Astria Tuscan36P2 User manual

PFS
®
USC
Installation and Operation Instructions
Astria® Residential and Outdoor Wood-
Burning Fireplace
Models
Tuscan36P2 Tuscan36P3
P126764-01
P/N 126764-01 Rev. D 10/2015 Report No. F10-078
SAVE THIS BOOK
This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also
contains information that will enable you to obtain replacement parts or accessory items when needed. Keep
it with your other important papers.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.
This wood burning fireplace complies with UL127
CAN/ULC-S610-M87 standard as a FACTORY
BUILT FIREPLACE.
Ce foyer au bois est conforme aux UL 127 CAN/ULC-
S610-M87 norme comme une USINE CONSTRUITE
CHEMINÉE.
This fireplace is approved for use as a wood burning fireplace or for use with a vented gas log approved to
ANSI Z21.60 or Z21.84 standards or for use with a vent-free gas log heater approved to ANSI Z21.11.2 standard .
An IHP hood must be installed when using a vent-free log heater (see Accessories, page 19).
FOR CANADA: The authority having jurisdiction
(such as the municipal building department, fire
department, etc.) should be contacted before
installation to determine the need to obtain a permit.
POUR LE CANADA: L’autorité compétente (comme le
service municipal du bâtiment, les pompiers, etc.) doit
être contacté avant l’installation afin de déterminer la
nécessité d’obtenir un permis.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or
mobile home, where not prohibited by local codes.
This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace
system. Please read and understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of
the fireplace system, including but not limited to the fireplace, chimney components and accessories, may void the
warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous installation.
IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS: INSTALL THIS FIREPLACE IN A SQUARE
AND PLUMB CONDITION, USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.

Astria.US.com 126764-01D2
SAFETY
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury,
property damage or loss of life. Refer to this manual
for assistance or additional information. Consult a
qualified installer or local distributor.
IMPORTANT: Check local codes before installing this
fireplace.
Before beginning installation of this fireplace, read these instructions
through completely.
• This INNOVATIVE HEARTH PRODUCTS (IHP) replace and its
components are safe when installed according to this installa-
tionmanual.UnlessyouuseIHPcomponents,whichhavebeen
designed and tested for the fireplace system, you may cause a fire
hazard.
• TheIHPwarrantywillbevoidedbyandIHPdisclaimsanyrespon-
sibility for the following actions.
a. Modification of the fireplace, components, doors, air inlet system
and damper control.
b.Useofanycomponentpartnotmanufacturedorapprovedby
IHPincombinationwithanIHPreplacesystem.
Proper installation is the most important step in ensuring safe and
continuousoperationofreplace.Consultthelocalbuildingcodes
as to the particular requirements concerned with the installation of
all factory built fireplaces.
WARNING: Do not install a fireplace insert in this
box unless the manufacturer's instructions with the
insert specifically state this fireplace has been tested
for use with this insert.
TABLE OF CONTENTS
Safety.............................................................................................2
Specications.................................................................................4
FireplaceInstallation ......................................................................5
VentingInstallation ........................................................................7
OptionalGasLineInstallation ......................................................12
OperationandMaintenanceGuidelines........................................13
TechnicalService .........................................................................14
ReplacementParts.......................................................................14
Parts ............................................................................................15
Accessories..................................................................................18
Warranty ......................................................................................23
Thank you for your purchase. We appreciate your
business!
Please carefully read and follow all instructions in this manual. Pay
special attention to all warnings and safety information.
Following these safety, care, and operation instructions will help
ensure many years of dependable and enjoyable service from your
fireplace.
Register your product online today!
To help us keep you up-to-date on product information and of-
fers, please take a few moments to register your product online
atAstria.US.com
Please read and understand these instructions before installing
or operating.
FOR YOUR SAFETY
•Donotstoreorusegasolineoranyotherammable
vapors or liquids in the vicinity of this or any other
appliance.
•Duetohightemperatures,theapplianceshouldbe
located out of traffic and away from furniture and
draperies.
•Donotplaceclothingorotherammablematerials
on or near the appliance.
•Neverleavechildrenunattendedwhenareisburn-
ing in the fireplace.
