AREQUIPMENT E400 User manual
1
USER MANUAL: E400 LS (Lateral Sliding)
MAN AR 63/07/18/0
3
Index
Basic Information
What’s the E400? ………………………………………………………………………………..……….….……………………...4
1.Specifications E400…………………………………………………………………….……….…..…………………………….5
2.Electric Components………………………………………………………………………………………….……….………...6
3.Electric Installation……………………………………………………………………………………………….…………..…..7
Instructions - Loading/Unloading
4.Unloading Operation: (with trolley installed) ……………………………………………………………………..…8
5.Loading Operation (with trolley installed) …………………………………….……………………………….……10
6.Emergency button………………………………………………………………….………………………………………...…11
7.Unloading Operation: (without trolley installed) ………………….………………………………..……………12
8.Loading Operation (without trolley installed) ………………………………………………………..……………13
9.Lateral Sliding (Optional) ……………………………………………………………………………………..……………..14
Safety – Maintenance- Fixation
10.Safety warnings……………………………………………………………………….……………………………….…..…..15
11.Scheduled Maintenance…………………………………………………………………….………………………………16
12. Fixation …………………………………………………………………………………………………………………………...17
4
E400
The E400 is an electric loader for Mondial Stretcher. The main function is the attachment of
the stretcher to the table and it’s usable in different types of vehicles.
The electrical power eases the access to the ambulance cell and enables the user to make less
effort.
Its structure is made of a high resistance alloy and the attachment points are reinforced in
steel. All aluminum profiles were designed to ensure the mechanical resistance and provide a
pleasant visual aspect.
Optional: Android app
5
1. Specifications
•Weight: 105 kg
•Maximum load capacity: 300Kg
•Dimensions: 2220 x 635 x 475 mm
•3 attachment points
•In Stainless Steel
•Electrically powered movement for loading and unloading
•Security system with power cut
•12V DC Power
•Lateral Movement
6
2. Electric components
Picture 8
7
3. Electric installation
Plug the red wire positive (+) and black negative (-) on 12V 80Ah battery. And use
cables with section 16mm2.
8
4. Unloading Operation: (with trolley installed):
Action
Effect
1.1
Pull the red handle for a few
seconds to release the
hooks (6,7).
- It causes the movement of the central module around 5 cm,
assuring that the upper side hooks are loose/released.
- Central led stays green during this movement.
- Central led stays intermittent red during this movement
(intermittent indefinitely).
- Buttons’ light (13,14) turn on and remains on for 10 min, if
there are no further actions.
- After starting point 1.1 the red handle has no more fuction.
1.2
Press once the button no.
14 to activate.
-The central module moves down until position 8, awaiting
new action.
- Central led stays green during this movement.
- Central led stays intermittent red until you find position 8
(intermittent indefinitely).
- Buttons’ light (13,14) turn on and remains on for 10 min, if
there are no further actions.
-If you press button 13 or 14 without starting point 1.1 there is
no movement.
1.3
Press once the button no.
14 to activate
-The central module will remain fixed, awaiting further
confirmation action.
- Central light turns to intermittent green (intermittent
indefinitely).
- Buttons’ light (13,14) turn on and remains on for 10 min, if
there are no further actions.
1.4
Press once the button no.
14 to activate
-The central module moves to the position (11,12) and is
released. It stops for 3 seconds and goes up again until the
center hooks are completely closed (about 5 cm)
-The central light turns off
-Buttons’ light (13,14) turn on and remains on for 10 min, if
there are no further actions.
1.5
Press once the button no.
13 to activate
-After starting point 1.1 the trolley can still climb back up until
(4,5) where it stops.
-After starting point 1.2 the trolley will move until the unloading
is complete.
-After starting point 1.2, if the button 13 or 14 is pressed the
system stops and the central red light is intermittent
(indefinitely).
1.6
Press once the button no.
-After point 1.4, if you press button 14 the center hooks may
9
IMPORTANT: THE OPERATOR MUST ALWAYS ACCOMPANY THE STRETCHER DURRING THE UNLOADING PROCESS
5. Loading Operation (with trolley installed):
Action
Effect
2.1
Install the trolley until the
-There is no effects
14 to activate
open.
1.7
Press once the button no.
13 or 14 to activate
-Before starting point 1.1, if button 13 or 14 is pressed the
central red light will be intermittent.
10
central module fits
2.2
Press once the button no.
13 to activate
- The central module moves up until position 8, awaiting new
action.
- Central led stays green during this movement.
- Central led stays intermittent red until you find position 8
(intermittent indefinitely).
- Buttons’ light (13,14) turn on and remains on for 10 min, if there
are no further actions.
2.3
Press once the button no.
13 to activate
-The central module remains fix, awaiting further confirmation
action.
- Central light turns to intermittent green (intermittent
indefinitely).
- Buttons’ light (13,14) turn on and remains on for 10 min, if there
are no further actions.
2.4
Press once the button no.
13 to activate
-The central module moves to the position (4,5) where the trolley
is fixed. The central light turns off. The buttons’ light (13,14) turn
on and remains on for 10 min, if there are no further actions.
2.5
Press once the button no.
13 to activate
-After starting point 2.2 the trolley will move until the loading is
complete.
2.6
Press once the button no.
13 or 14 to activate
-After starting point 2.2, if the button 13 or 14 is pressed the
system stops and the central red light is intermittent (indefinitely).
