Moxa Technologies ioLogik E4200 User manual

ioLogik E4200 User’s Manual
Edition 4.2, April 2017
www.moxa.com/product
© 2017 Moxa Inc. All rights reserved.

ioLogik E4200 User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2017 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Amer
icas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
ioLogik Active Ethernet Modular I/O System Overview.............................................................................1-2
Traditional Remote I/O.................................................................................................................1-2
Active Ethernet Modular I/O .........................................................................................................1-2
Product Features ................................................................................................................................1-3
Slice Form Factor, High Density Modular I/O ...................................................................................1-3
Greater Flexibility with Various I/O Module Choices .........................................................................1-3
Expand to a Maximum of 256 Digital Input/Output Points.................................................................1-3
Auto Detection of Installed Modules ...............................................................................................1-3
Event-based Logic with up to 80 Rules and Unicode Active Messaging................................................1-3
Dual Ethernet LAN Support...........................................................................................................1-3
SMS Supported via a GPRS Modem................................................................................................1-3
Built-in Web Console....................................................................................................................1-3
Package Checklist ...............................................................................................................................1-4
Product Descriptions ...........................................................................................................................1-4
Network Adaptors........................................................................................................................1-4
DC Digital Input Modules ..............................................................................................................1-4
AC Digital Input Modules ..............................................................................................................1-4
Digital Output Modules.................................................................................................................1-4
Relay Output Modules ..................................................................................................................1-4
Analog Input Modules ..................................................................................................................1-4
Temperature Input Modules..........................................................................................................1-5
Analog Output Modules ................................................................................................................1-5
System Modules ..........................................................................................................................1-5
Dimensions ........................................................................................................................................1-5
Network Adaptor .........................................................................................................................1-5
I/O Module .................................................................................................................................1-6
Hardware Reference............................................................................................................................1-6
Panel Guide ................................................................................................................................1-6
Hardware Specifications ......................................................................................................................1-7
LED Indicators....................................................................................................................................1-8
LED Indicators for Network Adaptors .............................................................................................1-8
LED Indicators for I/O Modules .....................................................................................................1-8
2. Initial Setup ...................................................................................................................................... 2-1
System Architecture............................................................................................................................2-2
Installing an I/O Module on a DIN Rail...................................................................................................2-3
Removing the I/O Module from the DIN Rail...........................................................................................2-4
Removing the RTB (Removable Terminal Block) from the I/O Module ........................................................2-5
Installing the RTB on the I/O Module.....................................................................................................2-5
Installing the System Power Module......................................................................................................2-5
Installing the Field Power Module..........................................................................................................2-6
Connecting the Power System ..............................................................................................................2-7
Connecting to the Network...................................................................................................................2-7
ioLogik E4200 Active Ethernet Network Adaptor ..............................................................................2-7
Configuring Your Network Architecture...........................................................................................2-8
3. Utilities ............................................................................................................................................. 3-1
Introduction to Modular ioAdmin...........................................................................................................3-2
Features of Modular ioAdmin.........................................................................................................3-2
Getting Started ...........................................................................................................................3-3
Functions on the Menu Bar ...........................................................................................................3-7
Navigation Panel .........................................................................................................................3-8
Server Context Menu ...................................................................................................................3-9
Quick Links............................................................................................................................... 3-10
Main Window (General).............................................................................................................. 3-10
Administrator Functions ............................................................................................................. 3-11
Using TFTP to Import/Export a Configuration........................................................................................ 3-21
Using ioEventLog .............................................................................................................................. 3-22
Installing ioEventLog ................................................................................................................. 3-22
Basic Functions ......................................................................................................................... 3-23
Main Menu................................................................................................................................ 3-23
4. Using the Built-in Web Console ......................................................................................................... 4-1
Overview for the ioLogik E4200 ............................................................................................................4-2
Entering the Web Console ....................................................................................................................4-2
Overview ...........................................................................................................................................4-3
Basic Settings ....................................................................................................................................4-3
Network Settings ................................................................................................................................4-4
Adaptor Settings .........................................................................................................................4-4

