Artila RIO-2010PG User manual

RIO-2010PG
FreeRTOS Programmable Remote I/O Module
User Guide
Version 1.0
Copyright © Artila Electronics Co., Ltd. All Rights Reserved.

Table of Contents
1. Introduction................................................................................................................ 1
1.1 Features.............................................................................................................................. 1
1.2 Specification........................................................................................................................ 1
1.3 Packing List......................................................................................................................... 2
1.4 Optional Accessory............................................................................................................. 2
2. Layout......................................................................................................................... 3
3. Pin Assignment and Definition.................................................................................. 4
3.1 Power Connector ................................................................................................................ 4
3.2 LED Status.......................................................................................................................... 4
3.3 Jumper Setting of Relay Output (JP5 ~ JP12).................................................................... 4
3.4 Serial Port Connector.......................................................................................................... 5
4. Install Manager Utility Software ................................................................................ 6
4.1 Broadcast Search................................................................................................................ 6
5. Install Software Toolchain......................................................................................... 8
6. Install Eclipse IDE ...................................................................................................... 9
6.1 Start Your First Porject........................................................................................................ 9

RIO-2010PG User Guide
‧1‧
1. Introduction
RIO-2010PG is a FreeRTOS Programmable Remote I/O Module.
1.1 Features
NXP LPC1768 ARM Cortex-M3 100MHz
512KB on-chip flash, 64KB SRAM
One full modem RS-232 and one isolated RS-485 serial port
One 10/100Mbps Ethernet ports
One serial console port
Support lwIP and BSD socket library
Support tiny Web server
Windows configuration utility included
Tool chain: Sourcery CodeBench Lite (www.mentor.com) or Keil from ARM
1.2 Specification
CPU: NXP LPC1768 Cortex-M3 100MHz
Serial port:
Port1: RS-232 full modem
Port2: RS-485 2500Vrms isolated
Console: RS-232 three wires
Baud rate: 1200 to 921600bps
Flow control: None / Hardware / Xon_Xoff
Data bit: 5 to 8
Stop bit: 1 to 2
Protection: 15KV ESD
Ethernet:
10/100Mbps, RJ45
Protection: 1500V Magnetic isolation
Isolation digital input:
Channel number: 16
Photo isolation (AC in): 2500Vrms
Logical High: 5~24Vdc
Logical Low: 0~1.5Vdc
Input resistance: 1.2KOhms @0.5W
Relay output:
Channel number: 8
Contact rating: 30VDC@1A or 125VAC@0.5A
1-Wire port: Three-pin terminals x 3 (Maxim 1-Wire)
Power: 9~48VDC power jack and terminal block
Dimension: 182 x 118 x 35.82mm (W x H x D)

RIO-2010PG User Guide
‧2‧
Operating Temperature: 0~70°C
Storage Temperature: -20~85°C
1.3 Packing List
RIO-2010PG: Programmable remote I/O module
Software toolchain (download from Artila cloud)
Manager Utility (download from Artila cloud)
1.4 Optional Accessory
CBL-F10M9-20 (91-0P9M9-001): Serial Console Cable (10Pin Header to DB9 male)
DS18B20 (91-6DS18-001): Programmable Resolution 1-wire Digital Thermometer
PWR-12V-1A (31-62100-000): 110~240VAC to 12VDC 1A Power Adaptor

RIO-2010PG User Guide
‧3‧
2. Layout
Ethernet
1-Wire
Relay Output
(NO or NC Jumper)
Isolated Digital Input
Serial Console
RS-232
RS-485
Power In

