arcelik 191641EI User manual

Refrigerator
User Manual
191641EI
58 5821 0000/ EN/ AK/ 02/08/2022 15:34
7285520143

EN / 2
Table of Content
1 Safety Instructions ........................ 4
1.1 Intention of Use ........................... 4
1.2 Safety of Children, Vulnerable
Persons and Pets ........................
4
1.3 Electrical Safety........................... 5
1.4 Handling Safety ........................... 6
1.5 Installation Safety ........................ 6
1.6 Operational Safety....................... 7
1.7 Food Storage Safety.................... 9
1.8 Maintenance and Cleaning
Safety ..........................................
10
1.9 Lighting ........................................ 11
2 Environmental Instructions .......... 11
2.1 Compliance with WEEE regula-
tions and Waste Disposal ............
11
2.2 Packaging Information................. 11
3 Your Refrigerator .......................... 12
4 Installation ..................................... 13
4.1 Electrical Connection................... 14
5 Preparation .................................... 15
5.1 What To Do For Energy Saving... 15
5.2 First Use ...................................... 16
5.3 Climate Class and Definitions...... 16
6 Operating the Product .................. 16
7 Control Panel of the Product ....... 17
8 Using The Product ........................ 19
8.1 Replacing the Illumination Lamp . 21
8.2 Door Open Alert........................... 21
9 Product Features .......................... 22
9.1 The ice storage area.................... 22
9.2 Crisper Technologies................... 22
9.3 Dairy Products Cold Storage
Area .............................................
22
10 Maintenance and Cleaning .......... 22
11 Troubleshooting ............................ 23

EN / 3

EN / 4
1 Safety Instructions
• This section includes the
safety instructions necessary
to prevent the risk of personal
injury or material damage.
• Our company shall not be held
responsible for damages that
may occur if these instructions
are not observed.
Installation and repair operations
shall always be performed by au-
thorized service.
Use original spare parts and ac-
cessories only.
Do not repair or replace any com-
ponent of the product unless it is
clearly specified in the user
manual.
Do not perform any modifications
on the product.
1.1 Intention of Use
• This product is not suitable for
commercial use and should
not be used for a purpose
other than its intended use.
• This product is intended for op-
erating interiors, such as
households or similar.
For example;
In the staff kitchens of the
stores, offices and other working
environments,
In farm houses,
In the units of hotels, motels or
other resting facilities that are
used by the customers,
In hostels, or similar environ-
ments,
In catering services and similar
non-retail applications.
• This product shall not be used
in open or enclosed external
environments such as vessels,
camper vans, balconies or ter-
races. Exposing the product to
rain, snow, sunlight and wind
may cause risk of fire.
1.2 Safety of Children,
Vulnerable Persons
and Pets
• This product may be used by
children aged 8 years and
older and persons with under-
developed physical, sensory or
mental capabilities or lack of
experience and knowledge if
they are being supervised or
have been given instruction
concerning use of the appli-
ance in a safe way and the
hazards involved.
• Children between 3 and 8
years are allowed to put and
take out food into/from the
cooler product.

EN / 5
• Electrical products are danger-
ous for children and pets. Chil-
dren and pets must not play
with, climb on, or enter the
product.
• Cleaning and user mainten-
ance should not be performed
by children unless there is
someone overseeing them.
• Keep the packaging materials
away from children. Risk of in-
jury and suffocation.
Before disposing of old products
that shall not be used any more:
1. Unplug the power cord from
the mains socket.
2. Cut the power cable and re-
move it from the appliance
together with the plug.
3. Do not remove the racks and
drawers from the product to
prevent children from getting
inside the appliance.
4. Remove the doors.
5. Store the product so that it
shall not be tipped over.
6. Do not allow children to play
with the scrapped product.
• Do not dispose of the product
by throwing it into fire. Risk of
explosion.
• If there is a lock available on
the product’s door, keep the
key out of children's reach.
1.3 Electrical Safety
• The product shall not be
plugged into the outlet during
installation, maintenance,
cleaning, repair, and transport-
ation operations.
If the power cable is damaged, it
shall only be replaced by author-
ized service to avoid any risks
that may occur.
• Do not tuck the power cable
under the product or to the
rear of the product. Do not put
heavy items on the power
cable. The power cable should
not be bent, crushed, and
come into contact with any
heat source.
• Do not use an extension cord,
multi-plug or adaptor to oper-
ate your product.
• Portable multi-plugs or port-
able power supplies may over-
heat and cause fire. Thus, do
not have a multi-plug, portable
power sources behind or in the
vicinity of the product.
• Do not plug the product’s
power cord in a loose or dam-
aged power outlet. These
types of connections may
overheat and cause fire.
• The plug shall be easily ac-
cessible. If this is not possible,
a mechanism that meets the
electrical legislation and that
disconnects all terminals from