IMPORTANT: THE OPERATOR MUST ALWAYS ACCOMPANY THE STRETCHER DURRING THE LOADING PROCESS
11
6. Emergency button:
Action
Effect
3.1
Emergency button
(Press)
- It causes all movements to stop.
- It cuts the signals to the drive controls.
-Central led stays intermittent red.
-It loses the memory of the direction of movement.
-It loses the memory of the direction of movement, requiring a
new command to move the central module
3.2
Emergency button (OFF)
-The central light turns off
-You need to press 13 or 14 to start movement.
12
7. Unloading Operation: (without trolley installed):
IMPORTANT: THE OPERATOR MUST ALWAYS ACCOMPANY THE STRETCHER DURRING THE UNLOADING PROCESS
Action
Effects
4.1
Pull the red handle for a few
seconds to release the
hooks (6,7).
- It causes the movement of the central module around 5 cm,
assuring that the upper side hooks are loose/released.
- Central led stays green during this movement.
- Central led stays intermittent red during this movement
(intermittent indefinitely).
- Buttons’ light (13,14) turn on and remains on for 10 min, if
there are no further actions.
- After starting point 4.1 the red handle has no more fuction.
4.2
Press once the button no.
14 to activate
-The central module moves down to the position
(11,12) and
release the central hooks. It stops for 3 seconds and goes up
again until the center hooks are completely closed (about 5 cm)
.
-Without the trolley installed there is no stop in position 8.
- Central led stays green during this movement.
- Buttons’ light (13,14) turn on and remains on for 10 min, if
there are no further actions.
-If you press button 13 or 14 without starting point 4.1 there is
no movement.
4.3
Press once the button no.
13 to activate
-After starting point 4.1 the trolley can still climb back up until
(4,5) where it stops.
-After starting point 4.2 the trolley will move until the unloading
is complete.
-After starting point 4.2, if the button 13 or 14 is pressed the
system stops and the central red light is intermittent
(indefinitely).
4.4
Press once the button no.
14 to activate
-After point 4.2, if you press button 14 the center hooks may
open.
4.5
Press once the button no.
13 or 14 to activate
-Before starting point 4.1, if button 13 or 14 is pressed the
central red light will be intermittent.
13
~
8. Loading Operation (without trolley installed):
Action
Effects
5.1
Press once the button no. 13
to activate
-The central module moves to the position (4,5) where it stops.
The central light turns off. The buttons’ light (13,14) turn on and
remains on for 10 min, if there are no further actions.
-Without the trolley installed there is no stop in position 8.
5.2
Press once the button no. 13
to activate
-After starting point 5.1 the trolley will move until the loading is
complete.
5.3
Press once the button no. 13
or 14 to activate
-After starting point 5.1, if the button 13 or 14 is pressed the
sy
stem stops and the central red light is intermittent
(indefinitely).
IMPORTANT: THE OPERATOR MUST ALWAYS ACCOMPANY THE STRETCHER DURRING THE LOADING PROCESS
14
9. Lateral Sliding (Optional):
To make it more accessible, we had two buttons, (in red in the image) one in the front
and one in the back.
To initiate the movement just press one of the buttons during the lateral sliding. You
should release the button when the E400 is at the position desired.
There is a Manual system in the event of an anomaly or electrical failure.
In the image, the fixation zones that allow the E400 to move laterally are marked in
blue.
Back Button
Front Button
Manual System
15
10. Safety warnings:
Risk of falling at the same level -
Take special attention to the handling near the
equipment, taking into account the risk of falling inside the vehicle.
Risk of falling at different levels -
Take special attention to the handling near the
equipment, taking into account the risk of falling from the interior of the vehicle to the
exterior.
Risk of shock or collision with mobile objects - Perform regular maintenance actions to
reduce and/or eliminate the risk of shock or collision coming from parts with high wear or
gaps.
Risk of overload or effort to the operator -
Perform regular maintenance actions to
reduce and/or eliminate the risk of shock or collision coming from parts with high wear or
gaps.
Biological risks - Perform regular cleaning actions to reduce the risk of contamination.
16
11. Scheduled Maintenance
The equipment needs regular maintenance to keep correct and smooth operation. Set up and
follow a maintenance schedule. The table represents minimum intervals for maintenance.
When using maintenance products follow the manufactures direction and read the
manufacturers material safety data sheets.
Make sure to perform a visual inspection every 50 uses
Table 1. Minimum intervals for maintenance
Minimum Maintenance Intervals
Each Use
As Needed
3 Months
Disinfecting
X
Cleaning
X
X
Inspecting
X
Lubricating
X
Disinfecting / Cleaning (Each use)
- Use detergent/disinfectant products compatible with aluminum, stainless steel and rubber.
- To clean check carefully on the product the concentration suggested by the manufacturer, to
avoid damaging the material of the equipment.
- Rinse with water in a limited quantity, dry as much as possible and lubricate guides, bars and
sliding parts.
- If we operate in and aggressive environment (for example saline environment), it is
recommended Every Day a cycle of washing/lubrication to protect the exposed parts.
- The manufacturer will not take responsibility for any damage caused by using a cleaning
product that may damage the surface material.
17
12. Fixation
For a correct installation of the product, its fixation must be done according to the diagram
shown below.
Table of contents
