Archgard Sereno 41 User manual
Sereno 41
MODEL: 41-DVTE41LN-2
GAS FIRED DIRECT VENT FIREPLACE
S/N 410200 AND UP
ARCHGARD FIREPLACE PRODUCTS
7116 Beatty Drive
Mission, BC V2V 6B4 Canada 200-3850-01
August 26, 2020
English and French Installation Manuals available through your
local dealer or visit our website at: www.archgard.com
Les manuels d'installation en anglais et en français son
disponibles chez votre détaillant local ou en visitant notre site
web: www.archgard.com
INSTALLER:
LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER:
RETAIN THIS MANUAL FOR FUTURE REFERENCE.
This appliance may be installed in an aftermarket
permanently located, manufactured home (USA only) or
mobile home where not prohibited by local codes.
This appliance is only for use with the type of gas indicated
on the rating plate. This appliance is not convertible for use
with other gases, unless a certied kit is used.
INSTALLATION, OPERATION, AND
MAINTENANCE MANUAL
- Do not store or use gasoline or other ammable vapors or
liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance
• Do not touch any electrical switch; do not use any
phone in your building
• Leave the building immediately
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas suppliers instructions
• If you can not reach your gas supplier, call the re
department
- Installation and service must be performed by a qualied
installer, service agency or the gas supplier.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in
serious injury, death, or property damage.
Gas Fireplace Energy Eciency Rating
70.08%
Based on CSA P.4.1-15
2
TABLE OF CONTENTS
1.0 Introduction 3
2.0 Safety Information 4
3.0 Technical Information 5
5
5
5
5
4.0 Rating Plate 6
5.0 Installation Checklist 7
6.0 Appliance Overview 8
6.1 Appliance Overview 8
6.2 Unpacking 8
6.3 Barrier Screen 9
10
11
12
7.0 Electrical Connections 13
8.0 Fireplace Dimensions 14
9.0 Prepare The Fireplace 15
15
15
10.0 Venting Instructions 17
19
20
21
23
25
11.0 Framing 26
26
27
28
12.0 Clearances to Combustibles 29
12.1 Mantel Clearances 29
12.2 Hearth Clearances 30
31
12.4 Finishing 32
33
13.0 Gas Connections 34
34
35
14.0 Conversion Kit Instructions 36
14.1 Prepare the Fireplace 36
36
37
37
15.0 Firebox Liner Installation 38
38
40
16.0 Log Set Installation 42
43
46
50
17.0 Operation 51
51
17.2 First Fire 51
52
53
54
18.0 Maintenance 61
61
62
62
62
63
18.6 Replacing Batteries 64
18.7 Replacing Fuse 64
65
66
67
68
69
18.13 Replacing the Burner 70
18.14 Replacing the Fan 70
71
18.16 Replacing the Light Bases 72
73
19.0 Frequently Asked Questions 74
20.0 Replacement Parts List 75
Archgard Limited Warranty 76
3
General Information
1.0 Introduction
41-DVTE41LN-2 are:
•
•
•
•
•
•
•
•
Section 17.4
•
Please complete and submit the warranty registration card included in the back of this manual or by visiting us at:
www.archgard.com/warranty-registration
CPI vs IPI:
Continuous Pilot on Demand Ignition (CPI)
Intermittent Pilot Ignition (IPI)
Model Number Denition (41-DVTE41LN-2)
41
DV Direct Vent
T
E
41 Natural Gas Input Rating in BTU
L
NNatural Gas
-2
4
General Information
2.0 Safety Information
Caution
FOR YOUR SAFETY41-DVTE41LN-2
•
•
•
•
•
•
•
Safety
•
•
•
•
•
•
• WARNING:
•
•
clean
•
•
•
• California Proposition 65 Warning:
Section 5.0
Any alteration to the product that causes carbon or soot deposits that results in any damage or requires cleaning is not the
responsibility of the manufacturer.
5
General Information
3.0 Technical Information
3.1 Appliance Certication
Section 4.0.
Commonwealth of Massachusetts
Archgard Industries Ltd
3.2 Installation Codes
We recommend that our gas hearth products be installed and serviced by professionals who are certied in the U.S. by the
National Fireplace Institute® (NFI) as NFI Gas Specialists.