Ethernet Configuration .................................................................................................................4-4
Route Table ................................................................................................................................4-5
I/O Module ........................................................................................................................................4-5
System Management...........................................................................................................................4-6
Accessible IP Settings ..................................................................................................................4-6
SNMP Agent ...............................................................................................................................4-7
Network Connection ....................................................................................................................4-7
Firmware Update.........................................................................................................................4-8
Import System Config..................................................................................................................4-8
Export System Config ..................................................................................................................4-8
Change password ...............................................................................................................................4-9
Load Factory Default ...........................................................................................................................4-9
Save/Restart......................................................................................................................................4-9
5. Click&Go Introduction ....................................................................................................................... 5-1
Overview ...........................................................................................................................................5-2
Features ............................................................................................................................................5-3
Click&Go Logic Basics..........................................................................................................................5-3
Working with Rules .............................................................................................................................5-4
Developing Your Logic Rules .........................................................................................................5-5
Define Global Variables........................................................................................................................5-5
Internal Register Settings.............................................................................................................5-5
Timer Settings ............................................................................................................................5-6
SNMP Trap Server .......................................................................................................................5-7
E-Mail Server ..............................................................................................................................5-7
Active Message Settings...............................................................................................................5-8
SMS Phone Number Book .............................................................................................................5-9
IF/THEN/ELSE Statement ....................................................................................................................5-9
IF Conditions ............................................................................................................................ 5-10
THEN/ELSE Actions.................................................................................................................... 5-12
Working with Click&Go Rulesets ......................................................................................................... 5-16
Activating the Ruleset ................................................................................................................ 5-16
Ruleset Management Bar............................................................................................................ 5-16
Ruleset Import/Export ............................................................................................................... 5-16
A. Pinouts and Cable Wiring .................................................................................................................. A-1
Port Pinout Diagrams ..........................................................................................................................A-1
Ethernet Port Pinouts ...................................................................................................................A-1
Serial Port Pinouts .......................................................................................................................A-1
B. Using Modbus/TCP ............................................................................................................................ B-1
System Configuration Map Addresses ....................................................................................................B-2
3xxxx Read only Registers (Support function 4) ..............................................................................B-2
4xxxx Read/Write Registers (support function 3, 6, 16) ...................................................................B-3
I/O Image Map Addressing ..................................................................................................................B-8
Fixed mode (default mode):.................................................................................................................B-9
Dynamic Mode ...................................................................................................................................B-9
Module Configuration Map..................................................................................................................B-10
DO Module Configuration Map ............................................................................................................ B-10
Input Register Map (R)...............................................................................................................B-10
Holding Register Map (R/W) .......................................................................................................B-10
Coil Map (R/W) ......................................................................................................................... B-10
DI Module Configuration Map: ............................................................................................................B-11
Input Register Map(R) ...............................................................................................................B-11
Holding Register Map(R/W) ........................................................................................................B-11
AO Module Configuration Map............................................................................................................. B-11
Input Register Map (R)...............................................................................................................B-11
Holding Register Map (R/W) .......................................................................................................B-11
AI Module Configuration Map.............................................................................................................. B-12
Input Register Map (R)...............................................................................................................B-12
Holding Register Map (R/W) .......................................................................................................B-12
TC Module Configuration Map:............................................................................................................B-12
Input Register Map (R)...............................................................................................................B-12
Holding Register Map (R/W) .......................................................................................................B-12
RTD Module Configuration Map ...........................................................................................................B-13
Input Register Map (R)...............................................................................................................B-13
Holding Register Map (R/W) .......................................................................................................B-13
Internal Registers .............................................................................................................................B-13
Function 8 .......................................................................................................................................B-13
C. CGI Commands.................................................................................................................................. C-1
D. Network Port Numbers...................................................................................................................... D-1
E. SNMP MIB File................................................................................................................................... E-1

RFC1213 MIB-II supported SNMP variables:...........................................................................................E-2
Private MIB File and SNMP Variables .....................................................................................................E-3
F. Factory Default Settings.................................................................................................................... F-1
G. FCC.................................................................................................................................................... G-1
FCC Statement .................................................................................................................................. G-1
FCC Warning!.................................................................................................................................... G-1

1
1. Introduction
The ioLogik Active Ethernet modular I/O family of advanced, slice-type network I/O products with local
intelligence can connect sensors and on/off switches for automation applications over Ethernet and IP-based
networks.
The following topics are covered in this chapter:

ioLogik Active Ethernet Modular I/O System Overview
Traditional Remote I/O
Active Ethernet Modular I/O

Product Features
Slice Form Factor, High Density Modular I/O
Greater Flexibility with Various I/O Module Choices
Expand to a Maximum of 256 Digital Input/Output Points
Auto Detection of Installed Modules
Event-based Logic with up to 80 Rules and Unicode Active Messaging
Dual Ethernet LAN Support
SMS Supported via a GPRS Modem
Built-in Web Console

