Argent E10SW1001 User manual

Element Wall Hung
INSTALLATION INSTRUCTIONS
Brisbane
Level 3 / 18Wandoo Street
Fortitude Valley QLD 10006
Sydney
80 Abercrombie Street
Chippendale NSW 2008
Melbourne
206-208 Coventry Street
South Melbourne VIC 3205
Perth
Unit 1 / 40 Collingwood Street
Osborne Park WA 6017
Technical Advice
1300 356 717
Fax
1300 656 057
www.argentaust.com.au
ARG-FII-ELW1-0209
STORE THIS
DOCUMENT
INSTALLATION TIPS
CARE + MAINTENANCE
Care must be taken to dry any spillage or leakage of water which may
gain access to furniture. It is recommended that vanities are installed
to avoid splashes from wet areas such as baths, spas and showers.
All wood composite veneers and polyurethane lacquer are water
resistant only. To ensure the quality of nish is maintained, wipe up
all spills with a clean lightly moistened cloth as soon as they occur.
Use only a soft cloth, or a weak solution of non-abrasive detergent.
Do not expose to excessive heat e.g. from hot hair styling equipment
or naked ames.
To restore accidental scratches, burns etc. on two pack polyurethane
parts or acrylic tops, rub gently with car cutting compound, car polish
or household brass/silver cleaner.
To restore accidental scratches, burns etc. on veneer parts, paint with
similar coloured wood restoration pens, let settle for one minute and
wipe off excess with soft cloth.
WARRANTY INFORMATION
The Argent furniture warranty applies to Argent furniture only.
The Argent Warranty is 5 years against manufacturing fault.
Finishes
All nishes are warranted against chipping and aking, excluding
normal wear and tear for ve (5) years from date of purchase. Fading
of colour due to excessive exposure to sunlight is excluded from the
warranty.
Exclusions
This warranty is for normal domestic limited use only and excludes
any defect or injury caused by or resulting from misuse, abuse or
neglect, accidental damage, improper installation or other alterations
or modications which affect the reliability or performance of the unit
that are not attributable to faulty manufacture.
For full Warranty information visit www.argentaust.com.au
Element 10 Single bowl Wall hung/Stone Stone 900 White 30% Gloss
Element 10 Single bowl Floor mtd /Stone Stone 900 White 30% Gloss Z10SF0901
Element 10 Single bowl Wall hung/Stone Stone 1200 White 30% Gloss
Element 10 Single bowl Floor mtd/ Stone Stone 1200 White 30% Gloss Z10SF1201
Element 10 Dbl bowl Wall hung/Stone Stone 1500 White 30% Gloss
E10SW1001
Element 1000 Wall Hung

PRIOR TO INSTALLATION
Argent recommends a qualied trade
person fit your vanity. Ensure your
furniture is installed to relevant building
codes and Australian Standards.
Please note, Argent will not be liable
for the cost of installation or removal
of the furniture and the warranty will be
voided if damage occurred during or
after installation.
Fit wall hung basin at required height
to secure stud or frame, ensure level.
Fit plumbing.
Remove (1) the drawer units and xings
from inside the vanity and set aside
carefully.
Hold vanity over pipes in correct position.
Use (2) scrap blocks of wood to set at
just under correct height.
INSPECT THE FURNITURE TO
ENSURE NO DAMAGE HAS
OCCURRED DURING TRANSIT.
IF DAMAGE HAS OCCURRED,
OR VISIBLE DEFECTS EXIST,
DO NOT PROCEED WITH
INSTALLATION AND ADVISE
ARGENT IMMEDIATELY.
FURNITURE MUST BE FITTED
THROUGH STUDS INTO THE
WALL. USE FIXING BRACKETS
PROVIDED.
IF STUD POSITIONING DOES
NOT ALIGN WITH FIXING
BRACKETS, CABINET MUST
BE ADDITIONALLY SECURED
THROUGH THE BACK BOARD
TO STUDS. IF NO STUDS ARE
FOUND TO SECURE THROUGH,
NOGGINS MAY BE REQUIRED.
MEASURE & MARK
Find (3) in wall studs to secure to. Measure and mark
position for drilling. Fix through a stud where possible.
If no studs are found to secure through, special xings
may be required. Use xings appropriate to your wall
material.
FIT OFF, ADJUST & FINISH
Drill securing screws appropriate to your wall through
furniture back board into stud and wall.
Replace drawer adjust to ensure all square with the
installed vanity.
Put a bead of waterproof mastic compound around the
back edge of the basin and where the basin touches the
wall. Do not over tighten the basin bolts, to avoid
damaging the basin.
C
C
2
Drawer Adjustment
Feel under the drawer for release
catches. Squeeze catches, lift up
and towards you to release the
drawer from the runners.
1
Ensure drawers are adjusted to sit
square as they may have moved
during transportation. Ensure runners
are locked in place. Basin Sealing
IMPORTANT:
INSPECT THE FURNITURE
TO ENSURE NO DAMAGE
HAS OCCURRED DURING
TRANSIT.
IF DAMAGE HAS
OCCURRED, OR VISIBLE
DEFECTS EXIST, DO
NOT PROCEED WITH
INSTALLATION AND ADVISE
ARGENT IMMEDIATELY.
IMPORTANT:
USE ONLY bathroom
grade silicon sealant
Epoxy type glues
MUST NOT BE USED.
Put a bead of waterproof mastic
compound around the back
edge of the basin and where the
basin touches the wall. Do not
tighten the basin bolts to avoid
damaging the basin.