WARNING: Use solid wood or processed solid fuel
firelogs only. When processed wood fuel fire logs are
used, do not poke or stir the logs while they are burning.
Use only fire logs that have been evaluated for the ap-
plication in fireplace and refer to fire log warnings and
caution markings on packaging prior to use.
This fireplace is not intended to be used as a substitute
for a furnace to heat an entire home. Use for supple-
mental heat only.
Overfiring of a fireplace is a condition where excessive
temperaturesarereached,beyondthedesigncapabilities
of theappliance. Thedamage thatoccursfrom overfiring
isnotcoveredunderthemanufacturer’slimitedwarranty.

Astria.US.com
126764-01D 3
SAFETY Continued
WARNING: CONTINUED OVERFIRING CAN PER-
MANENTLY DAMAGE YOUR FIREPLACE SYSTEM.
SOME EXAMPLES OF CONDITIONS THAT COULD
CAUSE OVERFIRING ARE:
• BURNINGQUANTITIESOFSCRAPLUMBER,PINE
BRANCHES, PAPER OR CARDBOARD BOXES
WHICHEXCEEDTHEVOLUMEOFTHENORMAL
LOGFIRE.
• BURNINGTRASH,CHEMICALSORCHEMICALLY
TREATEDCOMBUSTIBLES.
Disposal of Ashes
Ashes should be placed in a metal container with a
tight-fitting lid. The closed container of ashes should
beplacedonanoncombustibleoororontheground,
well away from all combustible materials, pending
final disposal. If the ashes are disposed of by burial
in soil or otherwise locally dispersed, they should be
retained in the closed container until all cinders have
thoroughly cooled.
WHEN USING THE DECORATIVE APPLIANCE, THE
FIREPLACE DAMPER MUST BE SET IN THE FULLY
OPEN POSITION.
Never use gasoline, gasoline-type lantern fuel, kero-
sene,charcoallighteruid,orsimilarliquidstostart
or ’freshen up’ a fire in this fireplace. Keep all such
liquids well away from the fireplace while it is in use.
Use SOLID WOOD only for fuel. It is best to use dry
and well seasoned hardwood. Softwoods tend to burn
veryquickly.DONOTusetreatedwood,charcoal,coal,
trash,driftwoodorwoodsthathavebeendippedintar,
pitch, pine tar, creosote, etc. Wood products made
with synthetic binders, such as plywood, produce ab-
normally high temperatures and sputtering, smoking
fires. When burning artificial logs, please read and
follow the instructions provided by the manufacturer.
Never burn treated construction lumber or scraps.
These woods burn excessively hot and may contain
chemicals used to treat insects and fungus. When
burned,thesechemicalscanposeasignificanthazard.
WARNING: BURNING IMPROPER FUEL (I.E.
CHARCOAL) CAN RESULT IN CARBON MONOXIDE
POISONING, WHICH MAY LEAD TO DEATH!
Carbon Monoxide Poisoning – Early signs of carbon
monoxidepoisoningresembletheuwithheadaches,
dizziness, or nausea. If you have these signs, get
fresh air at once! Have the appliance inspected by a
qualified service technician. Some people are more
affected by carbon monoxide than others. These
include pregnant women, people with heart or lung
diseaseoranemia,thoseundertheinuenceofal-
cohol, and those at high altitudes.
Ventilation Requirements - Provide adequate air for
combustion. The fresh air requirements of this ap-
pliance must be met within the space where it will
be installed.
Smoke Detectors - Since there are always several
potential sources of fire in any home, we recommend
installing smoke detectors. If possible, install the
smoke detector in a hallway adjacent to the room (to
reduce the possibility of occasional false activation
fromtheheatproducedbytheappliance). Ifyourlocal
coderequiresasmokedetectorbeinstalledwithinthe
same room, you must follow the requirements of your
localcode.Checkwithyourlocalbuildingdepartment
for requirements in your area.
Creosote – Formation and Need for Removal
Whenwood isburned slowly, itproduces tarand other
organicvapors,whichcombinewithexpelledmoisture
to form creosote. The creosote vapors condense in
the relatively cool chimney ue of a slow-burning
fire. As a result, creosote residue accumulates on
theuelining.Whenignitedthiscreosotemakesan
extremely hot fire.
