Artos T-IWALLP User manual

www.artos-westover.com
Installation Guide
Installation GuideInstallation Guide
Installation Guide
Isis Wall Mounted Towel Warmer T
Isis Wall Mounted Towel Warmer TIsis Wall Mounted Towel Warmer T
Isis Wall Mounted Towel Warmer T-
--
-IWALLP ( plug
IWALLP ( plugIWALLP ( plug
IWALLP ( plug-
--
-in version )
in version )in version )
in version )

The Isis Wall Mounted Towel Rack is intended for towel warming/drying, auxiliary heating
or as a decorative product.
The average heat up time is a out thirty minutes, ut would depend on
a ) the size of the unit and
) the initial temperature of the unit.
Typically the unit is programmed to e on an hour efore expected use and remain on for
an hour afterwards.
The running cost of the towel rack, is usually similar to the running cost of lights in the
same room.
Clean with a soft cloth and use non a rasive cleaners.
Do not connect heater to the network before having read and understood the following
Do not connect heater to the network before having read and understood the following Do not connect heater to the network before having read and understood the following
Do not connect heater to the network before having read and understood the following
instructions.
instructions.instructions.
instructions.
Electrical and plum ing connections must e carried out y qualified personnel and the
unit should e securely mounted to the wall in a vertical position and such that it will not
fall into water if the rackets should loosen. Check with local regulations to verify whether
a GFI is required or not. The following pages are to assist in installation.
In case of damages or failures of the rail/connection, the towel rail should e returned to
the manufacturer or their distri utor. The warranty from the manufacturer is NOT VALID
in case of improper use or installation. Product designed for use in Canada and USA on-
ly.
See page 4 for detailed installation steps.
USE
USE USE
USE
INSTALLATI N
INSTALLATI NINSTALLATI N
INSTALLATI N

TECHNICAL SPECIFCATIONS
TECHNICAL SPECIFICATIONS
Rev 01/08
MODEL# T-IWALL
ELECTRIC VERSION Element
specifications 300W, 110V, 48” co d,
UL app oved. Ha dwi e Kit CSA-US
App oved. File ef: 229718
HYDRONIC VERSION Heat ouput
2600 BTU. ½” BSPT tappings.
Steel towel wa me s should only
be used in a closed wate system,
inco po ating a ust inhibito .
CARE & MAINTENANCE A pe iodic
wash using wa m wate and a soft
cloth will etain the high quality finish
of you towel wa me fo many yea s
to come. ON NO ACCOUNT should
any household bleaches, dete gents,
ab asive polish, steel wool o simila
cleaning agents be used on this
p oduct.
WALL FIXING Towel wa me
b ackets must be secu ely fastened
to eithe mason y, wall studs o
plywood boa d in acco dance with
the fitting inst uctions.
PACKAGING Packaged fo egula
UPS type shipping.
WARRANTY F ame 5 yea s –
Heating element 5 yea s.
NOTE: towel war mer MUST be mounted such that ele-
ment cord comes out of bottom right of unit.

INSTALLATION STEPS
1. Check that all the installation pack contents have een received. There should e 3
items as shown elow:
2.
2.2.
2. Determine location of towel warmer near an electrical outlet. The towel warmer cord is
4 ’ long. Note: where possible, locate unit so that at least one of the upper brackets is
Note: where possible, locate unit so that at least one of the upper brackets is Note: where possible, locate unit so that at least one of the upper brackets is
Note: where possible, locate unit so that at least one of the upper brackets is
attached to a firm wall stud.
attached to a firm wall stud.attached to a firm wall stud.
attached to a firm wall stud.
Bracket Installation:
Bracket Installation: Bracket Installation:
Bracket Installation: ( u se diagram 1 elow as a guide )
3. Determine location of wall plates ‘ A ’ y either holding the towel warmer in desired
location or y using the approximate dimensions on page 3. Attach plates using the wood
screws provided.
4. Attach towel warmer to plates using the set screws ‘ B ’ and allen wrench provided.
Installation Pack:
• 16 wood screws
• 4 wall plates
• 12 set screws
• 1 allen wrench
Diagram 1

CARE & MAINTENANCE
For best results, keep the following in mind to retain the high quality finish of your ARTOS towel
warmer:
• Use a soft, dampened sponge or cloth.
• On no account shout you use an abrasive material such as a brush, scouring pad or steel wool to
clean surfaces.
• olish with a soft dry cloth
WARRANTY
This warranty covers against defective products for a period of five years. Under the warranty we will
provide replacement components or products at our discretion. Damage caused by accident, misuse,
abuse, improper installation, improper cleaning or alteration will void the warranty. . Westover, Inc is
not responsible for labor charges, installation or other incidental or consequential costs.
PLEASE REGISTER THIS PRODUCT ONLINE AT WWW.ARTOS-WESTOVER.COM
Item №: T-IWALLP-
Serial №