Asante AsanteFAST 10/100 User manual

AsantéFAST
™
10/100
Fast Ethernet PCI Adapter
PC Edition
Installation Guide
PCIAsante FrCover Page 1 Wednesday, August 21, 1996 9:22 AM

AsantéFAST
™
10/100
Fast Ethernet PCI Adapter
PC Edition
Installation Guide
Asanté Technologies, Inc.
821 Fox Lane
San Jose, CA 95131
November 1995
Part Number 06-00244-00 Rev. A
Printed in USA
PCIAsante IFCover Page 1 Wednesday, August 21, 1996 9:22 AM

Copyright Notice
Copyright 1995 byAsantéTechnologies,Inc.
All rights reserved.No part of this manual,or any associated artwork,software,product design
or design concept,may be copied,reproduced or stored,in whole or in part,in any form or by
any means mechanical,electronic,optical,photocopying,recording or otherwise,including
translation to another language or format,without the express written consent ofAsanté
Technologies,Inc.
Trademarks
AsantéTechnologies andAsantéFAST are trademarks ofAsantéTechnologies,Inc.
Microsoft,Windows and theWindows Logo are registered trademarks of Microsoft Corporation.
Ethernet is a registered trademark of the Xerox Corporation.
All brand names and products are trademarks or registered trademarks of their respective
holders.
FCC Information
This device complies with part 15 of the FCC Rules.Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received,including interference that may cause undesired operation.
Operation of this equipment in a residential area is likely to cause interference,in which case,
the user,at his own risk and expense will be required to correct the interference.
AsantéWarranty
AsantéTechnologies,Inc.warrants that this product will be free from defects in title,materials
and manufacturing workmanship.If the product is found to be defective,then,as your sole
remedy and as the manufacturer’s only obligation,AsantéTechnologies,Inc.will repair or
replace the product.This warranty is exclusive and is limited to theAsantéFAST 10/100 adapt-
ers.
This warranty shall not apply to products that have been subjected to abuse,misuse,abnormal
electrical or environmental conditions,or any condition other than what can be considered
normal use.
Warranty Disclaimers
AsantéTechnologies,Inc.makes no other warranties,express,implied or otherwise,regarding
AsantéFAST 10/100 adapters,and specifically disclaims any warranty for merchantability or fit-
ness for a particular purpose.
The exclusion of implied warranties is not permitted in some States and the exclusions speci-
fied herein may not apply to you.This warranty provides you with specific legal rights.There
may be other rights that you have which vary from State to State.
Developer tested only,Novell makes no warranty with respect to this product.
Limitation of Liability
The liability ofAsantéTechnologies,Inc.arising from this warranty and sale shall be limited to a
refund of the purchase price.In no event shallAsantéTechnologies,Inc.be liable for costs of
procurement of substitute products or services,or for any lost profits,or for any consequential,
incidental,direct or indirect damages,however caused and on any theory of liability,arising
from this warranty and sale.These limitations shall apply notwithstanding any failure of
essential purpose of any limited remedy.
PCIAsante IFCover Page 2 Wednesday, August 21, 1996 9:22 AM

DRAFT
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
AsantéFAST 10/100Adapter for PCI . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
PCI Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Installing the Asanté PCI Adapter . . . . . . . . . . . . . . . . . . . . . 2-1
Installing theAdapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Connecting theAdapter to the Network . . . . . . . . . . . . . . . . . . . . . . 2-2
Connecting a UTP Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Configuring theAdapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Self-Configuring the Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Computers without the Self-Configuring Feature . . . . . . . . . . . . .2-3
Configuring 10Mbps, 100Mbps, or Full Duplex Operation . . . . .2-3
Testing theAdapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Installing Network Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Network Operating Systems Supported . . . . . . . . . . . . . . . . . . . . . . . 3-1
Installing Network Specific Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Novell NetWare 3.x Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Novell NetWare 4.x Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Microsoft Windows 95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Microsoft Windows for Workgroups . . . . . . . . . . . . . . . . . . . . . .3-5
Microsoft Windows NT Workstation . . . . . . . . . . . . . . . . . . . . . .3-7