EN / 6
the mains (fuse, switch, main
switch, etc.) shall be available
on the electrical installation.
• Do not touch the plug with wet
hands.
• When unplugging the appli-
ance, don’t hold the power
cord, but the plug.
1.4 Handling Safety
• This product is heavy, do not
handle it by yourself.
• Do not hold the product from
its door while handling the
product.
• Be careful not to damage the
cooling system and the pipes
while handling the product. Do
not operate the product if the
pipes are damaged, and con-
tact an authorized service.
1.5 Installation Safety
• Contact the Authorized Service
for the product's installation.
To prepare the product for use,
see the information in the user
manual and make sure the
electric and water utilities are
as required. If not, call a quali-
fied electrician and plumber to
arrange the utilities as neces-
sary. Failure to do so may res-
ult in electric shock, fire, prob-
lems with the product, or in-
jury.
• Check for any damage on the
product before installing it. Do
not have the product installed
if it is damaged.
• Place the product on a clean,
level and hard surface and bal-
ance it with the adjustable
legs. Otherwise, the refriger-
ator may tip over and cause in-
juries.
• The product shall be installed
in a dry and ventilated environ-
ment. Do not keep carpets,
rugs or similar covers under
the product. This may cause
risk of fire as a result of inad-
equate ventilation!
• Do not block or cover ventila-
tion holes. Otherwise, power
consumption increases and
your product may be dam-
aged.
• The product must not be con-
nected to supply systems such
as solar power supply. Other-
wise, your product may be
damaged due to sudden
voltage changes!
• The more refrigerant a refriger-
ator contains, the bigger its in-
stallation room should be. In
very small rooms, a flammable
gas-air mixture may occur in
case of a gas leak in the cool-
ing system. At least 1 m³ of
volume is required for each 8
grams of refrigerant. The

EN / 7
amount of the refrigerant avail-
able in your product is spe-
cified in the Type Label.
• The installation place of the
product shall not be exposed
to direct sunlight and it shall
not be in the vicinity of a heat
source such as stoves, radiat-
ors, etc. If you cannot prevent
installation of the product in
the vicinity of a heat source,
use a suitable insulation plate
and make sure the minimum
distance to the heat source is
as specified below:
– At least 30 cm away from
heat sources such as
stoves, ovens, heating units
and heaters, etc.,
– And at least 5 cm away from
electrical ovens.
• Your product has the protec-
tion class of I.
• Plug the product in a grounded
socket that conforms with the
Voltage, Current and Fre-
quency values specified in the
type label. The socket must
have a 10A – 16A fuse. Our
firm will not assume responsib-
ility for any damages due to
usage without earthing and
without power connection in
compliance with local and na-
tional regulations.
• The product’s power cable
must be unplugged during in-
stallation. Otherwise, risk of
electric shock and injury may
occur!
• Do not plug the product’s
power cord in loose, dislo-
cated, broken, dirty, oily power
outlets which have a risk of
water contact. These types of
connections may cause over-
heating and fire.
• Place the power cable and
hoses (if any) of the product so
that they shall not cause a risk
of tripping over.
• Penetration of humidity and li-
quid to live parts or to the
power cord may cause short
circuit. Thus, do not use the
product in humid environments
or in areas where water may
splash (e.g. garage, laundry
room, etc.) If the refrigerator is
wet by water, unplug it and
contact an authorized service.
• Do not ever connect your refri-
gerator to power saving
devices. These systems are
harmful for the product
1.6 Operational Safety
• Do not ever use chemical
solvents on the product. These
materials contain an explosion
risk.