RIO-2010PG User Guide
‧4‧
1
3
COM DOX
3. Pin Assignment and Definition
3.1 Power Connector
Connecting 9~48VDC power line to the Power in terminal block. If the power is properly supplied, the
Power LED will keep solid green color and a beep will be heard.
3.2 LED Status
The LED provides the RIO-2010PG operation information. The LED status is described as follow:
Power (PWR) LED: Power LED keeps ON if power (+9VDC to +48VDC) is correct.
Ready (RDY) LED: Ready LED keeps ON when RIO-2010 firmware is ready for operation.
Link / Act (LAN) LED: Link and Activity LED will turn ON when the Ethernet cable is connected.
When there is network data traffic, this LED will flash.
LED 1 / 2 / 3: These LEDs are dual color and they indicates the serial data traffic of RS-485,
RS-232 and serial console respectively. The Yellow LED stands for receiving data and Green
LED means transmitting data.
LED DO1 / DO8: These LEDs indicates the DO status. When the coil of relay is energized, the
LED will be ON.
LED DI1 / DI16: These LEDs indicates the DI status. When the input is high, the LED will be ON.
3.3 Jumper Setting of Relay Output (JP5 ~ JP12)
Normal open: when jumper is shorted to 2-3, the terminal (DOX and COM) is
normal open when DO LED is off.
Normal close: when jumper is connect to 1-2, the terminal (DOX and COM) is
normal close when DO LED is off.
Note
JP2 and JP4 are designed for factory usage and should be set to position 2-3.

RIO-2010PG User Guide
‧5‧
Data+
Data-
COM1: RS-485
3.4 Serial Port Connector
RS-485:
Data+ is pull up to isolated 3.3VDC with 10K Ohm resistor.
Data–is pull low to isolated ground.
Termination resistor is not included. User can add a termination resistor to pad at
position R37 for SMD resistor or dual hole for DIP type resistor.
RS-232 and Console Port:
Serial Port and serial console port use 10-pin header. Please use console cable (91-09PM9-001) to
convert it to DB9 male RS-232 interface.
Pin
COM2
COM3
1
DCD
N/C
2
DSR
N/C
3
RXD
RXD
4
RTS
N/C
5
TXD
TXD
6
CTS
N/C
7
DTR
N/C
8
N/C
N/C
9
GND
GND
10
N/C
N/C
13579
246810
COM2: RS-232
COM3: Console

RIO-2010PG User Guide
‧6‧
4. Install Manager Utility Software
RIO-2010PG comes with Manager utility where you can find many useful software utilities. You need
to install Manager Utility first prior to configure the RIO-2010PG. To install the Manager Utility, please
find the ManagerUtilitysetup.exe as shown following:
4.1 Broadcast Search
Once start Manager utility, you can click telescope icon to search the RIO-2010PG in the network.
Click the device to configure its settings.

RIO-2010PG User Guide
‧7‧
Click the upgrade to upload the new firmware user_main.aff.

RIO-2010PG User Guide
‧8‧
5. Install Software Toolchain
The ToolChain, Sourcery CodeBench Lite ARM EABI Release is available at:
http://www.mentor.com/embedded-software/sourcery-tools/sourcery-codebench/editions/lite-edition/.
Configure the environment to add the path of the toolchain. After installing toolchain, a new path will
be added to Windows Environment i.e.
Sourcery_CodeBench_Lite_for_ARM_EABI\bin
Restart the computer to make the new environment effective. After installation, you can test toolchain
as follow:

RIO-2010PG User Guide
‧9‧
6. Install Eclipse IDE
If you are interesting in using IDE to develop your program, the eclipse IDE is available at:
http://www.eclipse.org/downloads/.
And choose C / C++ compiler option.
6.1 Start Your First Porject
Run eclipse and select a workspace: BSDrls\Examples. You can find the path of the example
program on Artila FTP with path: BSDrls\Examples
Choose C/C++ in the Workbench.

RIO-2010PG User Guide
‧10‧
Modify the make file to compile the program as follow:
Use make file to build target.

RIO-2010PG User Guide
‧11‧
Once project is built, you will find the target execution file user_main.aff is generated and available at:
E01_echoServer_netconn_api\build\gcc\output