The chimney shall be inspected at least twice a
year during the heating season to determine when a
creosote buildup has occurred. When creosote has
accumulated(1/8"[3mm]ormore)itshallberemoved
to reduce the risk of a chimney fire.

Astria.US.com 126764-01D4
SPECIFICATIONS
0" TO
BOTTOM
OUTSIDE
AIR (LEFT
SIDE ONLY)
3/4"
AIR
SPACE
BACK
AND
SIDES
HEARTH
EXTENSION
51" X 16"
8" EACH
SIDE
NOT LESS
THAN 12" TO
PERPENDICULAR
SIDEWALL
1" AIRSPACE
TO COMBUSTIBLE
MATERIAL
COMBUSTIBLE
WALL BOARD
0" TO
TOP
SPACERS
NO COMBUSTIBLE
MATERIAL ON FACE
GAS LINE
KNOCK
OUTS
AIR KIT
KNOCK OUT
GAS LINE
KNOCK
OUTS
ELECTRICAL
OUTLET
LEFT SIDE
RIGHT SIDE
37"
41"
35"
21"
8"
22"
1"
41"
1"
29"
20 1/2"
91/8"
91/8"
71/8"
31/2"
31/2"
83/4"
83/4"
11 1/4"
14 1/4"
41 1/4"
32 1/2"
11 3/4"
5/8"
11 1/2"
14 1/2"
SQUARE CHASE-TOP
TERMINATION
ROUND TOP TERMINATION
CAUTION: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/
ROOF MUST BE MAINTAINED.

Astria.US.com
126764-01D 5
FIREPLACE INSTALLATION
4. Checkthelevelofthereplaceandshimwithsheetmetalifneces-
sary.
5. Before securing fireplace to prepared framing, the ember protector
(provided)mustbeplacedbetweenthehearthextension(notsup-
plied)andunderbottomfrontedgeofreplacetoprotectagainst
glowingembersfallingthrough.Ifreplaceistobeinstalledona
raisedplatform,aZ-typeemberprotector(notsupplied)mustbe
fabricated to fit your required platform height. The ember protec-
torshouldextendunderreplaceaminimumof11/2". The ember
protectorshouldbemadeofgalvanizedsheetmetal(28gauge
minimum)topreventcorrosion.
6. Usingscrewsornails,securereplacetoframingthroughanges
located on sides of fireplace.
DRAIN PAN (DP36)
For outdoor installations, the fireplace enclosure must allow for
adequatedrainageandfreshairventilation.Itisrecommendedthat
a sealed, corrosion resistant catch pan with provision for drainage
beinstalledunderthereplacewithinthereplaceenclosure(see
Accessoriesonpage19).
41 3/4"
41 3/4"21 7/8"
Figure 1 - Framing Dimensions
Maintain 3/4"
Clearance at
Sides and
Back of
Fireplace
3/4" Clearance Not
Required at Nailing Flanges
52 1/4"
17 3/8"
73 7/8"
24 1/2"
Figure 2 - Corner Installation
SELECTING LOCATION
WARNING: DO NOT INSTALL IN SLEEPING ROOM
OF MOBILE HOMES.
To determine the safest and most efficient location for the fireplace,
you must take into consideration the following guidelines:
1. Thelocationmustallowforproperclearances(seeFigures1and
2).
2. Consideralocationwherethereplacewillnotbe affectedby
drafts, air conditioning ducts, windows or doors.
3. A location that avoids the cutting of joists or roof rafters will make
installation easier.
4. Anoutsideairkitisavailablewiththisreplace(seeOptionalOutside
Air Kitonpage7).
MINIMUM CLEARANCE TO COMBUSTIBLES
Ceiling  40"minimum
Back and sides of fireplace 3/4" minimum*
Floor**  0"minimum
Perpendicular wall to opening 12" minimum
Topspacers  0"minimum
Mantel clearances see Mantels, page 6.
Chimneyouterpipesurface  1"minimum
*Notrequiredatnailinganges
**Seestep2ofFraming
WARNING: Do not pack required air spaces with
insulation or other materials.