EN / 8
• In case of a failure of the
product, unplug it and do not
operate until it is repaired by
the authorized service. There
is a risk of electric shock!
• Do not place a source of flame
(e.g. candles, cigarettes, etc.)
on the product or in the vicinity
of it.
• Do not get on the product. Risk
of falling and injury!
• Do not cause damage to the
pipes of the cooling system us-
ing sharp and piercing tools.
The refrigerant that sprays out
in case of puncturing the gas
pipes, pipe extensions or up-
per surface coatings may
cause irritation of skin and in-
jury to the eyes.
• Do not place and operate elec-
trical appliances inside the re-
frigerator/freezer unless it is
advised by the manufacturer.
• Do not jam any parts of your
hands or your body to the
moving parts inside the
product. Be careful to prevent
jamming of your fingers
between the refrigerator and
its door. Be careful while open-
ing or closing the door if there
are children around.
• Do not put ice cream, ice
cubes or frozen food to your
mouth as soon as you take
them out of the freezer. Risk of
frostbite!
• Do not touch the inner walls,
metal parts of the freezer or
food kept inside the freezer
with wet hands. Risk of frost-
bite!
• Do not place soda cans or
cans and bottles that contain
fluids that may be frozen to the
freezer compartment. Cans or
bottles may explode. Risk of
injury and material damage!
• Do not use or place materials
sensitive against temperature
such as flammable sprays,
flammable objects, dry ice or
other chemical agents in the
vicinity of the refrigerator. Risk
of fire and explosion!
• Do not store explosive materi-
als such as aerosol cans with
flammable materials inside the
product.
• Do not place cans containing
fluids over the product an open
state. Splashing of water on an
electrical part may cause the
risk of an electric shock or a
fire.
• This product is not intended for
storage and cooling of medi-
cines, blood plasma, laborat-
ory preparations or similar ma-
terials and products that are
subject to the Medical
Products Directive.

EN / 9
• If the product is used against
its intended purpose, it may
cause damage to or deteriora-
tion of the products kept in-
side.
• If your refrigerator is equipped
with blue light, do not look at
this light with optical devices.
Do not stare directly at UV
LED light for a long time. Ultra-
violet rays may cause eye
strain.
• Do not fill the product with
more food than its capacity. In-
juries or damages may occur if
the contents of the refrigerator
fall when the door is opened.
Similar problems may also oc-
cur when an object is placed
over the product.
• Ensure that you have removed
any ice or water that may have
fallen to the floor to prevent in-
juries.
• Change the locations of the
racks/bottle racks on the door
of your refrigerator only when
the racks are empty. Danger of
injury!
• Do not place objects that may
fall/tip over on the product.
These objects may fall while
opening or closing the door
and cause injuries and/or ma-
terial damages.
• Do not hit or exert excessive
pressure on glass surfaces.
Broken glass may cause injur-
ies and/or material damages.
• The cooling system in your
product contains R600a refri-
gerant. The refrigerant type
used in the product is specified
in the type label. This gas is
flammable. Therefore, be care-
ful not to damage the cooling
system and the pipes while op-
erating the product. In case of
damage to the pipes;
1. Do not touch the product or
the power cable.
2. Keep the product away from
potential sources of fire that
may cause the product to
catch fire.
3. Ventilate the area where the
product is placed. Do not use
a fan.
4. Contact Authorized Service.
5. If the product is damaged
and you observe gas leak,
please stay away from the
gas. Gas may cause frostbite
if it contacts your skin.
1.7 Food Storage
Safety
Please pay attention to the fol-
lowing warnings to avoid food
spoilage:
• Leaving the doors open for a
long time may cause the tem-
perature inside the product to
rise.
• Regularly clean the accessible
drainage systems in contact
with food.

