arbane APG iS Series User manual

iS Series
User manual

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E2 3
General information
iS Series - User manual
03/2023 EN
APG France (Active Audio / Arbane Groupe)
8 Rue Johannes Gutenberg - 44340 Bouguenais- France
Tél : [phone]
www.apg.audio/en
1. Safety note and general information 5
2. The iS range 7
2.1 Description of the product line 7
2.2 Product description 8
2.3 Connections 11
2.4 Amplifiers 12
2.5 Examples of configurations 13
2.6 Rigging 16
2.7 Maintenance - Spare parts 21
2.8 Technical specifications 24
2.9 iS-O : iS Series special Outdoor 27

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E4 5
1. Safety note and general information
• Information on the risk of exposure to high sound level
• APG loudspeakers are liable to generate levels of sound pressure hazardous to health, which may
cause hearing impairment. It is recommended that you never stand in the immediate vicinity of the
loudspeakers in operation and wear hearing protection when necessary. Observe the maximum
exposure time to noise according to the noise level and the regulations in force in your country.
Pay attention to the hearing protection of listeners when using APG systems.
• Read this manual before use and keep it.
• Read all documents relating to the product to be used before setting up and using it. Please
contact APG with any questions relating to the product.
• Obtain the latest version of the user manual from the APG website: www.apg.audio .
• Consider all warnings and follow the instructions and recommendations for use.
• Make sure you know the safety rules for hanging, stacking or setting up on a pole or tripod. Failure
to follow these rules may expose people to potential injury or death.
• Ensure the safety of operators and spectators.
• Staff must wear personal protective equipment (PPE) during each step of installing the product
(helmet, gloves, safety shoes at a minimum).
• Installation of APG products should only be carried out by qualified staff trained in rigging
techniques and aware of the safety recommendations set out in this manual.
• Always check the stability, resistance to weight, flatness and horizontality of the support. Prevent
access to the spectators around the system, prevent it being possible to push or climb the stack
of speakers. Use straps to prevent tipping.
• Do not store the product on an unstable cart, stand, tripod, bracket or table.
• Use the products with the specified accessories by the manufacturer.
• Inspect lifting products and accessories before each use.
• Do not install equipment that is faulty or presents a risk of breakage and have it repaired by
qualified personnel or by APG.
• Entrust all repairs to qualified staff or by APG. Repairs are mandatory if the device is damaged in
any way, for example: damaged power cord or plug, spilled liquid or object dropped inside the
device, exposure of the device rain or moisture for long periods of time, appliance that does not
operate normally or that has been dropped.
• Any unauthorized maintenance operation will void the product warranty.
• Perform safety and compliance checks of accessories, enclosures, and third-party accessories
periodically at least once a year.
• Respect the maximum load capacity of each configuration and carry out conformity simulations
using the tools APG Tools, APG Uniline Aiming Tool, AFMG EASE Focus 3.
• Use only with a cart, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. If a cart is used, move the cart-apparatus combination carefully so as not to tip it over,
which could cause personal injury.
• Do not install near a heat source such as an open flame, radiator, heat register, stove or any other
device that produces heat (including amplifiers).
• Do not expose the product to extreme conditions such as humidity (rain, sea water, condensation,
ambient humidity, etc.), excessive heat (sun, heating, etc.) over a long period.
• Take into account the effects of the wind. Flying loudspeakers overhead at wind forces higher
than, 16 mph (25km/h) is not recommended. If the wind force exceeds 46 mph (72km/h):
- Make sure that no person remains in the vicinity of the loudspeaker array.
- Lower and secure the array.
• During an outdoor performance, it is advisable to find out about the weather conditions and
to follow the local weather report and the recommendations of the competent authorities. An
anemometer can be used at the top of the system.

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E6 7
• Use a secondary safety system for any APG speaker rigging.
• The product is intended for be used by professionals trained in professional audio work.
• APG declines all responsibility in the event of the use of non-validated accessories or non-
compliance with safety instructions and rules.
• APG products are guaranteed for 5 years. The full five-year warranty covers filters and transducers
against manufacturing defects under normal product use.
• APG pursues a research and development policy aimed at improving its products. For this reason,
new materials, manufacturing methods and changes in principle may be introduced without prior
warning. As a result, an APG product may differ in some aspects from its published description,
however, unless otherwise indicated, its characteristics will be greater than or equal to those
published.
• Disposal of electrical or electronic equipment
• This symbol on the product or on its packaging indicates that it will not be treated as household
waste. Instead it will be delivered to the applicable collection point for the recycling of electrical
and electronic equipment. By ensuring recycling, you will help prevent potential consequences
for the environment and human health. Recycling of materials will help conserve natural resources.
For more detailed information on recycling this product, please contact your local office, waste
collection agency or dealer.
2. The iS range
2.1 Description of the product line
iS Series is a range made up of 3 high-quality bass speakers dedicated to professional installations.
Aesthetic and compact, they deliver a high sound level while offering a high quality of sound reproduction.
Designed for fixed installation, the iS Series speakers feature ergonomic options for quick and easy integration.

