Archgard Marquis DVR-38 Owner's manual

MARQUIS 38
DVT-38 & DVR-38
Direct Vent Gas Fireplace
7116 Beatty Dr
Mission, BC V2V 6B4
Canada
For use with Natural Gas or Propane*
Installer: Please leave this manual with the appliance owner for future reference
200-0044
MARCH 2005
*Conversion Kit Required for Propane Use
WARNING: If the information in this manual is not
followed exactly, fire or explosion may result causing
property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use any
phone in your building.
* Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
* If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
This appliance may be installed in an after-market,
permanently located, manufactured home (USA only)
or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified
kit is used.
USERS’ INSTALLATION
OPERATION and
MAINTENANCE MANUAL

Marquis 38 3
CONTENTS
Introduction 4
General Information 5
Appliance Description and Dimensions 6
Framing Dimensions 7
Clearance to Combustibles 8
Possible Fireplace Locations 9
Venting Instructions 10 - 13
Gas Connections 14
Glass Door Instructions 15
Log Placement Instructions 16
Fan and Valve Diagrams 17
Initial Start Up 18 - 19
Maintenance 20
Troubleshooting 21 - 22
Servicing 23 - 26
Replacement Parts List 27
Warranty 28
Warranty Registration 29
Page
Manufactured by Archgard Industries Ltd., British Columbia, Canada.
Patents Pending

Marquis 38 4
INTRODUCTION
Thank you for purchasing the Marquis DV-38 Direct Vent Built-in Gas Fireplace.
The Marquis DV-38 is one of the most advanced gas fireplaces on the market. It is designed
using the latest technology and manufactured to the highest quality.
Some of the many features are:
* Realistic Fire The Marquis DV-38 has a glowing ember bed in front and soft
flowing flames at the back. A realistic split log set complements the
flames.
∗ Solid Construction The Marquis DV-38 is constructed mainly of satin coated and
galvanized steel for long life and durability.
Please read the manual carefully prior to installation and operation of the appliance.
Proper installation, operation and maintenance of the appliance will provide you with
many years of enjoyment.
CAUTION
Due to high temperatures, the appliance should be located out of traffic and away from furniture and
draperies.
Children and adults should be alerted to the hazards of high surface temperature and stay away to avoid
burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance.
Clothing or other flammable material should not be placed on or near the appliance.
Do not operate with cracked or broken glass. Be careful not to strike or slam the glass.
Any safety screen or guard removed for servicing an appliance must be replaced prior to operating.
Installation and Repair should be done by a qualified service person. The appliance should be inspected
before use and at least annually by a professional service person. More frequent cleaning may be
required due to excessive lint from carpeting, bedding materials, et cetera. It is imperative that the
control compartments, burners and circulating air passageways of the appliance are kept clean.

Marquis 38 5
GENERAL INFORMATION
This appliance is listed by Warnock Hersey for use in both the United States and Canada. It is tested and
certified to the following US and Canadian gas appliance standards.
- ANSI Z21.50-1996 / CGA 2.22-M96, Vented Gas Fireplace and Heaters
- CAN/CGA-2.17-M91, Gas-Fired Appliances for Use at High Altitudes.
Please contact Archgard Industries Ltd. if you have any questions regarding the certification of this
appliance.
APPLIANCE CERTIFICATION
INSTALLATION CODES
This appliance must be installed by a qualified gas appliance installer.
The installation must conform with the local codes or, in the absence of local codes, with the
current National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code,
CAN/CGA-B149, in Canada.
Electrical connections and grounding must conform with local code, or current National
Electrical code, ANSI/NFPA No. 70-1987, in the US and in Canada, the current Canadian
Electrical Code, CSA C22.1.
HIGH ALTITUDE INSTALLATION
When installing this appliance beyond 4500 ft. (1372 m) above sea level, the appliance must be
properly de-rated and installed according to local codes. In the absence of local codes, with the
current National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code,
CAN/CGA-B149, in Canada.
Natural Gas (NG) Propane (LP)
Manifold Pressure 3.5 in. w.c. ( 0.9 kPa) 10.0 in. w.c. ( 2.5 kPa)
Min. Supply Pressure for
Purpose of Input Adjustment 4.5 in. w.c. (1.2 kPa) 11.0 in. w.c. (2.8 kPa)
Orifice Size #48 DMS ( 1.93 mm dia.) #56 DMS ( 1.18 mm dia.)
Nominal Input Rating 16,000 BTU/hr (4.6 kW) 16,000 BTU/hr ( 4.6 kW)
Altitude 0 - 4,500 ft. (0 - 1372 m) 0 - 4,500 ft. (0 - 1372 m)
Primary Air Opening ¼ in. (6 mm) ½ in. (13 mm)
SPECIFICATIONS