EN / 10
• Clean the water tanks that
have not been used for 48
hours and mains-fed water
systems that have not been
used for more than 5 days.
• Store raw meat and fish
products in appropriate com-
partments within the product.
Thus, it does not drip on or
come into contact with other
foods.
• Two-star freezer compart-
ments are used for storing pre-
filled foods, making and storing
ice and ice cream.
• One, two and three-star com-
partments are not appropriate
for freezing fresh food.
• If the cooling product has been
left empty for a long time, turn
off the product, defrost, clean,
and dry the product in order to
protect the housing of the
product.
1.8 Maintenance and
Cleaning Safety
• Unplug the refrigerator before
cleaning it or starting to per-
form maintenance.
• Do not pull by the door handle
if you shall move the product
for cleaning purposes. Handle
may cause injuries if it is pulled
too hard.
• Do not put your hands etc. un-
der the refrigerator. Jamming
may occur or any sharp edge
may cause personal injuries.
• Do not clean the product by
spraying or pouring water on
the product and inside the
product. Risk of electric shock
and fire.
• When cleaning the product, do
not use sharp and abrasive
tools or household cleaning
agents, detergent, gas, gasol-
ine, thinner, alcohol, varnish,
and similar substances. Use
only cleaning and maintenance
agents that are not harmful for
food inside the product.
• Do not ever use steam or
steamed cleaning materials for
cleaning the product and thaw-
ing the ice inside it. Steam
contacts the live areas in your
refrigerator and causes short
circuit or electric shock.
• Take care to keep water away
from the ventilation holes,
electronic circuits or lighting of
the product.
• Use a clean, dry cloth to wipe
the dust or foreign material on
the tips of the plugs. Do not
use a wet or damp piece of
cloth to clean the plug. Other-
wise, risk of fire or electric
shock may occur.

EN / 11
1.9 Lighting • Contact an authorized service
when the LED / bulb used for
lighting has to be replaced.
2 Environmental Instructions
2.1 Compliance with WEEE regula-
tions and Waste Disposal
This product does not contain hazardous
and prohibited substances specified in the
"Regulations for Supervision of Waste Elec-
trical and Electronic Equipment" published
by Turkish Ministry of Environment and
Urban Planning.
Complies with WEEE Regula-
tion. This product was manu-
factured from recyclable and
reusable high quality parts and
materials. Therefore, do not
dispose of this product with
other domestic wastes at the
end of its life cycle. Take it to a collection
point for electrical and electronic equip-
ment. Please ask your local authorities re-
garding these collection areas. You can
help protect the environment and natural
resources by delivering the used products
for recycling.
2.2 Packaging Information
The product's packaging is made of
recyclable materials, in accordance
with the National Legislation. Do
not dispose of the packaging waste
with the household waste or other
wastes, dispose it to the packaging
collection areas specified by local
authorities.

EN / 12
3 Your Refrigerator
12
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1 Freezer Compartment 2 Cooler compartment
3 Fan 4 *Cooler compartment door shelves
5 Egg holder 6 Water dispenser filling tank
7 *Cooler compartment door shelves 8 Water dispenser reservoir
9 *Cooler compartment glass shelves 10 *Bottle shelf
11 *Cooler compartment door shelves 12 *Dairy (cold storage) bin
13 *Crispers 14 *Bottle shelf
15 *Crispers 16 Adjustable legs
17 Frozen food storing compartments 18 *Freezer compartment glass shelves
19 Icematic 20 Freezer compartment door shelves
*Optional: Figures in this user manual are
schematic and may not exactly match your
product. If your product does not comprise
the relevant parts, the information pertains
to other models.

