the
iS115BH mounting accessory.
1. Place the mounting accessory on the underside of the speaker.
WARNING :
- For suspended use of the iS115, be sure to attach the bracket to the corresponding attachment points (A and A’) then
secure it using the M8x25 screws provided for this purpose.
Hanging bumper iS115BH
4 x M8x25
A A’
12
2. Use the lifting rings to suspend and secure the enclosure with a hoist for example.
Lifting rings
REPERE REFERENCE DESIGNATION
1 PRS_1261 Black steel iS110 AA
2 PRS_1262 White steel iS110 AA
3 PRS_1126 Recone kit for PST_1508
4 PRS_1195 HP PST_1508_completed
2.8 Maintenance - Spare parts
iS110 loudspeaker
12
3 4
Possibility to turn the
Active Audio logo in
the desired direction

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A22 23
REPERE REFERENCE DESIGNATION
1 PRS_1263 Black steel iS112 AA
2 PRS_1264 White steel iS112 AA
3 PRS_1198 Recone kit for PST_1524
4 PRS_1199 HP PST_1524_completed
iS112 loudspeaker
12
3 4
REPERE REFERENCE DESIGNATION
1 PRS_1265 Black steel iS115 AA
2 PRS_1266 White steel iS115 AA
3 PRS_1202 Recone kit for PST_1541
4 PRS_1203 HP PST_1541_completed
iS115 loudspeaker
12
3 4

User manual - iS AA Series User manual - iS AA Series
03/2023 03/2023DOP_1739_A DOP_1739_A24 25
2.9 Technical specifications
Features
Usable bandwidth (± 10 dB) 45 Hz - 180 Hz
SPL Max @ 1m 132 dB SPL (1)
Nominal directivity Omnidirectionnal (2)
Nominal impedance 8 ohms
Components
Transducers 1 x 10'' Ferrite
Topology Dual Interactive Chamber
Technology
Acoustical load Bass Reflex
Ways and amplification type 1 way, mono amplified
Power
AES 500 W (3)
Maximum power handling 2000 W (4)
Construction
Dimensions H,W,D (mm) 10,8’’ x 16,7’’ x 20’’
(275 x 425 x 510 mm)
Weight 41,8 lb
(19,2 kg)
Connectors 2 x Speakon NL4MP (5)
IP 43
Color White (RAL9016) or Black
(RAL9005)
(1) Peak level @ 1m, 2πsr using 12dB crest factor pink noise with
Active Audio preset
(2) Nominal directivity @-6dB
(3) Continuous power according to AES2-2012 in DCR
(4) Peak power according to AES2-2012 in DCR
(5) SPEAKON connectors are wired hot pin 1+, cold pin1- (2+ and
2- THRU)
iS110 loudspeaker
510,00
425,00
275
Features
Usable bandwidth (± 10 dB) 45 Hz - 180 Hz
SPL Max @ 1m 137 dB SPL (1)
Nominal directivity Omnidirectionnal (2)
Nominal impedance 8 ohms
Components
Transducers 1 x 12'' Néodyme
Topology Dual Interactive Chamber
Technology
Acoustical load Bass Reflex
Ways and amplification type 1 way, mono amplified
Power
AES 800 W (3)
Maximum power handling 3200 W (4)
Construction
Dimensions H,W,D (mm) 12,7’’ x 20,6’’ x 24’’
(325 x 525 x 610 mm)
Weight 53,1 lb
(24,1 kg)
Connectors 2 x Speakon NL4MP (5)
IP 43
Color White (RAL9016) or Black
(RAL9005)
(1) Peak level @ 1m, 2πsr using 12dB crest factor pink noise with
Active Audio preset
(2) Nominal directivity @-6dB
(3) Continuous power according to AES2-2012 in DCR
(4) Peak power according to AES2-2012 in DCR
(5) SPEAKON connectors are wired hot pin 1+, cold pin1- (2+ and
2- THRU)
iS112 loudspeaker
610,00
525,00
325,00

Arbane Groupe
8 Rue Johannes Gutenberg - 44340 Bouguenais- France
Tél : [phone]
www.apg.audio
User manual - iS AA Series
03/2023DOP_1739_A 26
Features
Usable bandwidth (± 10 dB) 42 Hz - 180 Hz
SPL Max @ 1m 138 dB SPL (1)
Nominal directivity Omnidirectionnal (2)
Nominal impedance 8 ohms
Components
Transducers 1 x 15'' Néodyme
Topology Dual Interactive Chamber
Technology
Acoustical load Bass Reflex
Ways and amplification type 1 way, mono amplified
Power
AES 900 W (3)
Maximum power handling 3600 W (4)
Construction
Dimensions H,W,D (mm) 14,7’’ x 23,5’’ x 27,1’’
(375 x 598 x 690 mm)
Weight 72 lb
(32,7 kg)
Connectors 2 x Speakon NL4MP (5)
IP 43
Color White (RAL9016) or Black
(RAL9005)
(1) Peak level @ 1m, 2πsr using 12dB crest factor pink noise with
Active Audio preset
(2) Nominal directivity @-6dB
(3) Continuous power according to AES2-2012 in DCR
(4) Peak power according to AES2-2012 in DCR
(5) SPEAKON connectors are wired hot pin 1+, cold pin1- (2+ and
2- THRU)
iS115 loudspeaker
690,00
598,00
375,00