3.3 Specications
Natural Gas (NG) Propane (LP)
Manifold Pressure
Min. Supply Pressure
Max Supply Pressure
Orice Size
Input Rating
P.4 Fireplace Eciency
(FE) 70.08%
P.4 Steady State Eciency 76.15%
Electrical Rating
Gas Control
Altitude
Primary Air Opening
3.4 High Altitude Installation
6
General Information
4.0 Rating Plate
SAMPLE
Figure 4.0.01:
MODEL: 41-DVTE41LN-2 (SIT 885 Proame)
DO NOT REMOVE THIS LABEL
LISTED VENTED GAS FIREPLACE HEATER and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES. Tested to: ANSI
Z21.88-2017 / CSA 2.33-2017, CSA 2.17-2017, CSA P.4.1-15 and CSA C22.2 No.3 - M1998(R.2014). This vented gas replace
heater is not for use with air lters. Certied for use in both CANADA and USA.
VENTED GAS FIREPLACE HEATER-NOT FOR USE WITH SOLID FUEL.
Manufactured as Natural Gas.
NG LPG
Input rating 22,000 - 41,000 BTU/h
(6.45 - 12.02 kWh)
22,000 - 41,000 BTU/h
(6.45 - 12.02 kWh)
Manifold Pressure 1.1 - 3.8 in. W.C.
(0.27 - 0.95 kPa)
2.9 - 11.0 in. W.C.
(0.72 - 2.74 kPa)
Orice size 3.4 mm dia. #48 DMS (1.93 mm dia.)
Minimum supply pressure for purpose of input
adjustment.
5.0 - 14.0 in. W.C.
(1.2 - 3.5 kPa)
12.0 - 14.0 in. W.C.
(2.9 - 3.5 kPa)
Burner Primary Air Setting 1/8” (3.2 mm) Open 1/2” (12.7 mm) Open
Altitude 0 - 4500 ft (0 - 1372 m) 0 - 4500 ft (0 - 1372 m)
Gas Control SIT 885 Proame II Dynamic Start with Continuous POD
Electrical rating 120 VAC, 60 Hz, less than 2 A.
P.4.1 Fireplace Eciency (FE) 70.08%
Replacement fan Part # RF-305-4224 fan / blower assembly must be used
Keep burner and control compartment clean. See
Instructions accompanying the heater.
Optional fuel conversion kit : See Manual
Minimum clearances to Combustibles:
Chase sides, back & top from replace standos: 0” (0 mm).
Interior sidewall from replace opening: 7.25” (184.2 mm).
Mantle: 8” (203.2 mm) mantle at min 21” (533.4 mm) from top of
the replace opening.
Vent pipe: Sides & Bottom: 1” (25.4 mm), Top: 2” (50.8 mm).
Ceiling: 60” (1524 mm) from replace opening.
See Manual for additional dimensions and clearances.
See IHEAT manual for clearances with IHEAT installed.
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1. Electrical connections and grounding must
be in accordance with local codes, if any; if none, follow the current CAN/CSA C22.1 in Canada and ANSI/NFPA 70 in the
US. This appliance is certied for installation in a bedroom or a bed sitting room. This appliance is only for use with the gas
indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where
not prohibited by local codes. See owner’s manual for details. This appliance is not convertible with other gases, unless a
certied kit is used.
WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this appliance. For assistance or additional information consult a
qualied installer, service agency, or the gas supplier. This appliance must be properly connected to a Direct Vent
venting system in accordance with the manufacturer’s installation instructions.
WARNING: Failure to install this appliance per the manufacturer’s instructions or failure to use only parts specically
approved with this appliance may result in property damage or personal injury.
WARNING: Do not operate the appliance until all sections have been assembled and installed in accordance with the
manufacturer’s instructions.
WARNING: Operation of this appliance when not connected to a properly installed and maintained venting system can result
in carbon monoxide (CO) poisoning and possible death.
Only doors certied with the appliance shall be used.
For use only with barrier part # 41-BS. Follow installation instructions.
Made in Canada by:
Archgard Industries Ltd.
7116 Beatty Dr., Mission, B.C.
September 2019 303-6201-01
MANUFACTURE DATE: 2019 2020 2021 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
7
Installation
5.0 Installation Checklist
This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained
within this installation manual.
Customer: Date Installed:
Install Address: Location of Fireplace:
Installer:
IHEAT: (See IHEAT Installation, Operation, and Maintenance Manual) YES IF NO, WHY NOT?
Appliance Install: (Section 9.0) YES IF NO, WHY NOT?
Venting: (Section 10.0) YES IF NO, WHY NOT?
Maintained 1/4 rise for every 1 ft. on horizontal run.
Wiring / Electrical: (Section 7.0) YES IF NO, WHY NOT?
Gas: (Section 13.0) YES IF NO, WHY NOT?
Finishing (Section 12.0): YES IF NO, WHY NOT?
Appliance Setup: YES IF NO, WHY NOT?
Comments:
8
Installation
6.0 Appliance Overview
6.1 Appliance Overview
Section 6.6
Note:
Figure
6.2.01.