Marquis 38 6
APPLIANCE DESCRIPTION & DIMENSIONS
GAS VALVE
CONVECTION FAN
SPEED CONTROL
(Optional)
TOP LOUVERS
GLASS DOOR
APPLIANCE DIMENSIONS
FRONT VIEW
38”
23-1/2”
39-3/4”
TOP VIEW SIDE VIEW
FRONT VIEW
3”
* Except for the vent connector locations, the rear vented DV-38 and top vented DVT-38, have the
same physical dimensions.
6”
1/4”
32”
29-3/4”
21-1/4”
31-1/16”
16-1/4”

Marquis 38 7
FRAMING DIMENSIONS
FRAMING DIMENSIONS
38”
16-¼”
38-½”
26-¼”
38”
54”
TERMINATION
FRAMING
11”
10”
38”
*32-¼” 16-¼”
37”
12 ¾”
1
2
3
4
2”
WHEN INSTALLING A SHELF OVER THE TOP OF REAR /
TOP VENT MODEL DV38, THE FOLLOWING APPLIES:
1. Minimum height from floor to center of top vent must be
37” (940mm)
2. Minimum height from top of vent to combustible material is
2” (51mm)
3. Minimum height from floor to combustible materials used for
frame / shelf is 42½” (1080mm)
4. Minimum height from top of unit (not stand-offs) to combustible
material for frame / shelf is 12¾” (324mm)
29¾”
32¼”
42½”
16¼”

Marquis 38 8
CLEARANCE TO COMBUSTIBLES
CLEARANCES TO COMBUSTIBLES
BACK 0” to stand-offs
SIDES 0” to stand-offs
TOP 0” to stand-offs
BOTTOM 0”
ADJACENT SIDE WALL 1” to side of faceplate
MANTLE see diagram
VENT 1” to outside side and bottom surface,
2” to outside top surface.
PRECAUTIONS
• This appliance must be installed by a qualified gas installer and the installation must
conform to the installation codes.
• Provide adequate clearance around air openings of the appliance. Never obstruct front
openings.
• Provide adequate clearances for proper operation and servicing of the appliance.
• This appliance must be properly connected to a venting system.
Combustible mantle allowed in shaded
area. Mantle extension maybe increased
1” (25mm) for each additional 1” (25mm)
increase in clearance height.
Minimum Height From Top Surround: 6”
Minimum Height From Bottom of Appliance: 37”
NOTE: Low profile wooden crowns and mold-
ings above the unit are not
considered as mantles. I.E. 1” or less protrusions
on the upper mantle facing are acceptable
6” (152 mm)

Marquis 38 9
B
C
F
D
E
A
ACross Corner
BFlush with Wall
CFlat on Wall Corner
DFlat on Wall
EIsland
FRoom Divider
15 ft Max.
15 ft Max.
POSSIBLE FIREPLACE LOCATIONS
LOCATING GAS FIREPLACE
This appliance must be installed in any location that is free of plumbing, electrical wiring and heating or
air conditioning ducts. Select a location that is accessible for venting. See PAGE “ALLOWABLE
TERMINATION LOCATIONS”.
*NOTE: Rear vented gas fireplace DV-38 can only be located in positions A, B, C and D.
REFER TO THE VENTING SELECTION OF THIS MANUAL FOR
ALLOWABLE VENTING CONFIGURATIONS