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E8 9
2.2 Product description
iS110
The iS110 subwoofer has been designed to add a deep
bass extension to the speakers of the installation range while
discreetly.
The iS110 is equipped with a 10’’ speaker loaded with bass
reflex. This exclusive acoustic design has the effect of greatly
reducing the load volumes in order to achieve an optimal
{size / low cutoff frequency} ratio while improving acoustic
efficiency.
The iS110 is equipped with two SPEAKON NL4 connectors.
The frequency response ranges from 45Hz to 150Hz.
It is very compact and can be positioned horizontally and
vertically for optimal visual integration in fact it is possible
to arrange it or fix it to the wall using optional fixing brackets
(iS110KMV). Embedded in a cutaway, the connections are
protected and allow discreet wiring. It is naturally intended
for the bass extension of iX and DX speakers. The iS110 is
available in white or black for even more efficient integration.
In a fixed installation, the compact dimensions of the
iS110 allow a non-obstructive arrangement in restricted
environments and can fit perfectly under small stages or
podiums or even under seats or benches. It is perfect for
places like, for example, small theaters, conference venues or
themed bars.
iS112
The iS112 is a compact subwoofer dedicated to mobile
applications and small-scale fixed installations. It is equipped
with a 12’’ speaker.
Its acoustic design has the effect of considerably reducing the
load volumes in order to obtain the lowest possible {size / low
cutoff frequency} ratio while improving acoustic efficiency.
This dual speaker load with front and rear volume also
provides true mechanical control of diaphragm travel and
reduced distortion.
Ergonomically, the iS112 incorporates a screw base for
coupling tube, integrated and protected connectors, damping
and non-slip pads.
The iS112 is equipped with two SPEAKON NL4 connectors.
In a fixed installation, its reduced dimensions facilitate its
integration in confined spaces, under small stages, platforms
or even benches.
The sound reproduction is characterized by a precise bass
from 45Hz translated by a beautiful sound impact and a lot of
musicality in the bass.
The iS112 pairs perfectly with iX and DX loudspeakers to
provide effective front panel systems in small concert venues,
bars and clubs, and conference rooms.
The iS112 will be appreciated by service delivery mobile
systems for its compactness and portability, especially
for corporate events. This subwoofer is also suitable for
distributed sound in an installation. The impact sound
rendering and dynamics of the iS112 make it effective
for “drum fill” applications on small stages. For maximum
performance and protection, the iS112 should only be used
with an APG processor and amplifier.

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E10 11
iS115
The iS115 model is a compact subwoofer suitable for both
fixed installation and service.
It is equipped with a 15’’ neodymium speaker, the acoustic
load being the bass reflex.
This exclusive acoustic design has the effect of greatly
reducing the load volumes in order to achieve an optimal
{size / low cutoff frequency} ratio while improving acoustic
efficiency. This dual speaker load with front and rear volume
also provides true mechanical control of diaphragm travel
and reduced distortion.
At the ergonomic level, the iS115 integrates multiple
functions: two integrated handles, a fully recessed protected
and discreet connection, a screw tube base and glides.
The iS115 is equipped with two SPEAKON NL4 connectors.
The iS115 is ideal for all applications where maximum power
is desired with regard to its small footprint. It is naturally
intended for the bass extension of DX speakers and goes very
well with the Uniline Compact in a reduced configuration. In a
fixed installation, the reduced dimensions of the iS115 allow a
non-obstructive arrangement in restricted environments and
can be perfectly integrated under small stages or podiums or
even under seats or benches. It is perfect for places such as
theaters, small concert venues, conference rooms, music bars
or even small clubs.
In mobile system it is suitable for the sound of small concerts
and events, in animation. This subwoofer is also suitable for
distributed sound in large spaces.
The hanging options allow it to be fixed to the ceiling with
the possibility of coupling with DX12 or DX15 speakers. With
these same speakers, in on-stage mode, it makes it possible to
constitute a compact and very efficient “drum fill” type system.
The iS115 works in low frequencies from 40Hz and provides
a bass of great musicality and maximum precision even in
adverse acoustics. For maximum performance and protection,
the iS115 should only be used with an APG processor and
amplifier.
The rear panel of the iS Series subwoofers are equipped with two NL4 connectors. The four pins of the two connectors are
connected in parallel. The speakers occupy points 1 + / 1-.
The IN connector is used to receive the audio signal. The LINK connector allows it to be redistributed to another
iS subwoofer connected in parallel.
The internal pinout of the iS subwoofers is shown in the table below.
NL4 1+ 1- 2+ 2-
Rear panel connectors Hot (+) Cold (-) THRU THRU
IN LINK
Wiring
1+ Hot 2+ Thru
1- Cold 2- Thru
2.3 Connections