Figure 6.1.01:
6.2 Unpacking
Figure 6.2.01.
Section 6.3
Section 6.4
each screw. See Figure 6.2.02.
Figure 6.2.01: Figure 6.2.02:
Warning:
Figure 6.2.03:
9
Installation
6.3 Barrier Screen
41-BS
WARNING
DO NOT INSTALL THE BARRIER SCREEN WITH THE
GLASS DOOR REMOVED.
Removal
Figure 6.3.01: Screen retainer tabs
Figure 6.3.02:
Installation
Figure 6.3.05:
Figure 6.3.06:
Figure 6.3.04: Screen pin
10
Installation
6.4 Glass Door Installation
WARNING:
Figure 6.4.01: Figure 6.4.02:
Step 1:
Step 2:
Step 3:
Step 4:
Figure 6.4.03: Figure 6.4.04:
If Your Glass Breaks
RP-841-0000
Section 6.3
NOTE:
Warning:
11
Installation
6.5 Accessing The Controls
Figure 6.5.01: Figure 6.5.02:
1. Section 6.3
2. Figure 6.5.01.
3.
Figure 6.5.02Figure 6.5.03.
4. Figure 6.5.04.
Figure 6.5.03: Figure 6.5.04:
Note:
12
Installation
6.6 Rating Plate Location
1. Section 6.3
2. Figure 6.5.01.
3.
Figure 6.6.01.
Note:
Figure 6.6.01:
13
Installation
7.0 Electrical Connections
The 41-DVTE41LN-2
CAUTION:
NOTE:
• Section 6.3
• Section 6.4
• Section 6.5
Step 1:
Figure 7.0.01:
Step 2:
Figure 7.0.02:
Step 3: Step 4:
Figure 7.0.03: Figure 7.0.04:
14
Installation
8.0 Fireplace Dimensions
WARNING
Figure 8.0.01:
12.90m
50.4in
91.3m
35.92in
112.14m
44.151in
4.m
33.334in
0.90m
23.9in
2.54m
1.000in
3.95m
29.113in
Front View
Left Side View
1.4m
.5in
9.4m
3.5in
10.05m
42.145in
99.45m
39.153in
.1m
2.99in
5.m
2.310in
3.1m
14.452in
51.4m
20.32in
1.4m
.59in
23.4m
9.3in
53.22m
20.951in
Top View
34.m
13.44in
13.m
5.423in
Right Side View
15
Installation
NOTE
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Section 12
11.
12.
13.
PLACEMENT CLEARANCE REQUIREMENTS
•
•
• Section 12
•
•
•
9.1 Installation Overview
9.0 Prepare The Fireplace
9.2 Nailing Flange Installation
CAUTION
Always install nailing anges regardless of installation variances.
1:50
SIZE
DWG. NO.
A
REV.
SHEET 9 OF 10
WEIGHT:
41-DVT Framing
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\41-DVT Prototype\41-DVT Framing
Trsday, Agst 24, 2017 3:07:49 PM
SCALE
Wall Board Thickness
(Nailing Flange Setting)
Side Nailing Flanges
Figure 9.2.01
Figure 9.2.01:
Flange
O
O
O
O
IMPORTANT
Appliance clearances and framing specications dier if IHEAT is installed.
See the IHEAT manual before planning your installation.
16
Installation
A
DETAIL A
SCALE 1 : 5
Nailing Flange Extension
A
DETAIL A
SCALE 1 : 10
1:50
SIZE
DWG. NO.
A
REV.
SHEET OF 10
WEIGHT:
41-DVT Framing
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\41-DVT Prototype\41-DVT Framing
Trsday, Agst 24, 2017 3:07:49 PM
SCALE
Figure 9.3.01:
A
DETAIL A
SCALE 1 : 5
Attaching The Nailing Flange Extension
Adjusting The Top Nailing Flange
the tek screws again.
Figure 9.3.02:
Figure 9.3.03:
17
Installation
10.0 Venting Instructions
WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result
in carbon monoxide (CO) poisoning and possible death. The appliance must not be connected to a chimney ue serving a
separate solid fuel burning appliance.
WARNING
in the vent run.
IF INSTALLING FLEX PIPE SYSTEMS:
•
•
•
1:50
SIZE
DWG. NO.
A
REV.
SHEET 10 OF 13
WEIGHT:
41-DVT Framing
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
9/6/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\41-DVT Prototype\41-DVT Framing
Wednesday, September 6, 2017 9:53:25 AM
SCALE
See Section 10.3.
Figure 10.0.01:
wall.