Minimum/Maximum Chimney Height for Residential Installation
The minimum height of the chimney, measured from the base of
thereplacetotheuegasoutletofthetermination,is14.5feetfor
straightueorauewithoneelbowset.Themaximumdistance
between elbows is 6 feet. For systems with two elbow sets, the
minimumheightis22feet.Themaximumheightofanysystemis
50feet.Thismeasurementincludesthereplace,chimneysections
andtheheightoftheterminationassemblyattheleveloftheuegas
outlet(seeFigure18,page11).
Minimum/Maximum Chimney Height for Outdoor Installation
The minimum height of the chimney, measured from the base of the
replacetotheuegasoutletofthetermination,is71/2feet(minimum
of4feetofchimneypipesectionsrequiredforoutdoorinstallation).
FRAMING
1. Frame opening for fireplace using the dimensions shown in Figures
1 and 2.
2. If replace is to be installed directly on carpeting, tile or any
combustiblematerialotherthanwoodooring,thereplacemust
beinstalleduponametalorwoodpanelextendingthefullwidth
and depth of fireplace.
3. Setreplacedirectlyinfrontofthisopeningandslideunitback
untilnailingangestouchsideframing.

Astria.US.com 126764-01D6
OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F)
The installation of an outside air kit should be performed during the
roughframingofthereplaceduetothenatureofit'slocation.Outside
combustion air is accessed through a vented crawl space (AK4F) or
throughasidewall(AK4). SeeFigure22onpage13forinstructionof
operating air kit.
CAUTION: Combustion air inlet ducts shall not
terminate in attic space.
The maximum height for the air vent can not exceed
3feetbelowtheuegasoutletofthetermination.
HEARTH EXTENSION
Ahearthextensionprojectingaminimumof16"infrontofanda
minimum of 8" beyond each side of the fireplace opening is required
toprotectcombustibleoorconstructioninfrontofthereplace.
Fabricateahearthextensionusingamaterialwhichmeetsthefol-
lowing specifications: a layer of noncombustible, inorganic material
havingathermalconductivityofk=0.84BTUIN/FT,HR.F(orless)at
1"thick.Forexample,ifthematerialselectedhasaKfactorof0.25,
such as glass fiber, the following formula would apply:
0.25x1.0"=0.30"thicknessrequired
 0.84
Thermal conductivity "k" of materials can be obtained from the manu-
facturer or supplier of the noncombustible material. If the hearth
extensionistobecovered,use noncombustible material such as
tile, slate, brick, concrete, metal, glass, marble, stone, etc. Provide
ameanstopreventthehearthextensionfromshiftingandsealgap
betweenthereplaceframeandhearthextensionwithanoncom-
bustiblematerial(seeFigure3).
WARNING: Hearth extension is to be installed only
as shown in Figure 3.
Figure 3 - Hearth Extension
Seal Gap
Fireplace Front
Ember Protector
Fireplace Front
Raised Hearth
Fireplace Front
Elevated
Ember Protector
Ember Protector
Seal Gap
Hearth
Extension
MANTELS
Amantelmaybeinstalledifdesired(seeFigure4).Woodworksuch
as wood trims, mantels or any other combustible material project-
ing from the front face must not be placed within 12" of the fireplace
opening.Combustiblematerialsabove12"andprojectingmorethan
11/2" from the fireplace must not be placed less than 15" from the
topopeningofthereplace(NFPA211, Section-Clearancefrom
CombustibleMaterial).
Mantels or any other combustible material also may come up to the
side edge of the black metal face of the fireplace just as long as the
projection from the front face fall within the limit shown in Figure 4.
12 1/4" Ref.
6"
Ref.
12" Min.
9" Min.
11/2" Max.
3" Nom.
33°
Combustible
Material
Safe
Zone for
Projection of
Combustible
Materials
Fireplace Opening
Upper
Section of
Fireplace
Figure 4 - Mantel Clearances to Combustible Material
FIREBOX
SAFE ZONE
TopViewofFireplace
2" Max.
3.0"
Min. to
Perpendicular
Side Wall
12"
8.0"
33°
Combustible
Material Must
Not Overlap
Front Face
FIREPLACE INSTALLATION Continued

Astria.US.com
126764-01D 7
Figure 6 - Lineal Gain
Hemmed
End
8" Stainless
Inner Pipe
12 3/8" Galvanized
Outer Pipe
WARNING: The opening in collar around chimney
at top of fireplace must not be obstructed. Never use
blown insulation to fill chimney enclosure.