Package Checklist

Product Descriptions
Network Adaptors
DC Digital Input Modules
AC Digital Input Modules
Digital Output Modules
Relay Output Modules
Analog Input Modules
Temperature Input Modules
Analog Output Modules
System Modules

Dimensions
Network Adaptor
I/O Module

Hardware Reference
Panel Guide

Hardware Specifications

LED Indicators
LED Indicators for Network Adaptors
LED Indicators for I/O Modules

ioLogik E4200 Introduction
1-2
ioLogik Active Ethernet Modular I/O System
Overview
The ioLogik Active Ethernet modular I/O family of slice-type network I/O products can connect sensors and
on/off devices in any combination and can transfer the captured data or device status to a host computer via
an Ethernet or IP-based network.
ioLogik Active Ethernet modular I/O products consist of two main parts: (1) the network adaptor, and (2) I/O
modules. The network adaptor provides system and field power to connected I/O modules. Up to 16 I/O
modules can be connected to one network adaptor.
Network I/O expansion modules; up to 16 slots
Adaptor (up to 256 DIOs or 64 AIOs)
Traditional Remote I/O
Remote Ethernet modular I/O solutions have been on the market for a long time. Traditional solutions are
“passive,” in the sense that I/O devices wait passively to be polled by a host computer. The response time in
this type of setup, however, tends to be on the order of seconds. The “passive” remote modular I/O structure
is inadequate for data acquisition and control systems that require an efficient, real-time I/O solution with a
response time on the order of hundredths of a second.
Active Ethernet Modular I/O
Moxa’s Active Ethernet modular I/O solutions were developed specifically to address the limitations of the
traditional passive approach. With the passive approach, the host computer polls the I/O device over the
network for the status of each I/O device. With the active approach, the Active Ethernet modular I/O product
intelligently sends the host computer status information only when specified events occur. Using push
technology, the ioLogik I/O device greatly reduces the load on the CPU and network resources. Far fewer
network packets are required and in general the packets are smaller in size since I/O information is only sent
when needed, and only information from the specified I/O device is sent.
Moxa’s active I/O messaging system uses TCP or UDP for I/O messaging and supports sending messages to up
to ten host computers simultaneously. In addition to providing intelligent status reporting, Active Ethernet I/O
products are backwards compatible. That is, they support all of the functions and capabilities of traditional
passive remote I/O products.

ioLogik E4200 Introduction
1-3
Product Features
Slice Form Factor, High Density Modular I/O
The ioLogik E4200’s compact design is well-suited for environments with limited space. The amount of space
needed at the installation site is determined by the number of modules used. For example, the I/O system’s
width is only 117 mm if you are using 5 I/O modules, compared to 231 mm for an I/O with an 8 slot backplane
design.
Greater Flexibility with Various I/O Module Choices
The ioLogik E4200 Active Ethernet modular I/O family supports various types of I/O modules, including DC
digital input, AC digital input, digital output, relay output, analog input, and analog output.
Expand to a Maximum of 256 Digital Input/Output Points
The ioLogik Active Ethernet I/O family can support up to 16 modules. In other words, the family can support up
to 256 digital input/output points or 64 analog input/output points.
Auto Detection of Installed Modules
A utility provided by Moxa automatically detects and displays all of the modules that are installed. This feature
allows users to see exactly what is installed.
Event-based Logic with up to 80 Rules and Unicode Active
Messaging
Active Ethernet modular I/O products come pre-installed with 80 rules of event-based logic. All alarm
messages also support Unicode text.
Dual Ethernet LAN Support
For reliability, ioLogik products have two independent Ethernet ports with two MAC addresses and two IP
addresses.
SMS Supported via a GPRS Modem
Alarm messages can be automatically sent through the RS-232 COM port when the I/O is connected to a GPRS
modem, such as Moxa’s OnCell 2111 or OnCell 2151.
Built-in Web Console
The ioLogik E4200 includes a pre-installed web console that allows you to monitor the I/O status via a web
browser.