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E12 13
WARNING
APG speakers must be powered by APG or Powersoft amplifiers with the corresponding speaker preset. Failure to heed
this warning may cause damage to speaker components and the user experience will not be optimal. Refer to the amplifier
manual fot its connection to the speakers.
DA8 DA12
iS110 8 8
iS112 8 8
iS115 8 8
In order to maintain sound quality, the wiring will be carried out with flexible deoxyged-copper speaker cable with a minimum
2.5mm2 or 4mm2 section for lengths of up to 30 maximum for one speaker per channel.
Rec. minimum cable section [mm2] Rec. maximum cable length [m]
iS110 2.5mm235m
iS110 x 2 2.5mm215m
iS112 2.5mm235m
iS112 x 2 2.5mm215m
iS115 4mm235m
iS115 x 2 4mm215m
Table : Loudspeakers / Amplifiers
parallel wiring recommendations
Table : Recommended cable section & length depending
on the configuration
2.4 Amplifiers 2.5 Examples of configurations
2 x iX5
2 x iS110
1 x DA8
2 x iX6
2 x iS112
1 x DA8

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E14 15
2 x iX8
2 x iS115
1 x DA8
2 x iX12
2x iS115 au sol
1 x DA12
2 x iX12
2 x iS115 suspendu
1 x DA12

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E16 17
iS110 hanging accessory
The iS110 can be placed on the floor horizontally, or
positioned vertically against a wall with the iS110KMV
mounting accessory.
1. Place the mounting accessory on the underside of the enclosure then secure it using the M8x25 screws provided for this
purpose.
2. If necessary, it is possible to fix the assembly on a section of wall using the fixing holes.
iS110KMV wall or ceiling mounting accessory
2.6 Rigging
4 x M8x25
Fixing holes for installation on a
wall
1. Place the mounting accessory on the underside of the enclosure then secure it using the M8x25 screws provided for this
purpose.
2. Use the lifting rings to suspend and secure the subwoofer with a motor for example.
iS112 hanging accessory
The iS112 can be placed on the floor or suspended using the
iS112BH mounting accessory.
Hanging bumper iS112BH
4 x M8x25
Lifting rings

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E18 19
iS115 hanging accessory
The iS115 can be placed on the floor or suspended using the
iS115BH mounting accessory.
1. Place the mounting accessory on the underside of the speaker.
WARNING :
- For use alone, be sure to secure the hanging bumper to the corresponding attachment points (A and A ’) then secure it
using the M8x25 screws provided for this purpose.
- For use with iX12 loudspeaker, be sure to secure the hanging bumper to the attachment points (B and B ’) then fix it using
the M8x25 screws provided for this purpose.
Hanging bumper iS115BH
4 x M8x25
4 x M8x25
Use alone
Use with iX12 loudspeaker
A
B
A’
B’
1
1
2
2
2. Use the lifting rings to suspend and secure the subwoofer with a motor for example.
Lifting rings

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E20 21
iS115 to iX12 connection accessory
The iS115 also has an LS115-iX12 junction piece allowing
coupling with an iX12.
1. Place the iX12 loudspeaker horizontally and fix the junction pieces on each side of the iX12.
2. Assemble by approaching the iX12 under the iS115 then fix the junction pieces to the iS115 using the M8x25 screws.
Connection accessory LKiS115-iX12
4 x M8x25
123
REPERE REFERENCE DESIGNATION
1 PRS_1193 Black steel iS110
2 PRS_1194 White steel iS110
3 PRS_1126 Recone kit for PST_1508
4 PRS_1195 HP PST_1508_completed
2.7 Maintenance - Spare parts
iS110 loudspeaker
12
3 4