LINEAL GAIN
PART NO. DESCRIPTION GAIN
36" Fireplace 40 "
12-8DM
12-8HT PipeSection 105/8
"
18-8DM
18-8HT PipeSection 16 5/8
"
24-8DM
24-8HT PipeSection 23 5/8
"
36-8DM
36-8HT PipeSection 34 5/8
"
48-8DM
48-8HT PipeSection 46 5/8
"
RT-8DM RoundTermination 6 7/8 "
*
RTL-8DM RoundTermination 7 3/4 "
*
RTT-8DM RoundTerminationwithSlipSection 6 7/8
" to
23 1/8"*
RTTL-8DM RoundTerminationwithSlipSection 8 1/2
" to
21 1/2"*
ET-8DM SquareChase-Top 12 "
*
ETO-8DM SquareChase-TopwithMesh 12 "
*
ETL-8DM SquareChase-TopwithSlipSection 7" to
15"*
ETLO-8DM SquareChase-TopwithMesh&SlipSec-
tion
12 " to
25 1/2" *
*Thelinealgainfortheterminationsismeasuredtotheuegas
outlet height.
Figure 5 - Outside Air Kit
Secure to Collars with Metal Tape, Screws
or Straps (Min. of 1/4" x 20" in size)
Air Inlet
Location
Must Allow
For Bushes
or Snow
Vent Hood
Required for
Wall Installation
Air Inlet
Eyebrow
Vented Crawl Space
(Check Local Codes
Before Installing in a
Vented Crawl Space)
VENTING INSTALLATION
CHIMNEY PIPE
WARNING: Label part number 900599-01 must
be applied by the installer to all chimney pipe
sections but is not required on sections that will
be visible after the installation is complete. Label
must wrap around the circumference of the pipe.
See accessories, page 19 for Kit F2659.
TheIHPchimneysystemconsistsof12",18",24",36"and48"snap-
lock,double-wallpipesegments,plannedformaximumadaptabilityto
individual site requirements. Actual lengths gained after fitting overlaps
mustbetakenintoconsideration(linealgain)andaregiveninthelineal
gainchart(seeFigure6).Linealgainistheactualmeasurablelengthof
apartaftertwoormorepartsareconnected.ForCanada,usechimney
partsdesignated"HT".
A SSEMBLY AND INSTALLATION OF DOUBLE WALL CHIMNEY
SYSTEM
Eachdoublewallchimneysectionconsistsofagalvanizedouterpipe,
astainlesssteelinneruepipeandawirespacer.Thepipesections
must be assembled independently as the chimney is installed.
When connecting chimney directly to the replace, the inner ue
pipe section must be installed first with the lanced side up. The outer
pipesectioncanthenbeinstalledovertheuepipesectionwiththe
hemmed end up. Press down on each pipe section until the lances
securely engage the hem on the fireplace starter. The wire will as-
sure the proper spacing between the inner and outer pipe sections.
Continuetoassemblechimneysections as outlined, making sure

Astria.US.com 126764-01D8
VENTING INSTALLATION Continued
Figure 7 - Typical Offset Terminations
Return
Elbow
Offset
Elbow
Return
Elbow
Offset
Elbow
6' Max.
6' Max.
6' Max.
6' Max.
6' Max.
6' Max.
Return
Elbow
Offset
Elbow
Offset
Elbow
Return
Elbow
ABC
Offset
Elbow
Ceiling
Support Pipe
12S-8DM
Return
Elbow
Figure 8 - Ceiling Support Pipe 12S-8DM
2" Min.
Straps Straps
Straps
Straps
Detail A
Return Elbow
Detail B
Angle
Firestop
See Detail A
See Detail B
Ceiling Support
Pipe 12S-8DM
that both the inner and outer pipe sections are locked together. When
installing double wall snap-lock chimney together, it is important to
assurethejointbetweenthechimneysectionsislocked.Checkby
pulling chimney upward after locking. The chimney will not come
apartifproperlylocked.Itisnotnecessarytoaddscrewstokeepthe
chimneytogether(exception-seeFigure9,page9).