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Link Integrity LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Data Traffic LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
100Mbps Operation LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
10Mbps Operation LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Using the Diagnostic Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1

DRAFT
1
Introduction
AsantéFAST 10/100Adapter for PCI
TheAsantéFAST 10/100 adapter for PCI gives you all-in-one compatibility to
10BASE-T and 100BASE-TX Ethernet networks for PCI-based PC computers.
It’s ideal for resource intensive CAD/CAM,client-server database,multimedia,
pre-press,mission-critical,and server applications.
Install theAsantéFAST 10/100 adapter on your existing 10Mbps (10BASE-T)
network to take advantage of the high-performance design and high-speed
PCI bus right from the start.Then,when it’s time to switch to 100Mbps
(100BASE-TX),simply plug the cable into anAsantéFAST 100 hub or other
100BASE-TX compliant hub and your adapter is ready to run at the 100Mbps
speed.The adapter automatically connects at the correct speed.A single
RJ-45 port and drivers support both 10 and 100Mbps operations.
Using NWay™ auto-negotiation,the adapter will sense the hub-speed and
configure the adapter accordingly.For added ease of use,theAsantéFAST
10/100 adapter has 4 LED lights for instant troubleshooting.
TheAsantéFAST 10/100 adapter for PCI features are:
❏
32-bit bus mastering design allows maximum throughput
without loading the host CPU.
❏ Installs easily with plug and play auto-configuration
through the PCI BIOS (system ROM).
❏ Easily visible LEDs indicate 10Mbps operation,100Mbps
operation,Link integrity and Data traffic.
❏ National Semiconductor’s NWay™ auto-negotiation fea-
ture determines 10Mbps operation,100Mbps operation,
or full duplex operation automatically.
❏ Supports full duplex mode for 20 or 200Mbps operation.
❏ 100% compliant with IEEE 802.3 10BASE-T and 802.3u
100BASE-TX Ethernet standards.
❏ Supports major network operating systems.
❏ Jumperless and switchless operation.
❏ Compliant with PCI specifications,version 2.0.
PCIAsante Ch 1 Intro Page 1 Wednesday, August 21, 1996 9:13 AM

Page 1-2
Introduction
Package Contents
Before going any further,please make sure that you have the following items
in this package:
❏ AsantéFAST 10/100 adapter for PCI
❏ Installation Guide (this manual)
❏ Release Notes
❏ Registration Card
❏ One Driver Disk which includes the following software:
❏ Device drivers for popular network operating sys-
tems
❏ Driver dependent supporting files
❏ Diagnostic utility software
❏
Driver installation documents
PCI Local Bus
The PCI (Peripheral Component Interconnect) local bus is a new industry
standard high performance bus designed for high I/O throughput.The 32-bit
PCI bus runs at a maximum of 33MHz,while handling a maximum data
transfer rate of 132 MBytes/second.
One of the advantages of the PCI bus is that it is processor independent.PCI
devices are also self configuring,making them very easy to install and use.
TheAsantéFAST PCI adapter uses 32-bit bus mastering architecture allowing
maximum throughput with low CPU utilization.
➪ Important: The PCI bus slot used must support bus-mas-
tering operations.
PCIAsante Ch 1 Intro Page 2 Wednesday, August 21, 1996 9:13 AM

2
Installing the Asanté PCI Adapter
Installing theAdapter
The following instructions explain how to install theAsanté PCI adapter.
∆ Note:You do not need to set any jumpers or switches on
the adapter.
1
Turn the power off and remove the computer cover.
➪ Important:A network adapter is sensitive to static elec-
tricity and must be handled carefully.If you do not han-
dle the adapter properly you can damage it and/or your
system.
2
Align the adapter’s edge connector with a PCI bus slot.
➪ Important:The PCI bus slot used must support bus mas-
tering operations.
3
Push the adapter down into the slot until the adapter locks into
place as shown below.
4
Replace the computer cover.
PCIAsante Ch 2 Install Page 1 Wednesday, August 21, 1996 9:15 AM

