Asada CSⅡ-50 User manual

Charging scale CSⅡ-50
【Please read this manual before operating】
Instruction manual
IM1501

Cautions
When LCD is blank, it means OVERLOAD (the
measured weight is heavier than the max
capacity). Please immediately remove the
measured objects away from the platter.
Do not keep the weight placed on the platter for a
long period.
Keep the scale away from the environment with
high temperature、high humidity、heavy press、
heavy bump.
Make sure the scale is located in a flat and plane
surface.
Name of each parts
Indicator
Platform

Specification
Name
Charging scale CSⅡ-50
Code
ES737
Battery
9V battery
Battery life
22 hours continuous
Weight
4.8kg
Load capacity
50kg
Measurement
accuracy
±10g
Resolution
10g
Working
pressure
0-60℃
Dimension
Indicator (L x W x H):
140mm x 92mm x 25mm
Platform(L x W x H):
300mm x 300mm x 50mm
Accessory
Charging scale, 9V battery, case,
Instruction manual

Symbols on LCD
Zero Indication ():
The cursor appears on the right-bottom corner of
LCD (above of ZERO printed on the display-overlay),
and indicates the scale is at zero-point.
Net Weight Indication ():
The cursor appears on the bottom edge of LCD
(above of NET printed on the display-overlay), and
indicates the tare weight has been deducted.
Battery Indication :
When LCD shows , it means that the battery is
running in low-voltage status. This is to remind the
user to change the battery. LCD will show
continuously until the battery has been replaced.
Indication of kg or lb Weighing Mode () :
The cursor will be flashed on the bottom edge of
LCD (above of kg or lb printed on the
display-overlay), and indicates the present weighing
mode.
-
-

Operation Instructions
 ON/OFF key :
Turn on or turn off the scale.
 UNIT key :
It can be switchable the unit (kg / lb / oz / pcs)
Operation of counting (pcs)
1. Press 【UNIT】key to select pcs
2. Press 【UNIT】for 2 seconds until it is displayed
the quantity (S ~ 10) then leave your finger.
3. Put the samples quantity on the platter
4. Press【UNIT】key => select samples quantity =>
it has variation once press the quantity value =>
you may select the digital number for 10 、20、
50、100、200.
5. Select the quantity and finish the sample
quantity selection, the LCD display will be
showed the PCS quantity after the weights
stability.

Battery Symbol ( ):
It will be showed the signal when indicated the
battery is running in low-voltage status. This is for
reminding the user to change the battery as soon as
possible.
 TARE/ZERO key :
If the weight is less than 4% then it will be to “0”; if
the weight is greater than the “0”then do the TARE
operation.
 NET/GROSS key :
It can be switchable with net or gross weights on the
normal situation.
Power Requirements
AC: 110V/60Hz ±10% or 220V/50Hz ±10%
(For optional AC/DC Adaptor)
DC: 9V ALKALINE BATTERY
-
-

Calibration Instructions
Please power off the scale before operating the
following procedures.
1. Turn on the scale, while showing “111111”
“222222” “333333” “444444” “555555” ,press and
hold [ZERO] key; do not release your fingers until
LCD is showed the version (6.2.XX).
2. Press [UNIT] key for 2 seconds to enter Calibration
Mode; LCD will be showed SETUP.
3. Press [UNIT] key to show USUAL, then press
again [UNIT] key to choose [USUAL][CAL-] with
cycle selection. Press [NET] key under CAL- to
enter calibration; LCD will be displayed the weight.
4. Input the Weight value …
Press [NET] with moving flash
Press [UNIT] to adjust the digital value
Press [ZERO] after choosing to have confirmation
5. Display the AD value (dec-) after setting up the
weight value, press [ZERO] after the stability to
confirm the AD value for zero.
6. Put the calibration Weight and press [ZERO] …;
the scale can save data to the EEPROM
automatically after stability and restart this scale.

Code No. IM0397 A