ASG PS-55AT User manual

ASG, Division of Jergens, Inc.
15700 S. Waterloo Road | Cleveland, OH 44110-3898
Phone: [phone] | Fax: [phone]
Email: [e-mail] | Web: www.asg-jergens.com Page 1 of 3
PS-55AT
User Manual
• Please read this operation manual before using the power supply for correct and safe use
• The power supply shall be used with correct input of voltage
• The power supply shall be used in a place of good ventilation
• Please put the power supply in a clean and dry place, which is far away from oil, gas, noise and high voltage site
• Please make sure the power supply is grounded in use
• Please return to ASG for any repairs
• The power supply shall be put at a place where it is clearly seen, easy to move and convenient for maintenance
Note
Product Specications
Front Panel
© 2017 Jergens, Inc. All Rights Reserved | Revision Date: 2/23/2017
Power Switch HI/LOW: rotary speed voltage
switch, may change output voltage
of the electric driver by 30V/20V
Electric Driver Power Cord Socket:
please use cord supplied with the
screwdriver
Signal State Indicator Light:
• Start light on while start
signal is applied
• Stop light on while stop
signal is applied
• Finish light on when
clutch has activated
ASG Number 65707
Model Number PS-55AT
Size 7 x 3.5 x 3.3 in. (180 x 90 x 85 mm)
Weight 6 lb. (2700 g)
Input Voltage AC 110V or 230V 50/60Hz
AC Plug Cord Length 6 ft. (1.8 m)
Output Voltage DC 30/20V HI/LOW Max 2.5A

ASG, Division of Jergens, Inc.
15700 S. Waterloo Road | Cleveland, OH 44110-3898
Phone: [phone] | Fax: [phone]
Email: [e-mail] | Web: www.asg-jergens.com Page 2 of 3
PS-55AT
User Manual
Backboard
Power Supply Signal Time Scale
© 2017 Jergens, Inc. All Rights Reserved | Revision Date: 2/23/2017
Output/Input Signal
Terminal: controls
start and stop of
electric driver, and
clutch output signal Power Cord Socket
Fuse Jack, 2A/110V or 1A/230V
Input Voltage
Selection Switch:
providing choice of
110V/230V
T1 Turn on the power and start the power supply at least 2 seconds after the power is off (Robotic Operation)
T2 Input the signal to start the electric driver at least 2 seconds after the power supply is started (Robotic Operation)
T3 Indicating the start signal of the electric driver, which shall exceed 0.5 second
T4 Indicating the run time of the electric driver, which varies with the locking time
T5 The clutch signal of the electric driver
T6 Signal output by the backboard (Finish) of the power supply when the clutch operates, lasting for a period from the time when the clutch activates until the
input of Stop signal
T7 Indicating the stop signal (required to be longer than 0.5 second), which is explained as follows:
• If the electric driver is running, input of this signal may stop the electric driver before a clutch signal is seen
• If the clutch activates, the signal may open Finish output (Open)
• When the Start signal exists, Stop signal will not be accepted. A minimum interval of 0.5 second is required between the two signals
T8 The interval between the stop signal and start signal should be longer than 0.5 second

ASG, Division of Jergens, Inc.
15700 S. Waterloo Road | Cleveland, OH 44110-3898
Phone: [phone] | Fax: [phone]
Email: [e-mail] | Web: www.asg-jergens.com Page 3 of 3
PS-55AT
User Manual
Input Signal
Output Signal
© 2017 Jergens, Inc. All Rights Reserved | Revision Date: 2/23/2017
Relay of Contact Rating
Rate Load AC110V 0.5A , DC24V1A
Max. Allowable Voltage 125VAC, 30VDC
Max. Allowable Current 1A