ioLogik E4200 Introduction
1-4
Package Checklist
Each network adaptor and I/O module is packed securely in a small box.
If you ordered a network adaptor, the package includes:
•ioLogik E42xx Active Ethernet network adaptor
•End module cover
•Quick installation guide (printed)
If you ordered an I/O module, the package includes:
•M-xxxx I/O module ×1
NOTE: Please notify your sales representative if any of the above items are missing or damaged.
Product Descriptions
Detailed specifications for the ioLogik E4200 are available in the software’s product specification help file. Refer
to the help file for more information. Models supported by this manual are:
Network Adaptors
ioLogik E4200 Dual Ethernet LAN, RS-232, Active Ethernet network adaptor
DC Digital Input Modules
M-1800 8 digital inputs, sink, 24 VDC, removable terminal block
M-1801 8 digital inputs, source, 24 VDC, removable terminal block
M-1600 16 digital inputs, sink, 24 VDC, 20-pin header
M-1601 16 digital inputs, source, 24 VDC, 20-pin header
AC Digital Input Modules
M-1450 4 digital inputs, 110 VAC, removable terminal block
M-1451 4 digital inputs, 220 VAC, removable terminal block
Digital Output Modules
M-2800 8 digital outputs, sink, 24 VDC, 0.5 A, removable terminal block
M-2801 8 digital outputs, source, 24 VDC, 0.5 A, removable terminal block
M-2600 16 digital outputs, sink, 24 VDC, 0.3 A, 20-pin header
M-2601 16 digital outputs, sink, 24 VDC, 0.3 A, 20-pin header
Relay Output Modules
M-2250 2 relay outputs, Form A (N.O.), 2 A, removable terminal block (phased out in May 2009)
M2450 4 relay outputs, Form A (N.O.), 2 A, removable terminal block
Analog Input Modules
M-3802 8 analog inputs, 4 to 20 mA, 12-bit, removable terminal block
M-3810 8 analog inputs, 0 to 10 V, 12-bit, removable terminal block

ioLogik E4200 Introduction
1-5
Temperature Input Modules
M-6200 2 analog inputs, RTD, removable terminal block
M-6201 2 analog inputs, thermocouple, removable terminal block
Analog Output Modules
M-4202 2 analog outputs, 4 to 20 mA, 12-bit, removable terminal block (phased out in May 2009)
M-4210 2 analog outputs, 0 to 10 V, 12-bit, removable terminal block (phased out in May 2009)
M-4202 2 analog outputs, 4 to 20 mA, 12-bit, removable terminal block
M-4210 2 analog outputs, 0 to 10 V, 12-bit, removable terminal block
System Modules
M-7001 System expansion power supply, 1.0 A (5 VDC)
M-7002 Field power distributor, 10 A (24/48 VDC, 110/220 VDC)
M-7804 Potential distributor, 8-ch, 0 VDC
M-7805 Potential distributor, 8-ch, 24 VDC
Dimensions
Network Adaptor
Unit: mm; W x H x D: 45 x 99.8 x 70 mm

ioLogik E4200 Introduction
1-6
I/O Module
Unit: mm; W x H x D: 14 x 99.8 x 70 mm
Hardware Reference
Panel Guide
NOTE
The reset button restarts the
system
and resets all settings to factory defaults. Use a pointed object such as a
straightened paper clip to hold in the reset button down for 5 sec. The READY LED will turn red as you
are
holding the reset button down. The factory defaults will be loaded once the READY LED turns green again. You
may then release the reset button.
LED Indicators
Ready: System Status
I/O: Module Detection
Serial: RS-232 Status
Field Power: Power for I/O Points
Reset
Ethernet LAN 0
Ethernet LAN 1
COM (RS
-232)

ioLogik E4200 Introduction
1-7
Hardware Specifications
LAN
Ethernet:
2 x 10/100 Mbps: 2 MACs, 2 IPs, RJ45 connectors
Protection:
1.5 KV magnetic isolation
Protocols:
Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP, HTTP, SNTP, SMTP
Serial Communication
Interface:
1 x RS-232 (9-pin D-Sub, male)
Parameters:
N, 8, 1
Baudrate:
115,200 bps
Power Requirements
Power Input:
24 VDC nominal, 12 to 36 VDC
Power Consumption:
175 mA @ 24 VDC
Current for I/O Modules:
Max. 1.5A @ 5 VDC
Field Power
Rated Voltage:
11 to 28.8 VDC, 24 VDC typical
Current in Field Power Contact:
Max. 10 A
Isolation
System Power to I/O Driver:
Optical isolation, 3k VDC or 2k Vrms
Physical Characteristics
Dimensions:
45 x 99 x 70 mm (1.77 x 3.90 x 2.76 in)
Note: Please see pages 15
-23 for the dimensions diagram.
Weight:
180 g
Mounting:
DIN rail
Environmental Limits
Operating
Temperature: -10 to 60°C (14 to 140°F)
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity:
5 to 95% (non-condensing)
Altitude:
Up to 2000 m
Note: Please contact Moxa if you require products guaranteed to function properly at high
er altitudes.
Standards and Certifications
Safety:
UL 508
EMI:
61000
-3-2; EN 61000-3-3; EN 61000-6-4; FCC Part 15, Subpart B, Class A
EMS:
EN 61000
-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000
-4-5, EN 61000-4-6, EN 61000-4-8,
EN 61000
-6-2, IEC 61000-4-11
Shock:
IEC 60068-2-27
Freefall:
IEC 60068-2-32
Vibration:
IEC 60068-2-6
Green Product:
RoHS, CRoHS, WEEE
Note: Please check Moxa’s website for the most up
-to-date certification status.
MTBF (mean time between failure)
Time:
357,000 hrs
Database:
Telcordia (Bellcore)
Warranty
Warranty Period:
2 years
Details:
See www.moxa.com/warranty