EN / 13
4 Installation
Right place for installation
Read the “Safety Instructions” sec-
tion first!
Your product requires adequate air circula-
tion to function efficiently. If the product will
be placed in an alcove, remember to leave
at least 5 cm clearance between the
product and the ceiling, rear wall and the
side walls. Check if the rear wall clearance
protection component is present at its loca-
tion (if provided with the product). If the
component is not available, or if it is lost or
fallen, position the product so that at least 5
cm clearance shall be left between the rear
surface of the product and the wall of the
room. The clearance at the rear is import-
ant for efficient operation of the product.
Do not use extension or multi sock-
ets in the power connection.
The manufacturer assumes no re-
sponsibility for any damage caused
by the work carried out by unau-
thorized persons.
The product’s power cable must be
unplugged during installation. Fail-
ure to do so may result in death or
serious injuries!
If the door span is too narrow for
the product to pass, remove the
door and turn the product side-
ways; if this does not work, contact
the authorized service.
• Place the product on a flat surface to
avoid vibration
• Place the product at least 30 cm away
from the heater, stove and similar
sources of heat and at least 5 cm away
from electric ovens.
• Do not expose the product to direct sun-
light or keep keep in damp environments.
Attaching the plastic wedges
Use the plastic wedges provided with the
product to maintain sufficient space for air
circulation between the product and the
wall.
• Remove the screws on the product and
mount the screws provided with the
wedges.
• Attach 2 plastic wedges on the ventilation
cover as shown in the figure.
Adjusting the Legs
If the product is not in a balanced position,
you can adjust the balance of the product
by rotating the stands on the front right or
left.

EN / 14
For adjusting the doors vertically, Loosen the fixing bolt at the bottom. Turn
the adjusting bolt towards the position
(clockwise/counter clockwise) of the door.
Tighten the fixing bolt to immobilize the po-
sition.
Fixing Bolt
Fixing Bolt
For adjusting the doors horizontally,
Loosen the fixing bolt at the bottom.
Loosen the fixing bolt at the top. Turn the
adjusting bolt on the side towards the posi-
tion (clockwise/counter clockwise) of the
door. In order to immobilize the position,
tighten the fixing bolt at the top. Tighten the
fixing bolt at the bottom.
Fixing Bolt
Adjusting Nut
Fixing Bolt
Adjusting Bolt
4.1 Electrical Connection
WARNING: Do not use extension
or multi sockets in power connec-
tion.
WARNING: Damaged power cable
must be replaced by Authorized
Service.
• Our firm will not assume responsibility for
any damages due to usage without earth-
ing and power connection in compliance
with national regulations.

EN / 15
• The power cable plug must be easily ac-
cessible after installation.
Hot surface warning!
The side walls of your product are
equipped with cooler pipes to en-
hance the cooling system. High
pressure fluid may flow through
these surfaces, and cause hot sur-
faces on the side walls. This is nor-
mal and it does not require servi-
cing. Be careful when you contact
these areas.
5 Preparation
What to do for energy saving
Read the “Safety Instructions” sec-
tion first.
• This refrigerating appliance is not inten-
ded to be used as a built in appliance.
• Do not keep the refrigerator doors open
for long periods.
• Do not place hot food or beverages into
the refrigerator.
5.1 What To Do For Energy Saving
• Do not overfill the refrigerator; blocking
the internal air flow will reduce cooling
capacity.
• Depending on the product’s features; de-
frosting frozen foods in the cooler com-
partment will ensure both energy saving
and preserve food quality.
• Food shall be stored using the drawers in
the cooler compartment in order to en-
sure energy saving and protect food in
better conditions.
• Make sure the foods are not in contact
with the cooler compartment temperature
sensor shown below.
• Since hot and humid air will not directly
penetrate into your product when the
doors are not opened, your product will
optimize itself in conditions sufficient to
protect your food.Under these circum-
stances, functions and components such
as compressor, fan, heater, defrost, light-
ing, display and so on will operate ac-
cording to the needs by consuming min-
imum energy.
• In case that multiple options are present,
glass shelves must be placed so that the
air outlets at the rear wall are not blocked
and preferably, in a way that air outlets
remain below the glass shelf. This com-
bination may help improving air distribu-
tion and energy efficiency.