Marquis 38 10
VENTING INSTRUCTIONS
VENTING
The appliance will not function without being connected to a proper venting system.
This appliance may use 4” and 7” gas flex vents with DV-38 listed vent components, or Simpson Duravent
4 x 6-5/8 direct vent systems with Simpson Dura-vent Adaptor (SDA-3). 7” dia. rigid vent may directly
replace 7” dia. flex vent in all applications.
For best venting performance using gas flex vent, here are some general venting rules that we recommend:
1. Use only 4”and 7” diameter 2-ply certified gas flex vent in a co-axial configuration.
2. Maintain a minimum clearance of 1” to the sides and bottom and 2” to the top outside surface of the
vent pipe and combustible material.
3. Observe any local code restrictions, if any, regarding the installation of this type of gas appliance.
4. Observe the venting chart given in this manual.
5. Use a vent spacer between the inside and outside flex vents at every 3 ft intervals.
6. Never slope horizontal running vents downwards.
7. VERY IMPORTANT: Maintain at least an upward slope of 1” for every 1 ft of horizontal run on
the rear vented models.
8. Terminate the vent with a vent termination supplied by Archgard Industries Ltd.
9. Support horizontal running vents every 3 ft to prevent it from sagging.
10.Wall terminal must be installed a minimum of 12” above grade measured from bottom of terminal.
VENT TERMINATION
1. See “ALLOWABLE TERMINATION LOCATIONS” diagram (page 13) to establish a suitable vent
termination location.
2. In heavy snowfall areas make sure vent termination is located where it can not be blocked by snow
from snow removal equipment.
3. Locate vent termination away from plants, bushes or any other object on or near the vent termination
that will interfere or obstruct the air flow around it.
4. DO NOT recess vent termination into walls, sidings or planters.
5. Vent terminations located below 7ft from grade level or anywhere it can be a burn hazard to the
public, such as patios and balconies, must be protected with an Archgard approved termination cage.
6. Always ensure bottom of Vent Terminal is a minimum of 12” above grade.

Marquis 38 11
VENTING INSTRUCTIONS Cont...
• Chart is for one 90° bend, with 1/4” vertical raise minimum per foot of horizontal length.
• For each additional 90° or two 45°, add 1ft of vertical height.
• Maximum two 90º bends, or equivalent.
• Minimum 2 ft straight length between bends.
Maintain a minimum of 1” clearance to combustibles on sides and bottom and 2” from top surface
of the vent.
The gas fireplace is designed and optimized for majority of the installations with short vents. With
taller vents the flame characteristics will change.
NOTE: Maximum vent lengths subject to local codes.
VENTING CHART (FOR TOP VENTED APPLIANCES ONLY)
10 ft
37”
3 ft1 ft 15 ft
HORIZONTAL LENGTH
(from center of flue outlet to base of termination)
VERTICAL HEIGHT
(from bottom of appliance to center of termination)
7 ft
Venting in this area may require a vent restrictor plate #1.
5 ft 7 ft 9 ft 11 ft 13 ft
31”
Heater
Vertical Venting
between 10 and 24 ft
Rooftop Termina-
tion requires a vent
restrictor plate #2.
VERTICAL VENTING (THROUGH THE ROOF) FOR ROOFTOP VENTED APPLIANCES
• Use only Simpson Dura-Vent 4 x 6-5/8” direct vent systems and Simpson Dura-Vent vent-
ing components.
• Maximum vertical height of 24 feet.
• Vertical height of the vent system must have at least 3 ft or more per 900elbow in the vent
system.
• Vertical height of the vent system must also be increased 1 ft for every 2 ft of horizontal
length added to the vent system.
Example: A vertical venting system with a 900elbow, a horizontal offset of 4 ft and another 900
elbow. Vertical vent height of the vent system must be 3ft + 2ft + 3ft = 8 ft or higher to a maxi-
mum of 24 feet.
Maximum Horizon-
tal run for Rear
Vent is 20” from
back of the unit to
termination or 16”
with a 450elbow.