The height of a vertical chimney pipe supported ONLY by the
replace,mustnotexceed20feet.Chimneyheightsabove20feet
must be supported.
USING ELBOW OFFSETS (30E-8DM)
1. To achieve desired offset, you may install combinations of 12",
18",24",36"and48"lengthofdoublewallpipe(seeoffsetchart
andFigure7).
2. Chimneyweightaboveoffsetrestsonreturnelbow.Strapsmust
besecurelynailedtoraftersorjoists(seeFigure8,detailsAand
B).
3. Maximumlengthofpipebetweensupports(returnelbowor12S-
8DM)is6'ofanglerun.Maximumoftwo6'anglerunsections
perchimneysystem(seeFigure7).
4. All pipe connections between offset and return must be secured
withtwoscrewsonouterpipeonly(seeFigure9,page9).Donot
penetrate inner stainless.

Astria.US.com
126764-01D 9
Figure 9 - Elbow Offset
Figure 10 - Firestop Spacer with Living Space Above Ceiling
Figure 11 - Firestop Spacer with Attic Space Above Ceiling
Existing
Ceiling
Frame
Firestop
Spacer
Screws or
Staples
(Min. of 8)
Firestop
Spacer
Screws or Staples
(Min. of 8)
Existing
Ceiling
Frame
B
A
Screws
VENTING INSTALLATION Continued
FIRESTOP SPACERS (3600FS-8DM-1)
Firestop spacers are required at each point where the chimney penetrates
aoorspace.Theirpurposeistoestablishandmaintaintherequired
clearance between the chimney and the combustible materials. When
the pipe passes through a framed opening into a living space above, the
restopmustbeplacedontotheceilingfrombelowasshowninFigure10.
Theyalsoprovidecompleteseparationfromoneoorspacetoanother
or attic space as required by most codes. When the double wall pipe
passes through a framed opening into an attic space, the firestop must
beplacedintoanatticoorasshowninFigure11.
IMPORTANT NOTICE
Whenpenetratingaceilingintoanattic,afirestopthimble(38FST
or FST30) is required to avoid intrusion by insulation and recom-
mended to negotiate a joist (see Figure 11a).
Figure 11a - Firestop Thimble
Thimble
38FST or
FST30
Firestop
OFFSET CHART (22-50 FT. SYSTEM HEIGHT)
OFFSET RISE CHIMNEY LENGTH
A B 48" 36" 24" 18" 12"
4 3/8" 16 3/8"ELBOW SET ONLY
9" 25 3/4" 1
11 7/8" 31" 1
15" 37 3/8" 1
16 3/4"401/2" 1 1
20" 47 1/8" 1
22 5/8" 52 1/8" 1 1
25 1/2" 57 7/8" 1
27 5/8" 62" 1 1
303/8" 67 1/4" 1 1
33" 72 5/8" 1 1
35 3/4" 78" 2
37 7/8" 82" 1 1 1
41 1/4" 88 5/8" 1 1
43 3/8" 92 3/4" 2 1
46 5/8" 99 3/8" 2
48 3/4"1031/2" 1 1 1
51 1/2"1087/8" 2 1
54 1/4" 114 1/8" 2 1
57" 119 1/2" 1 2
59" 123 5/8" 2 1 1
61 3/4" 129" 1 2 1
64 1/2" 134 3/8" 1 2 1
67 1/4" 139 5/8" 4

Astria.US.com 126764-01D10
14
3
/
8
"
(36.5 cm)
30"
(76.2 cm)
1"
(2.5
cm)
1"
(2.5
cm)
Minimum Measurements
1"
(2.5 cm)
Opening "A"
Pitch Slope Opening "A"
Max.
Used Flashing
Model No.
Flat 0° 15" V6F-8DM
0-6/12 26.6° 16 1/8"V6F-8DM
6/12-
12/12 45.0° 203/8"V12F-8DM
Figure 12 - Roof Opening Measurements
Nail Only
Outer
Perimeter
of Flashing
Storm Collar
Flashing
Cone
Underlap Shingles
at Bottom
Overlap
Shingles Top
and Sides Only
Figure 13 - Flashing Installation
Figure 14 - Storm Collar
Chimney
Pipe
Waterproof
Caulk
Storm
Collar Flashing
VENTING INSTALLATION Continued
PENETRATING ROOF
To maintain a 1" clearance to the pipe on a roof with a pitch, a rect-
angular opening must be cut.