EN / 16
5.2 First Use
Before using your refrigerator, make sure
the necessary preparations are made in
line with the instructions in "Safety and En-
vironmental Instructions" and "Installation"
sections.
• Keep the product running without placing
any food inside for 12 hours and do not
open the door, unless absolutely neces-
sary.
A sound will be heard when the
compressor is engaged. It is normal
for the product to make noise even
if the compressor is not running, as
fluid and gas may be compressed
in the cooling system.
It is normal for the front edges of
the refrigerator to be warm. These
areas are designed to warm up in
order to prevent condensation.
For some models, indicator panel
turns off automatically 1 minute
after the door closes. It will be re-
activated when the door is opened
or any button is pressed.
5.3 Climate Class and Definitions
Please refer to the Climate Class on the
rating plate of your device. One of the fol-
lowing information is applicable to your
device according to the Climate Class.
•SN: Long Term Temperate Climate: This
cooling device is designed for use at am-
bient temperatures between 10 °C and
32 °C.
•N: Temperate Climate: This cooling
device is designed for use at ambient
temperatures between 16°C and 32 °C.
•ST: Subtropical Climate: This cooling
device is designed for use at ambient
temperatures between 16°C and 38°C.
•T: Tropical Climate: This cooling device
is designed for use at ambient temperat-
ures between 16°C and 43°C.
6 Operating the Product
Read the “Safety Instructions” sec-
tion first!
• Do not use any mechanical tools or any
other tools than the recommendations of
the manufacturer to speed up the thaw-
ing operation.
• Do not use parts of your refrigerator such
as the door or drawers as a support or a
step. This may cause the product to trip
over or its components to be damaged.
• The product shall be used for storing
food only.
• Turn off the water valve if you will be
away from home (e.g. at vacation) and
you will not be using the Icematic or the
water dispenser for a long period of time.
Otherwise, water leaks may occur.
Unplugging the Product
• If you are not going to use the product for
a long time, unplug the product from the
socket.
• Remove the food to prevent odours,
• Wait for the ice to melt, clean the interior
and let it dry, leave the doors open to
avoid damaging the inner body plastics.

EN / 17
7 Control Panel of the Product
1
2
345
67
8
9
1 *Wireless 2 Quick freezing
3 High temperature/Fault alert 4 Energy saving (Display Off)
5 The Freezer compartment temperat-
ure setting
6 Vacation function
7 Cooler compartment temperature
setting
8 *Key for resetting wireless connec-
tion settings
9 *Deodoriser Module Key
Read the “Safety Instructions” sec-
tion first.
*Optional: Shown functions are optional,
there may be differences of shape and loc-
ation in functions found on your appliance’s
indicator panel.
Auditory and visual functions on the indic-
ator panel will assist you in using the refri-
gerator.
1. *Wireless Key
You can use this key to make a wireless
connection with your product via Home-
Whiz mobile application. If the key is
pressed on for a long time (3 seconds), the
wireless connection symbol on the display/
indicator will blink (at 0.5 second intervals)
slowly. The home network is introduced to
the product firstly in this way. After making
a wireless connection with the product,
wireless connection symbol illuminates
continuously. After completing the initial in-

