Ashley M9X432 User manual

PAIRING YOUR NEW SIERRA
SLEEP POWER BASE BY
ASHLEY
M9X432,M9X442/442A,
M9X532, M9X542/542A,
M9X632, M9X642A/642A
A STEP BY STEP GUIDE

POWER SUPPLY (M9X432 & M9X442/442A
1. CONNECT THE POWER SUPPLY CORD INTO THE POWER
SUPPLY AND PLUG INTO AN OUTLET (MAKE SURE IT IS
CONNECTED TO THE POWER BASE)
2. UNPLUG THE POWER SUPPLY CABLE FROM THE
POWER SUPPLY (DO NOT UNPLUG FROM WALL
OUTLET)

REMOTE SYNC M9X432 & M9X442/442A
3. HOLD DOWN THE “HOME” AND “DOWN” BUTTONS
SIMULTANEOUSLY UNTIL THE BLUE BACKLIGHT DISSAPERS
(WITHIN 5-7 SECONDS)

4. PLUG THE POWER SUPPLY CORD BACK INTO THE
POWER SUPPLY. WITHIN SEVERAL SECONDS YOU WILL
HEAR A LONG CHIRP FOLLOWED BY A SHORT CHIRP.
YOUR BASE IS NOW SYNCED AND READY TO GO!

POWER SUPPLY (M9X532 & M9X542/542A
1. CONNECT THE POWER SUPPLY CORD INTO THE POWER
SUPPLY AND PLUG INTO AN OUTLET (MAKE SURE IT IS
CONNECTED TO THE POWER BASE)
2. UNPLUG THE POWER SUPPLY CABLE FROM THE
POWER SUPPLY (DO NOT UNPLUG FROM WALL
OUTLET)

REMOTE SYNC M9X532 & M9X542/542A
3. HOLD DOWN THE “HOME” AND “DOWN” BUTTONS
SIMULTANEOUSLY UNTIL THE BLUE BACKLIGHT DISSAPERS
(WITHIN 5-7 SECONDS)

4. PLUG THE POWER SUPPLY CORD BACK INTO THE POWER
SUPPLY. WITHIN SEVERAL SECONDS YOU WILL HEAR A LONG CHIRP
FOLLOWED BY A SHORT CHIRP. YOUR BASE IS NOW SYNCED AND
READY TO GO!

POWER SUPPLY (M9X632 & M9X642/642A
1. CONNECT THE POWER SUPPLY CORD INTO THE POWER
SUPPLY AND PLUG INTO AN OUTLET (MAKE SURE IT IS
CONNECTED TO THE POWER BASE)
2. UNPLUG THE POWER SUPPLY CABLE FROM THE
POWER SUPPLY (DO NOT UNPLUG FROM WALL
OUTLET)

REMOTE SYNC M9X632 & M9X642 &642A
3. HOLD DOWN THE “SELECT” BUTTON UNTIL YOU SEE
THE WORD “PAIR” ON THE SCREEN

4. PLUG THE POWER SUPPLY CORD BACK INTO THE POWER
SUPPLY. WITHIN SEVERAL SECONDS YOU WILL HEAR A LONG
CHIRP FOLLOWED BY A SHORT CHIRP.
5. ONCE THE POWER SUPPLY IS PLUGGED BACK IN YOU
WILL SEE AN “ELCO” NOTIFICATION. YOUR POWER BASE
IS READY TO GO!

SELECTING YOUR MEMORY PRE SETS
TO CUSTOMIZE YOUR MEMORY PRE SET, PRESS
AND HOLD DOWN THE LIGHT BUTTON NEXT TO
PRE SET NUMBER 2 (WAIT 5-7 SECONDS) YOU
WILL SEE THE SCREEN FLASH “SAVE”. SELECT PRE
SET 1 OR 2. THAT’S IT YOUR MEMORY SETTING IS
COMPLETE!

HOW TO ASSEMBLE YOUR KING
POWER BASE BY ASHLEY
1. THE M9X KING BASES ARRIVE IN
TWO BOXES AS SHOWN.
PLEASE MAKE SURE YOUR
CUSTOMER KNOWS TO ALLOW
ROOM FOR ASSEMBLY IN THEIR
HOME.
2. OPEN BOTH BOXES AND PLACE EACH
UNIT FACE UP ALLOWING THE
MECHANICS TO SHOW.

KING HEAD UNIT WITH “HEAD MOTOR”
1. TAKE THE BOX LABELED
“HEAD MOTOR” OUT OF
THE BOX

1. CUT THE ZIP TIES UNDERNEATH
THE “BOTTOM BASE” ON BOTH
SIDES TO EXTEND THE ARM TO
ATTACH THE HEAD MOTOR.
2. CONNECT
“HEAD MOTOR B”
TO THE PIN UNDER
THE BOTTOM BASE
LABELED “B”
(NOTE THIS IS WHY YOU
NEED TO CUT THE ZIP TIES
IN ORDER TO MOVE THE
ARM)

BOLTING THE TWO BASES AND HEAD MOTOR
TO PIN “A”
1. BOLT THE HINGES FROM THE “HEAD BASE”
TO THE “BOTTOM BASE” (THE 4 BOLTS ARE
LOCATED IN THE BOX WITH THE CASTER LEGS)
AFTER THE HINGES ARE BOLTED, ATTACH THE
OTHER HALF OF THE HEAD MOTOR TO
PIN “A” (SEE PICTURE)
BOLTS FOR HINGES