ioLogik E4200 Introduction
1-8
LED Indicators
LED Indicators for Network Adaptors
Group Pins/Description Printed label
Ethernet On the Plug
Ready
Green: The power is on and the system is working normally
Green-Flashing: Click&Go is active
Red-Flashing: System error
Off: No power
Ready
I/O
OFF: The I/O module is not installed
Green: Connecting to the I/O module
Green-Flashing: Data is being transmitted
Red: Safe mode (implies host connection failure)
Red-Flashing: Safe mode (implies I/O module failure)
I/O
Serial
Green: Tx
Yellow: Rx
Red: Data transmission failure
Serial
Field Power Green: Normal input of 11 to 28.8 V
Red: Voltage out of range Field power
LED Indicators for I/O Modules
Each DIO or AIO module is equipped with a Module Status LED indicating operation status.
LED Name LED Color LED Function
Status
Off Was not powered on during initialization
Green
Steady On: System ready
Flashing: I/O module ready for data transmission
Red Steady On: I/O module hardware problem
Flashing: System bus data transmission error

2
2. Initial Setup
In this chapter, we explain how to install the Ethernet network adaptor and I/O modules.
The following topics are covered in this chapter:

System Architecture

Installing an I/O Module on a DIN Rail

Removing the I/O Module from the DIN Rail

Removing the RTB (Removable Terminal Block) from the I/O Module

Installing the RTB on the I/O Module

Installing the System Power Module

Installing the Field Power Module

Connecting the Power System

Connecting to the Network
ioLogik E4200 Active Ethernet Network Adaptor
Configuring Your Network Architecture

ioLogik E4200 Initial Setup
2-2
System Architecture
The ioLogik E4200 modular I/O consists of a network adaptor that supports Ethernet and up to 16 I/O modules.
•The ioLogik E4200 Active Ethernet network adaptor is the brains of the system. It is responsible for
collecting information from each I/O module and deciding what parameters to use to operate the I/O
module. Communication between the network adaptor and I/O modules is achieved by a system
communication bus.
•Modbus addresses for each I/O channel are arranged dynamically by the network adaptor according to the
installed I/O modules.
•The network adaptor requires two sets of 24 VDC power inputs. One is for the internal logic circuit, and the
other is for field I/O circuits.
•The network adaptor provides 5 VDC power to all connected I/O modules. When the total current
consumption of the I/O modules exceeds 1.5 A, you will need to insert an extra power expansion module.
To determine how many power expansion modules are required, refer to the spreadsheet in Program Files
MOXA IO Server HELP.

ioLogik E4200 Initial Setup
2-3
Installing an I/O Module on a DIN Rail
Step1: Align the I/O module side by side with the network adaptor, making sure that the upper and lower rails
are hooked together.
Step 2: Align the I/O module side by side with the network module and then push the I/O module until it
touches the DIN rail. Next, apply more force until the module clips on to the DIN rail.

ioLogik E4200 Initial Setup
2-4
Removing the I/O Module from the DIN Rail
Step1: Use your finger or a screw driver to pull down the tab on the lower part of the module.
Step2: While still holding down the tab, pull out the module.

ioLogik E4200 Initial Setup
2-5
Removing the RTB (Removable Terminal Block)
from the I/O Module
Pull out the plastic belt from the RTB, and then apply more force until the I/O module is pulled away from the
I/O module.
Installing the RTB on the I/O Module
Step1: Hook the bottom end of the RTB to the I/O module.
Step2: Push down the RTB until it fits snugly on the I/O module, and then push in the plastic belt.
Installing the System Power Module
The system power expansion module is designed to provide extra power when additional I/O expansion
modules are connected. Each ioLogik E4200 can provide 1.5 A @ 5 VDC. If you require more power for your
installed I/O modules, you will need to use an M-7001 module. However, please note that the M-7001 can only
provide 1 A @ 5 VDC.

