Arrow Antenna CR440 User manual

Page 1
911 E. Fox Farm Rd. #2
Cheyenne, WY 82007 ArrowAntennas.com
Simply the Best [phone]
[email protected]
Corner Reflector for 440 MHz
Guarantee
No hassle refund
If you are not completely
satisfied with any
ARROW ANTENNA
Product it can be returned
for a FULL refund less
shipping and handling
within 90 DAYS of
purchase date.
SIMPLY THE BEST
Model
CR440
We don’t invent antennas.
We simply build them better.

Page 2
Model CR440 Parts List
Fig
# Part Number Part Description Qty Req. Price Each
1 CR14801 Center Boom 1” x 12.5” 1 $18.00
2 CR14802 Reflector Boom 1” x 24” 2 $22.00
3 CR14803 Reflector Element ¼” x 16” 25 $6.25
4 146S03 Driven Element ¼” x 13” 1 $6.00
5 CR14805 Assembly Plate (trapezoid shaped 2” x 3” x 3/16” angle) 2 $15.00
6 146S06 4-40 x ¾” Stainless Screw 26 $.50
7 146S07 Gamma Match Assembly (N Connector & 2.25” Cu, 2” Teflon, 3” Al) 1 $9.00
8 146S08 Shorting Bar Assembly 1 $12.00
9 146S09 Plastic End caps for Booms 6 $0.25
n/a ¼-20 x 1.75” Stainless bolts with nuts and lock washers 4 $1.00
n/a U-bolts, lock washers & nuts 2 $5.00
n/a U-channels with holes for u-bolts. 2 $2.00

Page 3
Assembly Instructions
Tools Required: #1 Philips screw driver and 2 @ 7/16” wrenches.
1. Unwrap all parts.
2. Remove strapping tape from ends of reflector booms.
3. Remove one of the black plastic end caps from each reflector boom.
4. Remove elements from within reflector booms.
5. Replace black plastic end caps on reflector booms.
6. Open the #4-40 x ¾” screws. Screw these into the center of each reflector element with your
fingers before inserting the element into the boom. This is to ensure that all the elements are
threaded properly and the screws start easy. Remove screws from elements.
Reflector Booms Assembly
7. Insert a reflector element in a ¼” hole in a reflector boom. Fix the element in place by
inserting a 4-40 x ¾” screw through the small hole in the side of the boom and screwing it into
the element as shown. When screw is snug, turn ¼ turn more only. (See Assembled Reflector
Boom for element layout.
8. Repeat step 7 for all reflector elements in both reflector booms.
Center Boom Assembly
9. Remove the connector from the center boom (4 screws). Turn the connector 90 degrees and
reinstall with the copper rod sticking out through the rubber grommet in the boom.
10. Insert driven element in a ¼” hole in center boom. Fix the element in place by inserting a 4-
40 x ¾” screw through the small hole in the side of the boom and screwing it into the element
as shown. When screw is snug, turn ¼ turn more only.
11. Insert a reflector element in a ¼” hole in the center boom. Fix the element in place by
inserting a 4-40 x ¾” screw through the small hole in the side of the boom and screwing it into
the element as shown. When screw is snug, turn ¼ turn more only.
Gamma Match Assembly
12. Slide gamma match plastic tube over the copper rod and insert the plastic tube through the
rubber grommet at least 1/8”.
13. Slide the aluminum gamma match tube over the plastic tube.
14. Loosen the screw on the shorting bar and slide the shorting bar over the driven element and
aluminum tubes. Position the shorting bar and aluminum tube as shown in the Gamma Match
Setting figure.
Main Assembly
15. Ensure that the reflector booms have the element securing screws on the outside of the boom.
16. Ensure the gamma match stub is up on the center boom.
17. This is easier with some extra hands to help. Slide the assembly plates (top & bottom) over
the all the rear reflector elements simultaneously.
18. Bolt the assembly plates together using ¼-20 x 1 ¾” bolts.

Page 4
Assembled Reflector Boom 4-40 x ¾” Screw
Holding Element
in Boom
Assembled Center Boom
Assembled Top View (Dark holes have bolts. Light holes have elements.)

Page 5
Above photos show how the elements and bracket are assembled.

Page 6
Gamma Match Setting
Red Plastic Cap
Shortin
g
Ba
r
Aluminum Tube
(
3”
)
Copper Wire (2.25”)
Plastic Tube
(
2”
)
2 15/16”
D
rawing NOT to scale.
0.75”

Page 7
CHECKLIST FOR OUR SHIPPING DEPARTMENT
CR440
___N connector
___Connector replacement sign.
___1” x 12.5” Center Boom
___2 @ 1” x 16” Reflector Booms
___26 Element holes
___26 Set screw holes
___Black gromet(s) in boom adjacent to connector hole.
___6 Black end caps.
___26 @ #4 - 40 X 3/4" Element Screws (Stainless)
___4 @ 4-40 x ¼” connector screws (Stainless)
___Gamma Match Assembly
(2" Plastic – 3" Aluminum & 2.25" Copper on N Connector)
___Solid Shorting Bar Assembly (3 piece)
___25 Reflector Elements 1/4" X 16"
___Driven Element 1/4" X 13"
___2 Corner Reflector Mounting Brackets (2” x 3” x 3/16”
trapezoid shaped)
___2 U-bolts with nuts and lock washers
___2 u channel pieces with holes for u-bolts.
___4 bolts, nuts & flat washers ¼-20 x 1.75”