Page 2-2
Installing the Asanté PCI Adapter
Connecting theAdapter to the Network
TheAsantéFAST 10/100 adapter provides a single RJ-45 port for connecting
the adapter to your network.Using NWay™ auto-negotiation,the adapter
will sense the hub's speed and set the adapter to run at either 10Mbps or
100Mbps.See the Configuring 10Mbps, 100Mbps or Full Duplex Operation
section for more details.
➪ Important: Connection to a 100BASE-TX hub for
100Mbps operation requires a Category 5 unshielded
twisted-pair (UTP) cable.The maximum length from the
100BASE-TX hub to the adapter is 100 meters.Connec-
tion to a 10BASE-T hub for 10Mbps operation requires a
Category 3,4,or 5 UTP cable.
Connecting a UTP Cable
To connect your UTP cable to the network using the RJ-45 connector,follow
the instructions below:
1
Plug the RJ45 connector on one end of your UTP cable into the
adapter’s RJ45 port.
2
Plug the other end of your UTP cable into the network hub or
wall socket connected to a network hub.
3
Turn the computer power on.
Configuring theAdapter
Self-Configuring theAdapter
One of the advantages of PCI is that all of its devices are self-configuring.The
Asanté PCI adapter is designed to utilize this feature.
To configure the adapter,plug it into a PCI slot with bus-mastering capabil-
ity.During system initialization at power-up,the PCI BIOS (system ROM)
configuration software automatically selects an unused interrupt line and
I/O addresses for use with the adapter.You do not need to set interrupts,I/O
addresses,jumpers,or switches to configure the adapter.
PCIAsante Ch 2 Install Page 2 Wednesday, August 21, 1996 9:15 AM

Page 2-3
Connecting the Adapter to the Network
Computers without the Self-Configuring Feature
Early versions of PCI BIOS do not support the PCI specification,version 2.0.
To successfully install the adapter in computers without the self-configuring
feature,you may need to modify IRQ jumper settings on the computer’s
motherboard and/or modify the PCI BIOS setup with the setup utility that
came with your computer system.Refer to your computer manuals for infor-
mation on changing the BIOS setup for a PCI bus.
∆ Note:Check with your computer manufacturer to see if
your computer properly supports the PCI Specification,
version 2.0.
∆ Note:It is recommended that you verify the PCI configu-
ration using the PCI BIOS setup utility after installing the
adapter.Check that your PCI configuration do not con-
flict with other bus configuration.
Configuring 10Mbps,100Mbps,or Full Duplex Operation
TheAsantéFAST 10/100 adapter supports National Semiconductor’s NWay™
auto-negotiation feature.NWay auto-negotiation allows the connected
devices to automatically configure to the highest performance mode of oper-
ation.The hierarchy of this mode of operation is listed below:
❏ 100BASE-TX Full Duplex
❏ 100BASE-TX
❏ 10BASE-T Full Duplex
❏ 10BASE-T
This means that after power up initialization,the adapter will automatically
connect at the appropriate speed (10Mbps or 100Mbps) and/or Full Duplex
without user intervention.The Full Duplex operation can only be configured
with a hub or a switch product that supports it.
If you are initially planning to use the adapter to run at 10Mbps speed,when
you are ready to upgrade to 100Mbps (100BASE-TX),it will not be necessary
to modify the configuration or settings.The same driver will run in both
10Mbps or 100Mbps speed.
Another benefit of NWay auto-negotiation is that a connection will not occur
without a common mode of operation between connecting devices.This
preserves network integrity and minimizes network downtime.
PCIAsante Ch 2 Install Page 3 Wednesday, August 21, 1996 9:15 AM