Horizontal Venting Specications:
•
•
•
18
Installation
Figure 10.0.02:
Figure 10.0.03: Firestop Framing Figure 10.0.04: Flashing Installation
Typical Venting Conguration
Attic
Flashing
Combination to Rooine
Flex
Venting
Venting
Attic
Flashing
Flex to Rooine
Flex
Venting
Flashing
Rigid to Rooine
Attic
Venting
19
Installation
Horizontal Vent Sections rise 1/4/ft (21mm/m)
10.1 Vent Run Guide
1:50
SIZE
DWG. NO.
A
REV.
SHEET 10 OF 10
WEIGHT:
41-DVT Framing
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\41-DVT Prototype\41-DVT Framing
Trsday, Agst 24, 2017 10:16:52 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:20
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
DVA 4in Pi
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\DVA 4in Pipe
Trsday, Agst 24, 2017 9:05:20 AM
SCALE
1:50
SIZE
DWG. NO.
A
REV.
SHEET 10 OF 10
WEIGHT:
41-DVT Framing
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/24/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\41-DVT Prototype\41-DVT Framing
Trsday, Agst 24, 2017 10:16:52 AM
SCALE
NOT ALLOWED
Restrictor open
Restrictor closed
•
•
•
• See Section 10.5
6 vertical and above, four 90 elbows can be used.
4 - 511.9 vertical, three 90 elbows can be used.
21 3/8 - 23.9 vertical, one 90 elbow can be used.
2 - 311.9 vertical, two 90 elbows can be used.
1:5
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
4DVA-VCH
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
DATE
NAME
/25/2017
PROPRIETARY AND CONFIDENTIAL
U:\R&D\Prototype CADD\Draent Pipe\46DVA-VC
Friday, Agst 25, 2017 :46:07 AM
SCALE
Figure 10.1.01:
20
Installation
Section 10.2
Before installation:
• Disconnect gas and electrical supply to the replace (including backup batteries)
• Section 6.3
• Section 6.4
10.2 Vent Restrictor Installation
Step 1: Step 2:
Figure 10.2.01: Figure 10.2.02:
Step 3:
Figure 10.2.03:
This manual suits for next models
1
Table of contents
Other Archgard Indoor Fireplace manuals
Archgard
Archgard Chantico 36 User manual
Archgard
Archgard OPTIMA 30 User manual
Archgard
Archgard CHALET 1600I Owner's manual
Archgard
Archgard Pele 345-DVTE31LN-1 User manual
Archgard
Archgard Optima 32-1 Owner's manual
Archgard
Archgard 72-DVTE30P-2 User manual
Archgard
Archgard CHALET 1800 User manual
Archgard
Archgard 40-dvi40n Optima 40 - SB User manual
Archgard
Archgard EURO-25 User manual
Archgard
Archgard DV-520NG Owner's manual
Archgard
Archgard EURO 25-1 User manual
Archgard
Archgard Optima 34 User manual
Archgard
Archgard Kojin 50 User manual
Archgard
Archgard Optima 34 34-DVI34N Owner's manual
Archgard
Archgard Euro 65 Owner's manual
Archgard
Archgard 31-DVIM33 Owner's manual
Archgard
Archgard 72-DVTE30P-2-ERG User manual
Archgard
Archgard Optima 3600O Guide
Archgard
Archgard OPTIMA 30 - 1 Owner's manual
Archgard
Archgard 31-DVIM33C-2 User manual
Popular Indoor Fireplace manuals by other brands
Bronpi
Bronpi FLORIDA Instructions of utilization
Empire Comfort Systems
Empire Comfort Systems DV25IN33LN-3 Installation instructions and owner's manual
Style selections
Style selections 0781454 manual
Wickes
Wickes Slimline Installation and user instructions
Regency Fireplace Products
Regency Fireplace Products Grandview G600EC-NG Owners & installation manual
Empire Comfort Systems
Empire Comfort Systems VFP20IN30L10-1 Installation instructions and owner's manual
Desa
Desa Vanguard VVSR18 OWNER'S OPERATION AND INSTALLATION MANUAL
Verine
Verine LPG series Installation, servicing and user instructions
Escea
Escea DN1150 Corner 400 Installation & service instructions
Stoll
Stoll Essential Build-out Kit Installation & user guide
Regency
Regency P121-NG2 Specifications
Mendip Stoves
Mendip Stoves Christon 550 insert Operation and installation manual
Southern Enterprises
Southern Enterprises FA1080759 Assembly
Regency
Regency ULTRAGLOOW G36D-LP Owners & installation manual
FASTER TOOLS
FASTER TOOLS 8998 instruction manual
Stellar Hearth
Stellar Hearth galaxy pier Installation and operating manual
Heat & Glo
Heat & Glo EXCLAIM-36 installation manual
Montigo
Montigo C38-DV Installation & operation manual