Marquis 38 12
VENTING INSTRUCTIONS Cont...
RESTRICTOR PLACEMENT “FOR ABOVE 7 FOOT VERTICAL RISE
VENTED APPLICATIONS ONLY”
Vertical Venting Between
Seven Feet (7’) and Ten Feet (10’)
must use Restrictor # 1. Vertical
Venting Between Ten Feet (10’)
and Twenty-four Feet (24’) for
Rooftop Terminations must use
Restrictor #2 . See Venting Chart
on page 10.
Simpson Duravent Archgard System
Archgard System
In the Archgard system the restrictors are placed on the exhaust outlet on the appliance.
Simpson Duravent
With Simpson Duravent locate the restrictor in the exhaust section fitting into the formed lip.
Restrictor Placement
WARNING: These restrictors are only to be installed in the vent system if the vent exceeds 7’
in vertical height, *Restrictor Number 1 below is required. Installing them
under any other circumstances may cause hazardous venting conditions
and may result in personal injury, property damage or death.
“NOT FOR USE IN SIDEWALL VENTED APPLICATIONS”
NOTE: Vent restrictors are designed to reduce vertical stack action for above 7 feet, which will reduce the
velocity of incoming combustion air and not adversely affect the standing pilot or the flame of the
appliance.
Restrictor #1
Restrictor #2

Marquis 38 13
VENTING INSTRUCTIONS Cont...
24
Canadian Installations (1) US Installations (2) Canadian Installations (1) US Installations (2) A= Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm) 12 inches (30 cm) J= Clearance to non-mechanical air
supply inlet to building or the combustion air inlet o any other appliance
12 inches (30 cm) 9 inches (23 cm)
B= Clearance to window or door that may be opened 12 inches (30 cm) 12 inches (30 cm) K= Clearance to a mechanical
air supply inlet 6 feet (1.83 m) 3 feet (91 cm) above if
within 10 feet (3 m) hori-
zontally
C= Clearance to permanently closed window * * L= Clearance above paved
sidewalk or paved driveway located on public property
7 feet (2.13 m) + *
D= Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61 cm) from the center line of the terminal
* * M= Clearance under veranda,
porch, deck, or balcony 12 inches (30 cm) ++ *
E= Clearance to unventilated soffit * * F= Clearance to outside corner * * G= Clearance to inside corner * * H= Clearance to each side of center line extended above meter/regulator assembly
3 feet (91 cm) within a
height 15 feet (4.5 m) above
the
meter/regulator assembly
*
L= Clearance to service regulator vent outlet 3 feet (91 cm) *
(1) In accordance with the current CSA B149.1, National Gas and Propane Installation Code (2) In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
(+) A vent shall not terminate directly above a side walk or paved driveway that is located between two single family dwellings and serves both dwellings (++) Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor. (*) For clearances not specified in ANSI Z223.1/NFPA 54 or CSA B149.1, “Clearances shall be in accordance with local installation codes and the requirements of the gas supplier.”
ALLOWABLE TERMINATION LOCATIONS.

Marquis 38 14
GAS CONNECTIONS
Before connecting the appliance to the gas supply line, double check that the appliance you have
purchased is designed for the gas type you are using. The gas type markings are located on the
certification label and also on the appliance’s gas valve.
Provide adequate clearance for proper installation and checking of the gas connections.
Have your gas supplier or a qualified gas fitter run a gas supply line into the gas fireplace. The
line must be properly sized and fitted according to the installation codes. Up stream of the
appliance supply connection, the fitter shall provide an easily accessible manual shut-off valve.
CAUTION: The appliance and its individual shutoff valve must be disconnected from the
gas supply piping system during any pressure testing of that system at test
pressures in excess of 1/2 psig (3.5 kPa). The appliance must be isolated from
the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system at test pressures
equal to or less than 1/2 psig (3.5 kPa). Failure to do so will damage the
appliance’s gas valve. Such damage is not covered by the manufacturer’s
warranty.
Check for proper gas supply pressure by loosening the set screw on the supply pressure tap
(marked IN) on the gas valve with a small flat tip screw driver and placing a test gauge on the
tap.
The minimum permissible gas supply pressure is 4.5 in. w.c. (1.12 kPa) for natural gas and 11.0
in. w.c. (2.74 kPa) for propane. Maximum gas supply pressure should never exceed 14.0 in. w.c.
(3.48 kPa) or 1/2 psi. for both natural gas and propane.
BE SURE TO TIGHTEN THE PRESSURE TAP SET SCREW AFTER CHECKING THE
PRESSURE. CHECK ALL GAS CONNECTIONS FOR GAS LEAKS.
GAS CONNECTIONS
Please follow the venting instructions as strictly as possible to obtain the best
performance from the appliance.