Page 2-4
Installing the Asanté PCI Adapter
Testing theAdapter
Conducting a test is recommended after performing a first time installation
of the adapter.Successful test performance ensures that the adapter is oper-
ating properly.A diagnostic program for testing the adapter is included on
the Driver Disk.This program runs a number of tests and indicates the
results with PASS or FAIL.
Please refer to Chapter 4 for instructions on how to use the diagnostic pro-
gram.
PCIAsante Ch 2 Install Page 4 Wednesday, August 21, 1996 9:15 AM

3
Installing Network Drivers
Network Operating Systems Supported
After installing,configuring and testing theAsanté PCI adapter,you are ready
to install network drivers and work with your network operating system.
Network operating systems that are supported are:
❏ Novell NetWare,MicrosoftWindows forWorkgroups,
MicrosoftWindows 95,MicrosoftWindows NT,Microsoft
LAN Manager,BanyanVINES,NDIS- and ODI-compliant
operating systems,andTCP/IP.
This chapter describes driver installation in the following environments:
❏ Novell NetWare 3.x Client
❏ Novell NetWare 4.x Client
❏
MicrosoftWindows 95
❏ MicrosoftWindows forWorkgroups
❏ MicrosoftWindows NTWorkstation
In general,the adapter will support a network operating system (NOS) that
works with NDIS and ODI drivers.For details about installing your NOS and
its drivers,refer to the INSTALL.DOC files in each specific NOS subdirectory
on the Driver Disk and/or the manuals provided by your NOS.
∆ Note: The same installed driver can be used for 10Mbps
or 100Mbps operation with theAsantéFAST 10/100
adapter.
PCIAsante Ch 3 Drivers Page 1 Wednesday, August 21, 1996 9:19 AM

Page 3-2
Installing Network Drivers
Installing Network Specific Drivers
Novell NetWare 3.x Client
This section explains how to install Novell NetWare version 3.x ODI client
software.
1
Create a directory named NETWARE on your C drive.
To do this,type the following command at the DOS command
line prompt:
MD C:\NETWARE
2
Insert either the NetWareWSGEN disk that came with NetWare
3.x or your master workstation disk into driveA.
3
Copy the following three files to the NETWARE directory on your
C drive.
❏
LSL.COM
❏
IPXODI.COM
❏
NETX.COM
4
Remove the NetWareWSGEN or master workstation disk from
the floppy drive.
5
Insert theAsanté Driver Disk into floppy driveA.
6
Copy the NET.CFG and the ODI driver files to the NETWARE
directory on your C drive.To do this,type:
COPY A:\NETWARE\NW3.X\CLIENT\NET.CFG C:\NETWARE
COPY A:\NETWARE\NW3.X\CLIENT\ASANTPCI.COM C:\NETWARE
7
Check your
CONFIG.SYS
file to make sure that this line
appears:
DEVICE=C:\DOS\SETVER.EXE
If you don’t see it there,type it in,then save the file.
∆ Note:The SETVER.EXE file must be in the C:\DOS
directory.
8
Remove the Driver Disk from the floppy drive.
9
Restart your computer.
PCIAsante Ch 3 Drivers Page 2 Wednesday, August 21, 1996 9:19 AM