ioLogik E4200 Initial Setup
2-6
ATTENTION
When the total current consumption for connected I/O modules exceed
s 1.5A, an M-7001 power expansion
module is required.
To determine if
an additional power expansion module is needed, open the
Power Consumption Spreadsheet
located here:
Program Files MOXA IO Server HELP. The spreadsheet requires Microsoft Excel to
operate. Once you enter the I/O modul
e quantity, the spreadsheet will compute automatically how many
power expansion modules are required.
When extra power expansion modules are installed, restart the system in the following sequence to ensure a
proper sta
rt-up.
Power Off Sequence
1.
Unplug the network adaptor’s removable terminal block.
2.
Unplug the expansion module’s removable terminal block.
Power Up Sequence
1.
Plug in the power expansion module’s removable terminal block.
2.
Plug in the network adaptor’s removable terminal block.
ATTENTION
The “End Module” should be covered to prevent unexpected damage to exposed data pins.
Installing the Field Power Module
The field power distributor is designed to isolate different field voltages. Most of the field power DIO/AIO
modules for the ioLogik E4200 series are 24 VDC. If you need to connect 110 VAC, 230 VAC digital input or
output modules, you must use the Field Power Distributor to isolate different field powers within a single ioLogik
E4200 system.
If all of the DIO modules are 110 VAC, you will need at least one field power distributor to isolate the field power
from the network adaptor (likewise when using 24 VDC or 230 VAC). For example, before you connect a 110
VDC or 220 VAC AC digital input module to a 24 VDC DI/O module, you will need an M-7002 field power
distributor.
Some types of Potential Distributor modules provide extra wiring points such as shielding ground, 0 V field
power, and 24 V field power. For example, the 8-channel digital input (sink type) module itself does not have
a 24 V wiring point, but you can add a 24 V potential distributor for easy wiring.

ioLogik E4200 Initial Setup
2-7
Connecting the Power System
Two 24 VDC power sources are required to power the ioLogik E4200. One 24 VDC power input is for system
power, and the other 24 VDC power input is for the field I/O. For field installation, system power and field power
are provided by different power supply systems.
System power:
24 VDC nominal, 11 to 28.8 VDC
Power dissipation:
60 mA
@ 24 VDC
Current for I/O module:
1.5 A @ 5 VDC
Field power:
11 to 28.8 VDC
Max. current for field power contact:
DC 10 A max.
I/O Cable Gauge:
AWG14 to AWG28
ATTENTION
Determine the maximum possible current for each power
wire and common wire. Observe all electrical codes
dictating the maximum current allowed for each wire size. If the current exceeds the maximum rating, the
wiring could overheat, causing serious damage to your equipment. For safety reasons, we recommend a
n
average cable size of 22 AWG. However, you may want to use a different cable size depending on the current
load (the maximum wire size for power connectors is 2 mm).
Connecting to the Network
ioLogik E4200 Active Ethernet Network Adaptor
The ioLogik E4200 Active Ethernet network adaptor supports standard 10/100 Mbps Ethernet. For first time
users, we recommend that you link from your host computer to the ioLogik E4200 over a local Ethernet network
to take care of IP and system configuration. Once the installation is done, you may move the entire I/O system
to the field. Note that you can insert any LAN port to make the configuration setting work.
1. Connect the ioLogik E4200 to the host PC with an Ethernet cable. For initial setup of the ioLogik E4200, we
recommend configuring the ioLogik E4200 using a direct connection to a host computer, rather than
remotely over the network.
Note: While configuring the device, only use one connection. To prevent unexpected errors from
occurring, do not use two connections to connect the ioLogik E4200.
2. If you connect to the host PC through LAN 0, configure the host PC’s IP address to 192.168.127.xxx, with
xxx ranging from 001 to 253). If you connect to the host PC through LAN 1, configure the host PC’s IP
address to 192.168.126.xxx, with xxx ranging from 001 to 253).
In Windows, you will need to do this from the Control Panel.
LAN Port Default IP Address Default Netmask Default Gateway
LAN 0 192.168.127.254 255.255.255.0 None
LAN 1 192.168.126.254 255.255.255.0 None