Marquis 38 15
GLASS DOOR INSTRUCTIONS
GLASS DOOR
WARNING: Do not attempt to remove the glass door when the appliance is hot.
Removing the Glass Door
Remove the top and bottom louvers.
There are two latches under the firebox. Undo the latches, swing the bottom of the door away
from the appliance and then lift the door off the top retaining tabs. Carefully place the door in a
safe location where it cannot be scratched or damaged.
Replacing the Glass Door
The reverse procedure of Removing the Glass Door.
Buckle latch
Buckle latch
Top of door hooks
onto fireplace

Marquis 38 16
LOG PLACEMENT INSTRUCTIONS
PLACEMENT OF LOGSET, FIBER COALS & EMBER WOOL
• Place the back log at the back of the burner tray as shown, behind the two tabs on the burner
tray.
• Place the front log on top of the burner as shown. The metal tabs protruding from the bottom
of the log straddle the side of the burner top.
• Place the branches directly on the front and back logs as shown. There are locating holes on
the bottom of the branches to mate with metal pins protruding from the top of the front log.
• A bag of fiber coals and a bag of ember wool is provided with the heater.
• Place the fiber coals on the burner tray, surrounding the burner. DO NOT place fiber coals on
the burner itself.
• Tear ember wool into 1/2” to 3/4” diameter ember pieces and place them on the edges of the
burner so as to hide the transition between the fiber coals and the burner. Keep the embers
from obstructing the burner ports.
Do not add any materials to the burner, other than the type and amount provided by
Archgard.
LEFT BRANCH RIGHT BRANCH
BACK LOG
WARNING : Do not place the logs and branches in any configuration other then the one
shown, a fire, explosion or excessive carbon monoxide (CO) may result,
causing property damage, personal injury or loss of life.
LOG SETUP DETAIL
COALS
EMBERS FRONT LOG

Marquis 38 17
FAN & VALVE WIRING DIAGRAM/INSTRUCTIONS
ELECTRICAL CONNECTIONS (for optional convection fan kit FK 36/38 only)
• Install the fan first. Remove the lower louvers and gently place the bottom front lip of the blower
mounting bracket into the opening. Slide the blower assembly into the bottom of the fireplace.
Rotate the blower into position. Be careful not to damage the fan blades. The fan blades will now
face towards you. Line up the holes on fan bracket to the mounting bracket at the bottom of the
fireplace. Place a screw at each of the three holes and tighten.
• Run 120VAC power line through the left side of the fireplace and into the bottom of the gas
fireplace.
• Be sure to connect a grounding wire to the side of gas fireplace. Use any screw hole on the side
for this purpose.
• Slide the thermal snap switch into the fork like bracket underneath the left side of the firebox.
• Neatly tie down and tuck the wires down at the bottom and to the back of the fireplace.
• CAUTION: Do not allow any wires to touch the bottom of the firebox. Otherwise, the wires will
melt and short-out.
• Screw the speed controller bracket to the bottom left sidewall of the gas fireplace.
VALVE CONNECTIONS
SPEED CONTROL
LINE CONVECTION FAN
GROUND
110F (43ºC) N.O.
THERMAL SNAP SWITCH
NEUTRAL TO
APPLIANCE
120 VAC
WIRING DIAGRAM
OPTIONAL
REMOTE SWITCH
OPTIONAL
THERMOSTAT
SWITCH
TO SPARKER
PILOT
ASSEMBLY
THERMOPILE
SPARK ELECTRODE
THERMOCOUPLE
PILOT
BURNER
300F N.C.
SPILLAGE
SWITCH