Page 3-3
Installing Network Specific Drivers
10
To run NetWare,type the following four commands,in
sequence,at the C:\NETWARE prompt:
LSL
ASANTPCI
IPXODI
NETX
11
Change to the network drive (usually F),and log in to your net-
work.
Novell NetWare 4.x Client
This section explains how to install Novell NetWare version 4.x client soft-
ware.
1
Run the NetWare Client Install program that came with Netware
4.x.Follow the instructions for the first three steps of the Net-
Ware Client Install program as required.
2
At step 4,press Enter to install the driver for your adapter.
3
When prompted,insert theAsanté Driver Disk into the drive and
type the following:
A:\NETWARE\NW4.X\CLIENT
4
Press Enter.
The Network Board window appears.
5
SelectAsanté PCI EthernetAdapter and press Enter.
The Settings for theAsanté PCI NetworkAdapter window
appears.It displays the selected settings for Base I/O Port,Hard-
ware Interrupt,and Media FrameType.You do not need to mod-
ify these settings.
6
Press ESC to continue.
7
At step 5,press Enter to continue with the NetWare installation.
8
When prompted,insert the appropriate NetWare Client Install
disk and press Enter.
9
Press Enter to exit to the DOS prompt.
PCIAsante Ch 3 Drivers Page 3 Wednesday, August 21, 1996 9:19 AM

Page 3-4
Installing Network Drivers
10
Restart the computer to load the network drivers.
11
To log in to the network,type:
F:login
MicrosoftWindows 95
This section explains how to install the driver to use your adapter withWin-
dows 95.The instructions below assume that you have previously installed
Windows 95 software on the computer.
∆ Note: If you are installingWindows 95 for the first time,
the Plug and Play technology ofWindows 95 will auto-
matically detect theAsantéFAST 10/100 adapter installed
in the computer.The Plug and Play technology will also
select and install the generic“PCI Fast Ethernet DECchip
21140 BasedAdapter”driver from theWindows 95 soft-
ware.However,the generic driver will not work with
theAsanté adapter.The procedure to install the appro-
priateAsantéFAST driver is to choose the Custom Setup
option.For detailed instructions,refer to the
INSTALL.DOC file in theWIN95 subdirectory on the
Driver Disk.
1
StartWindows 95.
2
Click Start button.
3
Select Settings and open Control Panel.
4
In the Control Panel,double-click System icon.
5
Select Device Manager.
6
Select“PCI Fast Ethernet DECchip 21140 BasedAdapter”under
Network adapters device type.
∆ Note: After installing the adapter in the computer, the
Plug and Play technology ofWindows 95 will automati-
cally detect the adapter and will select and install the
generic“PCI Fast Ethernet DECchip 21140 Based
Adapter”driver from theWindows 95 software.How-
ever,the generic driver will not work with theAsanté
adapter and it will need to be removed.
PCIAsante Ch 3 Drivers Page 4 Wednesday, August 21, 1996 9:19 AM

Page 3-5
Installing Network Specific Drivers
7
Click Remove button.
8
Click OK button to confirm device removal.
9
Click No button when asked to restart computer.
10
In the Control Panel,double-click Network icon.
11
ClickAdd button.
12
In the Select Network ComponentType window,selectAdapter.
13
ClickAdd button.
14
Click Have Disk button.
The Install from Disk window appears.
15
Insert theAsanté Driver Disk into driveA.
16
In the“Copy manufacturer's files from:”text box,type:
A:\WIN95
17
Click OK button.
18
Select“AsantéFAST 10/100 PCI EthernetAdapter”then click OK.
19
Click OK button in the Network window.
20
Insert theWindows 95 CD in the CD-ROM drive or insert the
requestedWindows 95 diskette in the floppy drive.
21
Type the correct path for the CD (e.g.d:\win95) or for the dis-
kette in the“Copy files from:”text box.
22
Click OK button to begin copying files.
23
Remove the diskette from driveA.
24
Restart the computer and logon the network.
MicrosoftWindows forWorkgroups
This section shows you how to install the drivers to use your adapter with
Windows forWorkgroups.The instructions assume that you have previously
installedWindows forWorkgroups 3.11 software on the computer.
PCIAsante Ch 3 Drivers Page 5 Wednesday, August 21, 1996 9:19 AM