1. Determine center point through which pipe will penetrate roof.
2. Determine center point of roof. Pitch is the distance the roof drops
over a given span, usually 12". A 6/12 pitch means that the roof
drops 6" for each 12" one measure horizontally down from the
roof rafters.
3. Useroofopeningchart(Figure12)todeterminethecorrectopen-
inglengthandashingrequired.
4. Remove the shingles around opening measured. Cut out this
section.
5. Addnextsectionsofpipeuntilendpenetratesroofline.Checkto
seethattheproperclearancesaremaintained.Extendchimneyby
addingsectionsofdoublewallpipeuntilpipeisminimumof30"
above the highest point of the roof cutout. Termination and chimney
mustextendaminimumof36"abovethehighestpointwhereit
passes through the roof.
FLASHING INSTALLATION (V6F-8DM OR V12F-8DM)
Determinetheashingtobeusedwiththeroofopeningchart.Slide
ashingoverpipeuntilbaseisatagainstroof.Replaceasmany
shinglesasneededtocoverexposedareaandashingbase.Secure
inpositionbynailingthroughshingles(seeFigure13).DONOTNAIL
THROUGHFLASHINGCONE.
Installing Flashing on a Metal Roof
Wheninstallingashingonametalroof,itisrequiredthatputtytapebe
usedbetweentheashingandroof.Theashingmustbesecuredtothe
roofusing#8x3/4"screwsandthensealedwithroofcoatingtoprevent
leakage through screw holes. A roof coating must also be applied around
perimeterofashingtoprovideaproperseal.
Storm Collar Installation (SC1 or SC2)
Place storm collar over pipe and slide down until it is snug against the open
edgeoftheashing(seeFigure14).UseSC1forallroundterminations
andSC2forallterminationswithslipsections.Applywaterproofcaulk
around the perimeter of the collar to provide a proper seal.
Terminations/Spark Arrestor
The fireplace system must be terminated with the listed round top or
chaseterminations.Inanycase,refertotheinstallationinstructions
supplied with the termination. The termination approved for this fire-
placearetheRT-8DMandRLT-8DMthatcanbeusedforashingor
chaseandET-8DM,ETO-8DM,ETL-8DMandETLO-8DMforchasestyle
terminationonly.Figure15showsanRLT-8DMroundtoptermination.
CAUTION: Do not seal openings on the rooftop
ashing.Followtheinstallationinstructionsprovided
with the termination being used.
Terminationswith16"slippipesectionsareavailable.TheRTT-8DM
andRLTT-8DMareapprovedforashinginstallations.Whenneeded,
these adjustable terminations may be used in combination with the
pipe assembly to achieve the correct chimney height.
Note:Intherareinstancethereisaproblemwiththesidedrivenrain
orwindorthechimneyisnotdraftingproperly,anADS-8DM(Anti-
DraftShield)canbeusedwithroundterminations.

Astria.US.com
126764-01D 11
Figure 15 - Termination
Attach Bracket
Tabs to
Outer Pipe
(3 Places)
Secure with
Screws
RLT-8DM
Level of
Flue Gas
Outlet
Caulk
Collar
Flashing
Underlap
Shingles
Bottom Only
Overlap
Shingles Top
and Sides
24" Min.
24" Min.
18"
Min.
Typ.
Figure 16 - Multiple Chase Installation
CHASE INSTALLATIONS
Instructionsforchaseinstallationsareincludedwiththechasestyle
terminationchosen.Inamultiplechaseinstallation,besuretoprovide
adequate distance between terminations to prevent smoke spillage
from one termination to another. We suggest that terminations be
separated at least 24", center to center and stacked at a vertical height
differenceof18"(seeFigure16).
Note: Ifadecorativeshroudistobeinstalled,contactthemanufac-
turer for specifications.
10 FOOT RULE
Alluegasoutletchimneyterminationsmustextendaminimumof
3 feet in height above the highest point where it passes through the
roof and must be at least 2 feet above the highest point of the roof
thatiswithinahorizontaldistanceof10feet(seeFigure17).
