Arrow Sewing Cabinets K9411 User manual

ASSEMBLY INSTRUCTIONS
Assembly video can be found on our website at www.arrowcabinets.com in the Video Section.
Questions? Call 1-800-533-7347 press 1 or Email: [email protected]
ITEM No.:K9411

Incorrect Correct
The arrow direction=front
1
Screw cam bolts all the way in.
Turn clockwise to lock cam with bolt.
A2
x2 F1
x1 O
L
L
Y2
F2
F2
F2
L
Z
Y1
K1,2,3,4
F2
D
G
X
V1
V2
V2
V1
A3
A3
A
A1
L1,2,3,4

2
QTY.ITEM DESCRIPTION
PARTS LIST
Top panel 1A
Bottom 1G
Left Side Panel 1X
Platform 1A2
1Platform CoverA1
Right Side Panel 1Z
Right Partition 1Y2
Center Panel 1D
Shelves 2F1
Shelves 4F2
Right Door 2V2
LIFTER PART LIST
Left Partition 1Y1
Left Door 2V1
Top panel 2A3
Insert Holder 1O
Drawer Front/Back 8L1
Drawer Left Side 4L2
Drawer Right Side 4L3
Large Drawer Front/Back 2K1
Large Drawer Left Side 1K2
Large Drawer Right Side 1K3
Large Drawer Bottom 1K4
L4 4Drawer Bottom
4*14 Screw
Lifter (692mm) 1
1
Lifter Rail (Left)
Lifter Rail (Right) 1
14

6h1 Hinge
d1 8*30 Dowel Pin-42c1 6*35 Cam Bolt-76
Pre-installed parts
c5 Cam
p1 Threaded Dowel Pin-24
c2 (58")Cam Cover-76
3
6*35 Cam Boltc1
ITEM DESCRIPTION
PARTS LIST
QTY.
76
8*30 Dowel pind1 42
Threaded Dowel Pinp1 24
c2 76
(58")Cam Cover
t1 Castor-4
r3 14mm Spanner-1 b2 4*20 Fix Bolt-8h Handle-4
t1 Castor 4
ITEM DESCRIPTION QTY.
14mm Spannerr3 1
b1 8*16 Fix Bolt 20
h Handle 4
b2 Fix Bolt 8
4*14 Screws1 90
g1 Hinge Body-8
Hinge Bodyg1 8
3.5*10 Screws4 8
s1 4*14 Screw-90h1 Hinge-6 m Magnet-4
Magnetm 4
s1 3.5*25 Screw-3
3.5*25 Screws2 3
1
o1 Cable Port
5
t2 Castor
s4 3.5*10 Screw-8
o1 Cable Port-1
a Wrench-1b1 8*16 Fix Bolt-20
t2 Castor-5
pre-installed on part X
1
metal bar support

6. Screw the metal bar support on to Top Panel A using the s2 screws. Place in
pre-drilled holes at front on panel.
4
STEP 1
s1
h1
S2
r3
m
s1
c1
c1
c1
c1
c1
c1
t1
s1
g1
m
s4
b2
h
5. Screw Caster t1 with spanner r3 into panels V1,V2 as illustrated above.
4. Fix hinge bodies g1 to panels V1 and V2 with screws s1 as illustrated above.
3. Fix handles h to panels V1 and V2 with fix bolts b2 as illustrated above.
2. Insert dowel pins d1 to panels X,Z,Y1,Y2,G and D as illustrated above.
1. Insert cams bolts c1 into panels Y1, X, D, A, G and Z as illustrated above.
Preparing panels A,A3, G, D, X, Z, Y1, Y2, V1 and V2
A
x2 A3
D
G
ZV1/V2
Y1
Y2
X

1. Fix Lifter Rail (right) to X panel with s1 screws following predrilled holes as shown
on the illustration above.
1. Fix Lifter Rail (left) to Y2 panel with s1 screws following predrilled holes as shown
on the illustration above.
5
STEP 2
STEP 3
X
Y2
s1
Screw
s1
Screw

a
b1
t2
Panel G assembly.
STEP 5
c1
Panel D,Y1,Y2,X, and Z assembly.
STEP 4
6
1. Fix castors t2 to panels G with screws b1 as illustrated above.
1.Insert cam bolts on panel Y1,Y2,X and Z into cams on panels D and tighten in a
clockwise direction as illustrated above.
D
XY1
Z
G
Y2

1. Fix Lifter to A2 panel with s1 screws following predrilled holes as shown on the
illustration above.
Lifter Panel assembly.
Panel G assembly.
7
STEP 6
STEP 7
c1
1.Insert cam bolts on panel G into cams on panels X,Z,Y1,Y2 and D and tighten in
a clockwise direction as illustrated above.
G
Y2
Z
Y1
D
X
A2
s1
Screw

Rail tabs
Plastic Guides
2.When lifter pushed to first lock position remove a small wooden block that will be
released from lifter.
1.Position lifter onto side rails using plastic guides; by lowering the lifter make sure
the cable is catch onto the rail tabs on both sides. See illustration above.
Mounting the Lifter Assembly.
o1
c1
Panel A assembly.
STEP 9
STEP 8
8
2. Press in Cable port o1 into side panel X firmly by hand until it sits flush.
1. Insert cam bolts on panel A into cams on panels X,Z,Y1,Y2 and D and tighten
in a clockwise direction as illustrated above.
XY1 Z
A
A2 Lifter Rail
Cable

9
STEP 10
STEP 11
Panel O assembly.
p1
1.Press in pegs with flat surface facing upwards at the same level
on panels Z and Y2.
2.Slide shelf E1 with cut in grooves (if available) downwards on top
of p1 pegs.
Moveable shelf assembly.
p1
c1
1.Insert cam bolts on panel Y2 into cams on panels O and tighten in a clockwise
direction as illustrated above.
O
Y2
F1 Y2
Z

STEP 13
c1
Panel K2,K3 ,K4 assembly.
Door panel V1,V2 assembly.
s1
g1
STEP 12
10
1.Attach V1, V2 door assembly using hinge g1 with screws s1 to panels X and Z as
illustrated above.
1.Insert cam bolts on panel K2 and K3 into cams on panels K4 and tighten in a
clockwise direction as illustrated above.
k3
k2 k4
Z
V2
V1
V2
V1
X

Drawers assembly.
c1
Panel L1,L2,L3 and L4 assembly.
c1
Panel K1 assembly.
STEP 15
STEP 14
11
1. Slide bottom panel L4 into L3, L1, L2 slots.
2. Insert cam bolts on panel L1 into cams on panels L2,L3 and L4 and tighten in
a clockwise direction as illustrated above.
1.Insert cam bolts on panel K1 into cams on panels K2,K3 and K4 and tighten in
a clockwise direction as illustrated above.
L3
L4
L
K
L2
L1
L1
k1
k1 k3
k4
k2

STEP 17
p1
1.Press in pegs with flat surface facing upwards at the same level
on panels X and Y1.
2.Slide shelf E2 with cut in grooves (if available) downwards on top
of p1 pegs.
Moveable shelf assembly.
Panels A3 assembly.
1.Fix Hinges h1 with screws s1 into panels A as illustrated above.
s1
h1
p1
STEP 16
12
F2
XY1
A3
A3 A

You have now successfully completed the
assembly on item:
ITEM No.:K9411