Arris Ruckus SmartZone 300 User manual

Ruckus SmartZone 300
Spare Solid State Drive
Quick Setup Guide for
SmartZone 5.1
This Quick Setup Guide provides basic instructions for
ordering and installing a spare solid state drive (SSD) into
the Ruckus SmartZone 300 (SZ300) controller.
For information on advanced conguration and
management options, see the Getting Started Guide and
other appropriate documents, which are available for
download from the Ruckus Support website:
https://support.ruckuswireless.com/documents.
This Guide in Other Languages
请从以下网站获得该指南的简体中文版 https://
support.ruckuswireless.com.
Vous trouverez la version française de ce guide à
l'adresse suivante https://support.ruckuswireless.com.
このガイドの日本語版は https://
support.ruckuswireless.com でご覧ください。
이 가이드의 한국어 버전은 웹 사이트 (https://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta
guía en https://support.ruckuswireless.com.
Solid State Drive Ordering Information
To order a spare solid state drive (SSD) for the SmartZone
300 controller, contact Ruckus Support.
For information on how to contact Ruckus Support, visit
https://support.ruckuswireless.com/contact-us. When
asked for the part number, provide the information in the
following table.
Part Number Description
902-S351-0000 Kit, Spare (FRU), solid state disk 64KB,
SZ300
Opening the Front Bezel
The front bezel helps prevent accidental access to the
controller's modules. Before you can install a module,
you must open the front bezel.
NOTE: If the controller is mounted in a rack with
adjacent units below the unit where a module needs to
be serviced, Ruckus recommends extracting the
controller from the rack approximately 5cm (2 in.). This
will provide clearance of the bezel when rotated out
towards you.
Follow these steps to open the front bezel.
1. With the controller in front of you, place your ngers
on both sides of the front bezel.
2. Pull the bezel toward you until it opens.
3. Gently lower the bezel to expose the controller's
replaceable modules.
FIGURE 1 Controller with the front bezel open
Installing a Spare SSD
After you have obtained a spare solid state drive (SSD)
and opened the front bezel of the SmartZone 300
controller, you are ready to install the SSD.
ATTENTION: Unlike the two hard disk drives (HDDs) in
the controller, the single SSD is neither redundant nor
hot-swappable.
Follow these steps to install the SSD.
1. On the controller, run the shutdown command from
the CLI.
device# shutdown
2. When the controller has completely powered down,
locate the SSD tray on the front panel. From the top
of the front panel, disk tray 1 is for the SSD, and disk
trays 2 and 3 are for hard disk drives (HDDs) (see the
following gure).
NOTE: Tray 4 is unused.
FIGURE 2 Disk trays on the front panel of the controller
NOTE: If you are replacing a failed disk, check the
LED of each tray. A red or amber LED indicates that
the disk is not operational.
3. Unlock the disk tray by moving the orange disk tray
lock to the left (unlock) position.
4. Press the black/blue tray button to open the tray
handle.
Copyright © 2018 ARRIS Enterprises LLC. All rights reserved. Page 1 of 2
Published November 2018, Part Number 800-71883-001 Rev A

FIGURE 3 An open disk tray
5. Hold the tray handle, and rmly pull it toward you
until the disk tray, along with the SSD, comes out of
the chassis completely. Put the disk tray assembly
aside.
6. Unpack the replacement SSD. The replacement SSD
comes assembled with its own disk tray.
7. Insert the disk tray (with the replacement SSD) into
the disk bay until the drive locks in the connector on
the SAS backplane.
8. Close the handle, and lock the tray by moving the
orange disk tray lock to the right (lock) position.
9. Verify that the new drive's status LED ashes green.
When the drive's status LED shows solid green, you have
completed inserting an SSD in the SmartZone 300
controller.
Closing the Front Bezel
After you complete installing a module, remember to
close the front bezel to prevent access to the modules
and protect them from dust and dirt.
If the controller is mounted in a rack, before completing
the following steps, grab the side handles on the
controller, and push the controller back into the rack.
Secure the controller to the rack using the rack fasteners.
Perform the following steps to close the front bezel.
1. With the controller in front of you, gently lift the bezel
and push it back onto the front panel of the
controller.
2. Gently press the bezel against the front panel until it
clicks into place.
The bezel should now be ush against the front
panel, completely covering it.
© 2018 ARRIS Enterprises LLC. All rights reserved.
ARRIS, the ARRIS logo, Ruckus, Ruckus Wireless, the Ruckus logo, and
the Big Dog design are trademarks of ARRIS International plc and/or
its aliates. All other trademarks are the property of their respective
owners.
Copyright © 2018 ARRIS Enterprises LLC. All rights reserved. Page 2 of 2
Published November 2018, Part Number 800-71883-001 Rev A