EN / 18
stallation, you may activate/deactivate it by
pressing on this key. The wireless connec-
tion symbol will flash quickly (at 0.2 second
intervals) until the connection is estab-
lished. When the connection becomes act-
ive, wireless connection symbol flashes
continuously. If the connection cannot be
established for a long period, check your
connection settings and refer to the
“Troubleshooting” section provided in the
user manual. Use HomeWhiz application
for wireless connection. You can find the in-
stallation steps in the application during in-
stallation. You can access the application
by scanning the QR code on the Home-
Whiz label on the appliance. Application is
offered through App Store for IOS devices,
and through Play Store for Android
devices.Visit https://www.homewhiz.com/ ad-
dress for detailed information.
2.Quick Freezing Key
When you press the quick freezing key, the
LED on the key is illuminated and the quick
freezing function will be activated. Freezer
compartment temperature is set to -27
Celsius. Press the key again to cancel the
function. The quick freezing function will be
automatically cancelled after 24 hours. To
freeze a large amount of fresh food, press
the quick freezing key before placing the
food in the freezer compartment.
3. High temperature / fault alert
This indicator will be active when your refri-
gerator cannot perform adequate cooling or
in case of any sensor error. “E” will be dis-
played on the freezer compartment temper-
ature indicator and figures such as 1,2,3...
will be displayed on the cooler compart-
ment temperature indicator. These figures
on the indicator provide information to the
authorized service about the error that has
occurred. Exclamation mark may be dis-
played when you load warm food to the
freezer compartment or keep the door open
for a long period of time. This is not a fault,
this warning is removed when the food is
cooled down or when any key is pressed.
4. Energy Saving (Display Off) Indicator
When the doors are not opened and closed
for an extended period of time, the energy
saving mode is automatically enabled and
the energy saving icon lights up. When you
activate the energy saving function, all
symbols other than the energy saving sym-
bol disappear on the screen. When the en-
ergy saving function is active, if you press
any key or open the door of the product,
the energy saving function of the refriger-
ator is deactivated and the symbols on the
screen returns to normal. Energy saving
function is an active, factory installed func-
tion, it is not possible to deactivate it.
5. The Freezer Compartment Temperat-
ure Setting Key
In order to set freezer compartment tem-
perature, press on this key. When you
press on this key, the freezer compartment
temperature can be set to
-18,-19,-20,-21,-22,-23,-24 Celsius values.
6. Cooler Compartment Off (Vacation)
Function Key
Press on the key for 3 seconds to activate
the vacation function. Vacation mode is ac-
tivated and the LED on the key is illumin-
ated. “- -” will be displayed on the Cooler
Compartment temperature indicator and
the cooler compartment does not actively
perform cooling. When you activate this
function, it is not suitable to store your food
in the cooler compartment. Other compart-
ments will continue to cool according to
their adjusted temperatures. Press the key
for 3 seconds again to cancel this function.
7. Cooler Compartment Temperature
Setting Key
In order to set the cooler compartment tem-
perature, press on this key. When you
press on this key, the cooler compartment
temperature is set to 8,7,6,5,4,3,2 and 1
Celsius values.

EN / 19
8. *Key for Resetting Wireless Connec-
tion Settings+
To reset wireless connection settings,
Quick freezing and Wireless connection
keys should be pressed on
for 3 seconds simultaneously. All user in-
formation recorded previously are removed
on a product where wireless connection
settings are reset/restored to factory de-
faults.
9. *Deodoriser Module Key
Press on this key for 3 seconds to activate/
deactivate the anti-odour feature. When the
deodoriser feature is active, the LED on the
respective key is illuminated. When the fea-
ture is active, the deodoriser module will be
operated periodically.
8 Using The Product
Read the “Safety Instructions” sec-
tion first!
Storing food in the freezer compartment
• You can activate Quick Freezing function
4-6 hours before freezing function and
perform a faster cooling.
• Bring hot meals to the room temperature
before placing them in the freezer com-
partment.
• Foods to be frozen must be divided into
portions according to a size to be con-
sumed, and frozen in separate packages.
• It is recommended to pack the foods be-
fore placing them in the freezer.
• In order to prevent expiration of storage
time, write the freezing date, time and
name of the product on the package ac-
cording to the storage times of different
foods.
• Consume the foods you have defrosted
quickly. Defrosted foods cannot be
frozen again unless they are cooked. It is
not safe to consume the refrozen fresh
foods without cooking after they are de-
frosted.
• As you freeze fresh foods, do not bring
them in contact with already frozen
foods. Otherwise, frozen foods will be de-
frosted.
Storing the foods, which are sold frozen
• Always follow the instructions of the pro-
ducer in relation to the time during which
you are required to store your foods. Do
not excess the time specified in these in-
structions!
• In order to protect the quality of the food,
keep the time interval between purchas-
ing transaction and storing as short as
possible.
• Buy frozen food which are stored at –18
°C or lower temperatures.
• Avoid buying foods whose packages are
covered with ice etc. This means that the
product could be partially defrosted and
refrozen. Temperature impacts the qual-
ity of the food.
• Do not excess the storing time recom-
mended by the food producer. Remove
only the food as much as you need from
the freezer.
• Except the cases where extreme circum-
stances are available in the environment,
if your product (on the recommended set
values table) is set to the specified set
values, the food keep their freshness for
a longer time both in the fresh product
compartment and freezer compartment.
• If fresh food compartment is set to a
lower temperature, fresh fruits and veget-
ables may be partially frozen.

