Artos Denby M06860W User manual

www.artos-westover.com
Installation Guide
Denby Towel Warmer M06860W ( hardwired version )

The Denby Towel Rack is intended for towel warming/drying, auxiliary heating or as a
decorative product.
The average heat up time is about thirty minutes, but would depend on
a)the size of the unit and
b)the initial temperature of the unit.
Typically the unit is programmed to be on an hour before expected use and remain on for
an hour afterwards.
The running cost of the towel rack, is usually similar to the running cost of lights in the
same room.
Clean with a soft cloth and use non abrasive cleaners.
Do not connect heater to the network before having read and understood the following
instructions.
Electrical and plumbing connections must be carried out by qualified personnel and the
unit should be securely mounted to the wall in a vertical position and such that it will not
fall into water if the brackets should loosen. Check with local regulations to verify whether
a GFI is required or not. The following pages are to assist in installation.
In case of damages or failures of the rail/connection, the towel rail should be returned to
the manufacturer or their distributor. The warranty from the manufacturer is NOT VALID
in case of improper use or installation. Product designed for use in Canada and USA on-
ly.
See page 4 for detailed installation steps.
USE
INSTALLATION

TECHNICAL SPECIFCATIONS
TECHNICAL SPECIFICATIONS
Rev 01/08
MODEL# M06860
ELECTRIC VERSION Element
specifications 300W, 110V, 48” cord,
UL approved. Hardwire Kit CSA-US
approved. File ref: 229718
HYDRONIC VERSION Heat ouput
1845 BTU. ½” BSPT tappings.
Steel towel warmers should only
be used in a closed water system,
incorporating a rust inhibitor.
CARE & MAINTENANCE A periodic
wash using warm water and a soft
cloth will retain the high quality finish
of your towel warmer for many years
to come. ON NO ACCOUNT should
any household bleaches, detergents,
abrasive polish, steel wool or similar
cleaning agents be used on this
product.
WALL FIXING Towel warmer
brackets must be securely fastened
to either masonry, wall studs or
plywood board in accordance with
the fitting instructions.
PACKAGING Packaged for regular
UPS type shipping.
WARRANTY Frame 5 years –
Heating element 5 years.
NOTE: Towel warmer must be installed so that electrical cord comes out
of the BOTTOM RIGHT of the unit.

INSTALLATION STEPS
1. Check that all the installation pack contents have been received. There should be 3
items as shown below:
2. DISCONNECT POWER SUPPLY. Connect timer to power supply. The timer can be
placed anywhere in the room ( recommended beside the light switches ) . Refer to in-
structions provided with timer for wiring details.
3. Determine location of towel warmer and provide a single gang electrical box 4 ” below
bottom right of towel warmer ( see spec. sheet ) . Note: where possible, attach at least
two of the brackets to a firm wall stud.
4. Attach bracket pieces 1,2,3, and 4 to towel warmer using diagram 1 below as a guide.
Typically the brackets are positioned between the 2nd and 3rd bars from the top and
bottom. To allow maximum hanging space for the towel, position brackets as near to the
edges as possible.
Brackets Hardwire Kit Timer
Diagram 1
#8 Cap
#1 Securing
Bolt
#2 Front Cylinder
Head
Horizontal Bars
#3 Rear Cylinder Head
#4 Inner Rear
Cylinder
#5 Wall Fixing
Screw
#7 Locking Screw
#6 Outer Rear Cylinder

INSTALLATION STEPS
5. Determine location of #6 outer rear cylinder by measuring the brackets attached to towel
warmer. Attach #6 cylinder to wall with hole for #7 locking screw facing down on the bot-
tom brackets and facing up on the top brackets.
6. Feed the wire from the towel warmer through the tube from the hardwire kit, and slide wall
plate onto the tube.
6. Attach upper brackets with locking screw #7, leaving lower brackets free at this time.
7. Connect wire from towel warmer to the wire coming from the timer. Use the instructions
provided with timer as a guide.
8. Push tube up towel warmer cord, over plastic sleeve, until it touches the hexagonal
chrome collar.
9. Push towel warmer onto the bottom brackets and screw mounting plate to the outlet box
using the screws provided.
10.Insert lower locking screws ( #7 ) . Snap on caps #8.
11.Reconnect power supply. Program timer using the instructions provided with the timer.
Towel warmer will take approximately 30 minutes to heat up to full temperature.
12.ENJOY!

ARTOS Towel Warmer Warranty
®
Item №: M06860W-
Serial №:
This warranty covers against defective product for a period of five years. If a heating element is
installed, this is covered for a period of five years.
Under the warranty we will provide replacement components or product at our discretion.
Westover, Inc is not responsible for labor charges connected with removal or installation.
PLEASE REGISTER THIS PRODUCT ONLINE AT WWW.ARTOS-WESTOVER.COM