Page 3-6
Installing Network Drivers
1StartWindows forWorkgroups.
2From the Program Manager,double-click the Network group
icon.
3Double-click the Network Setup icon.
The Network Setup window appears.
4Click the Networks...button.
The Networks window appears.
5Click the radio button to Install MicrosoftWindows Network.
6Click the radio button for No additional network.
7Click the OK button or press Enter.
8Click the Drivers...button.
9Click theAddAdapter...button.
TheAdd NetworkAdapter window appears.
10 Select Unlisted or Updated NetworkAdapter from the list.
11 Click the OK button or press Enter.
The Install Driver window appears.
12 Insert theAsanté Driver Disk into driveA.
13 Type the following in the text box:
A:\WFW
(The text A:\ may already be provided for you.)
14 Click the OK button or press Enter.
The Unlisted or Updated NetworkAdapter window appears.
Asanté PCI EthernetAdapter is listed in the window.
15 Click the OK button or press Enter.
The Network Drivers window appears.
16 Click the Close button.
The Network Setup window appears.
17 Click the OK button or press Enter.
PCIAsante Ch 3 Drivers Page 6 Wednesday, August 21, 1996 9:19 AM

Page 3-7
Installing Network Specific Drivers
The MicrosoftWindows Network Names window appears.Your
User Name,Workgroup,and Computer Name may already appear
in the text boxes.
18 If necessary,type your User Name,Workgroup,and Computer
Name.
19 Click the OK button or press Enter.
The Install Driver window appears.
20 When prompted to do so,insert the requested disk from the
Windows forWorkgroups disk set into driveA.
21 Click the OK button or press Enter.
22 When prompted to do so,insert the requested disk from the
Windows forWorkgroups disk set into driveA.
23 Click the OK button or press Enter.
24 When prompted to do so,insert theAsanté Driver Disk into drive
A.
25 Type the following in the text box:
A:\WFW
26 Click the OK button or press Enter.
A message window appears stating that Network Setup has mod-
ified the CONFIG.SYS, AUTOEXEC.BAT,and SYSTEM.INI
files.
27 Click the OK button or press Enter.
TheWindows Setup window appears.
28 Click the button that restarts your computer.
MicrosoftWindows NTWorkstation
This section shows you how to install the driver to use your adapter with
MicrosoftWindows NT.The instructions assume that you have previously
installedWindows NT software on your computer.
PCIAsante Ch 3 Drivers Page 7 Wednesday, August 21, 1996 9:19 AM

Page 3-8
Installing Network Drivers
∆Note: For instructions to install the driver to use the
adapter with MicrosoftWindows NTAdvanced Server,
refer to the INSTALL.DOC file in the specificWindows
NT subdirectory.
1StartWindows NT.
2Double-click the Main group icon.
3Double-click the Control Panel.
4Double-click the Network icon.
The Network Settings window appears.
5Click theAddAdapter button.
TheAdd NetworkAdapter window appears.
6Select the <Other> Required disk from manufacturer option then
click the Continue button.
7At the Insert Disk window type:
A:\WIN_NT31 (if you’re using Windows NT version 3.1) or
A:\WIN_NT35 (if you’re using Windows NT version 3.5)
8Press Enter.
The Select OEM Option window appears withAsantéFAST
10/100Adapter as option.
9Select the PCI adapter.
10 Click the OK button.
TheAsantéFAST 10/100Adapter Setup window appears with
ConnectionType highlighted.
11 Select the appropriate ConnectionType from the dropdown list
box.
12 Click the OK button.
The files are copied to the hard drive and then the Network Set-
tings window reappears.
13 Click the OK button to complete the installation.
14 Restart the computer.
PCIAsante Ch 3 Drivers Page 8 Wednesday, August 21, 1996 9:19 AM

4
Troubleshooting
LED Indicators
Overview
The figure below shows the LED indicators that illustrate the presence of
Link Integrity (LI),DataTraffic (TX),100Mbps operation and 10Mbps opera-
tion for installation verification and diagnostic purposes.
10Mbps LED100Mbps LED TX LEDLI LED
AsantéFAST 10/100 adapter