EN / 20
Recommended set values table
Freezer Compart-
ment Setting
Fridge Compart-
ment Setting
Remarks
-18 °C 4 °C This is the default, recommended setting. This setting is recommended if
ambient temperature is below 30 °C.
-20, -22 or -24 °C 4 °C These settings are recommended for ambient temperatures exceeding 30
°C.
Quick Freeze 4 °C Use when you want to freeze your food in a short time. When the process
ends, the product’s settings will return to previous position.
-18 °C or colder 2 °C Use these settings if you believe the cooler compartment is not cold
enough due to ambient temperature or frequently opening the door.
Quick freezing
1. Activate the quick freezing function 24
hours before placing your fresh foods.
2. After 24 hours after pressing the but-
ton, place your food that you want to
freeze in the third or fourth drawers
with higher freezing capacity.
3. The quick freezing function will be
automatically deactivated after 24
hours.
Freezer details
As per the IEC 62552 standards, the
freezer must have the capacity to freeze
4.5 kg of food items at -18 °C or lower tem-
peratures at 25 °C room temperature in 24
hours for each 100 litres of freezer com-
partment volume.
Food products can only be preserved for
extended periods at or below temperature
of -18 °C.
You can keep the foods fresh for months
(in freezer at or below temperatures of -18
°C).
The food products to be frozen must not
contact the already-frozen food inside to
avoid partial defrosting.
Boil the vegetables and filter the water to
extend the frozen storage time. Place the
food in air-tight packages after filtering and
place in the freezer. Bananas, tomatoes,
lettuce, celery, boiled eggs, potatoes and
similar food items should not be frozen. In
case these foods are frozen, only nutritional
values and eating qualities will be negat-
ively affected. A rotting that would threaten
human health is not in question.
Placing the food
Freezer compartment shelves: Different
frozen foods like meat, fish, ice cream, ve-
getables etc.
Cooler compartment shelves: Food items
inside pots, capped plate and capped
cases, eggs (in closed case)
Cooler compartment door shelves: Small
and packaged food or beverages
Crisper: Vegetables and fruits
Fresh food compartment: Delicatessen
(breakfast food, meat products to be con-
sumed in short time)
Storing food in the cooler compartment
• Compartment temperatures rise promin-
ently if compartment door is opened and
closed frequently and kept open for a
long time, this can reduce the life span of
the food and cause the food to spoil.
• In order not to cause odour and taste
changes, the food should be stored in the
closed containers.
• Do not store too much food in your refri-
gerator. To achieve a better and homo-
geneous cooling, place the food separ-
ately in a way that cold air can wander
through them.
• Provide air flow by leaving a space
between the food and internal wall. If you
lean the food against the rear wall, the
food may freeze.
• Bring cooked hot meals to the room tem-
perature before placing them in the refri-
gerator. Then, you can place the tepid
meal in the lower shelves of your refriger-
ator. Do not place the tepid meals close
to the foods which may easily spoil.