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E22 23
REPERE REFERENCE DESIGNATION
1 PRS_1196 Black steel iS112
2 PRS_1197 White steel iS112
3 PRS_1198 Recone kit for PST_1524
4 PRS_1199 HP PST_1524_completed
iS112 loudspeaker
12
3 4
REPERE REFERENCE DESIGNATION
1 PRS_1200 Black steel iS115
2 PRS_1201 White steel iS115
3 PRS_1202 Recone kit for PST_1541
4 PRS_1203 HP PST_1541_completed
iS115 loudspeaker
12
3 4

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E24 25
2.8 Technical specifications
Features
Usable bandwidth (± 10 dB) 45 Hz - 150 Hz
SPL Max @ 1m 132 dB SPL (1)
Nominal directivity Omnidirectionnal (2)
Nominal impedance 8 ohm
Components
Transducers 1 x 10'' Ferrite
Topology Dual Interactive Chamber
Technology
Acoustical load Bass Reflex
Ways and amplification type 1 way, mono amplified
Power
AES 500 W (3)
Maximum power handling 2000 W (4)
Construction
Dimensions H,W,D (mm) 10,8’’ x 16,7’’ x 20’’
(275 x 425 x 510 mm)
Weight 41,8 lb
(19,2 kg)
Connectors 2 x Speakon NL4MP (5)
IP 43
(1) Peak level @ 1m, 2πsr using 12dB crest factor pink noise with
APG preset
(2) Nominal directivity @-6dB
(3) Continuous power according to AES2-2012 in DCR
(4) Peak power according to AES2-2012 in DCR
(5) SPEAKON connectors are wired hot pin 1+, cold pin1- (2+ and
2- THRU)
iS110 loudspeaker
510,00
425,00
275
Features
Usable bandwidth (± 10 dB) 45 Hz - 150 Hz
SPL Max @ 1m 137 dB SPL (1)
Nominal directivity Omnidirectionnal (2)
Nominal impedance 8 ohm
Components
Transducers 1 x 12'' ND
Topology Dual Interactive Chamber
Technology
Acoustical load Bass Reflex
Ways and amplification type 1 way, mono amplified
Power
AES 800 W (3)
Maximum power handling 3200 W (4)
Construction
Dimensions H,W,D (mm) 12,7’’ x 20,6’’ x 24’’
(325 x 525 x 610 mm)
Weight 53,1 lb
(24,1 kg)
Connectors 2 x Speakon NL4MP (5)
IP 43
(1) Peak level @ 1m, 2πsr using 12dB crest factor pink noise with
APG preset
(2) Nominal directivity @-6dB
(3) Continuous power according to AES2-2012 in DCR
(4) Peak power according to AES2-2012 in DCR
(5) SPEAKON connectors are wired hot pin 1+, cold pin1- (2+ and
2- THRU)
iS112 loudspeaker
610,00
525,00
325,00

User manual - iS Series User manual - iS Series
03/2023 03/2023DOP_1457_E DOP_1457_E26 27
Features
Usable bandwidth (± 10 dB) 42 Hz - 120 Hz
SPL Max @ 1m 138 dB SPL (1)
Nominal directivity Omnidirectionnal (2)
Nominal impedance 8 ohm
Components
Transducers 1 x 15'' ND
Topology Dual Interactive Chamber
Technology
Acoustical load Bass Reflex
Ways and amplification type 1 way, mono amplified
Power
AES 900 W (3)
Maximum power handling 3600 W (4)
Construction
Dimensions H,W,D (mm) 14,7’’ x 23,5’’ x 27,1’’
(375 x 598 x 690 mm)
Weight 72 lb
(32,7 kg)
Connectors 2 x Speakon NL4MP (5)
IP 43
(1) Peak level @ 1m, 2πsr using 12dB crest factor pink noise with
APG preset
(2) Nominal directivity @-6dB
(3) Continuous power according to AES2-2012 in DCR
(4) Peak power according to AES2-2012 in DCR
(5) SPEAKON connectors are wired hot pin 1+, cold pin1- (2+ and
2- THRU)
iS115 loudspeaker
690,00
598,00
375,00
2.9 iS-O : iS Series special Outdoor
IP54 loudspeakers
Cabinet For the cabinet, APG uses exclusively Baltic birch plywood treated with a polyurethane coating
against humidity and splashing water. This coating offers better resistance to UV as well as to
humid environments.
Steel Anti-corrosion treated steel, water resistant.
Accessries Water resistant stainless steel fixing bracket and screws.
Componants Waterproof treatment on the speaker membranes.
Connectors Cable gland connectors as standard for iS-O range. Speakon connectors are available on
specific request.

Arbane Groupe
8 Rue Johannes Gutenberg - 44340 Bouguenais- France
Tél : [phone]
www.apg.audio