Marquis 38 18
INITIAL START UP INSTRUCTIONS
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING : If you do not follow these instructions exactly, a fire or explosion
may result, causing property damage, personal injury or loss of
life.
This appliance has a pilot which must be lit by hand using the sparker located next
to the appliance valve controls. When lighting the pilot, follow the start-up
procedures exactly.
Do not use this appliance if any part has been under water. Immediately call a
qualified service technician to inspect the appliance and to replace any part of the
control system and any gas control which has been under water.
Use only your hand to push in or turn the gas control knob. Never use tools. If the
knob will not push in or turn by hand, do not try to repair it. Call a qualified service
technician. Force or attempted repair may result in a fire or explosion.
BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell
next to the floor, because some gases are heavier than air and will settle on the
floor. IF YOU SMELL GAS, follow the instruction on the front cover of this
manual.
A.
B.
C.
D.
INITIAL OPERATION
• Check that the appliance is properly vented and connected to the gas supply.
• Check that the logs and branches are properly placed.
• Check all external parts, such as grills, door and control cover are properly attached and
fastened.
• Check to ensure the pressure relief door on top of the firebox and behind the upper
louvers is closed and properly sealed on the gasket.
NOTE : When operated for the first few times, the appliance will emit some odors and
fumes. This is due to the evaporation of oils and solvents used in fabricating the
appliance. Close off the room to the rest of the house and open all windows. Keep
the room well ventilated. Operate the appliance continuously on high setting for at
least 4 to 6 hours. This will ‘burn-in’ the appliance and reduce the chance of odors
and fumes reoccurring the next time the appliance is used.

Marquis 38 19
Set the thermostat, if present, to the lowest level. Press slightly and turn the control knob
clockwise 3to the OFF position and wait 5 minutes; thus allowing any gases to escape
which may have accumulated in the combustion chamber.
Note: LP gases do not vent upward. Then follow step 2 and 3 to establish pilot.
INITIAL START UP INSTRUCTIONS Cont..
Press and turn control knob counterclockwise 4to ON position.
Release control knob. If pilot should go out, turn the control knob to OFF position and
repeat steps 1, 2 and 3.
Note: this will allow reset of INTERLOCK for proper lighting of pilot.
Press slightly and turn control knob counterclockwise 4to PILOT position; depress
control knob and light pilot by repeatedly pressing the sparker. Venting of air may take
place at the pilot prior to the flow of fuel gases. Once flame is established, hold knob
depressed for approximately 60 sec.
START-UP PROCEDURE
1.
2.
3.
4.
5.
6.
Turn thermostat to the desired comfort level or turn ON/OFF switch to the ON position.
7.
TEMPORARY SHUT-DOWN PROCEDURE
To turn off the main burner only, set the thermostat to the lowest setting or turn remote
switch to OFF. Press and turn the control knob clockwise 3to PILOT position.
Press and turn the control knob clockwise 3to the OFF position.
COMPLETE SHUT-DOWN PROCEDURE
Control Knob

Marquis 38 20
MAINTENANCE
CAUTION : Only conduct maintenance on a cold appliance.
The exterior painted surfaces, glass and gold trims may be cleaned with a soft, non-abrasive
cloth and water or a suitable, mild, non-abrasive cleaner.
Regularly,
• Clean and remove any lint accumulations or debris from the grills and in any
combustion and convection air passage ways.
• Keep the appliance area free from combustible materials, such as paper, wood,
clothing, gasoline and flammable solids, liquids and vapors.
• Visually check the height and color of the burner and pilot flames.
• Check for unusual noise, odor and operation of the appliance.
• Check the vent terminal for any damage, or obstruction by plants or debris
accumulation.
Once a Year,
• Remove the glass door and clean the inside of the glass with a soft, non-abrasive cloth
and water or a suitable, mild, non-abrasive cleaner.
• Carefully remove the logs and gently brush off any loose carbon deposits. This job is
best done outside the house, wearing a dust mask.The logs are very fragile, take care not
to break them. After cleaning, the logs must be replaced as per the instructions in this
manual.
• When replacing glass door, ensure the gasket is still secure all around the edge of the
glass and it is sealing against the firebox frame. Replace the gasket is worn, damaged or
falling off.
Once a Year have a qualified service technician,
• Completely inspect the appliance and the venting system.
• Clean and remove any lint accumulations or debris in the firebox, on the burners, on
the pilot, at the primary air opening, on the optional convection air blower and in any
combustion and convection air passage ways.
• Check the safety system of the gas valve.
• Check condition of both glass door gasket and top pressure relief door gasket.
Replace if damaged or worn.
WARNING : All parts removed or disturbed must be properly replaced after maintenance.
Service and repair must be conducted by a qualified service person. If these
instructions are not followed, a fire or explosion may result, causing property
damage, personal injury or loss of life
CLEANING THE APPLIANCE