FINISHING FIREPLACE
Combustiblematerials,suchaswallboard,sheetrock,drywall,ply-
wood, etc. may make direct contact with sides and top around the
replaceface.Itisimportantthatcombustiblematerialsdonotoverlap
the face itself. Brick, glass, tile or other noncombustible materials
may overlap the front face provided they do not obstruct essential
openings like louvered slots or any other opening. When overlapping
with a noncombustible facing material, use only noncombustible
mortar or adhesive.
VENTING INSTALLATION Continued
Figure 17 - 10 Foot Rule
30E-8DM
EFFECTIVE HEIGHT
OF TERMINATION CAP
EFFECTIVE HEIGHT
OF TERMINATION CAP
EFFECTIVE HEIGHT
OF TERMINATION CAP
EFFECTIVE HEIGHT
OF TERMINATION CAP
MINIMUM
HEIGHT
14.5 FT.
MINIMUM
UP TO
6FT. MAX.
UP TO
6FT. MAX.
HEIGHT
14.5 FT.
MIN. HEIGHT
OF 22 FT. (WITH
2 ELBOW SETS)
MAX. HEIGHT OF
50 FT.
MAX. HEIGHT
50 FT.
(ANY SYSTEM)
30E-8DM
Figure 18 - Typical Residential Installations
10'
2' Min.
10'
3' Min.
2' Min. 3' Min.
Level of
Flue Gas
Outlet

Astria.US.com 126764-01D12
OPTIONAL GAS LINE INSTALLATION
Figure 19 - Gas Line Knockout
Side
Firebrick
Finished
Side
Refractory
Knockout
Plug
Outside of
Fireplace
Gas Line
Conduit
Insulation
Gas
Conduit
Cover
1/2" Dowel
Gas line hook up should be done by your supplier or a qualied
service person.
Note: Before you proceed, make sure your gas supply is turned off.
Useonlya1/2"blackironpipeandappropriatettings.
1. Removeknockoutindentationonrefractoryorrebrickwalllo-
catedabovetherefractoryhearthoor.Theknockoutindentation
must be firmly tapped with any solid object such as a 1/2" dowel
untilitisreleased.Removefragmentedportionsofrefractory(see
Figure19).
2. Removegaslinecoverplatelocatedoneithersideofreplaceand
pulloutinsulationfromgaslineconduitsleeve.Saveinsulation
forreuse.Replacescrews.
3. Runa1/2"blackirongaslineintothereplacethroughtherear
atgaslineconduitsleeve(ifusingaraisedplatform,addheight).
Provide sufficient gas line into fireplace chamber for fitting con-
nection(seeFigure20).Note:Secureincominggaslinetowood
framing to provide rigidity for threaded end.
4. Repackinsulationaroundgaslineandintosleeveopening.Seal
any gaps between gas line and refractory knockout hole with
refractorycementorcommercialfurnacecement,Installthegas
appliance or cap-off gas line if desired.
CAUTION: All gas piping and connections must be
tested for leaks after the installation is completed.
After ensuring that the gas valve is on, apply soap and
water solution to all connections and joints. Bubbles
formingshowa leak.Correctall leaksatonce. DONOT
USEAN OPEN FLAMEFOR LEAK TESTING ANDDO NOT
OPERATE ANY APPLIANCE IF A LEAK IS DETECTED.
LEAK TESTING SHOULD BE DONE BY A QUALIFIED
SERVICE PERSON.
Note:AnIHPhoodmustbeinstalledwhenusinganunventedgas
logset(seeAccessoriesonpage19).
WARNING: Do not operate an unvented gas log set in
this fireplace with the chimney removed.
Ifyouinstalladecorativegasappliance(ventedgaslog),thedeco-
rativegasappliancemustcomplywiththeStandardforDecorative
GasApplianceforInstallationinSolidFuelBurningFireplaces,ANS
Z21.60orZ21.84andshallalsobeinstalledinaccordancewiththe
NationalFuelGasCode,ANSI7223NFPA54latestedition.
WARNING:Toavoidtheriskofdamagingthefireplace
materials and increasing the risk of spreading a fire,
do not use the fireplace to cook or warm food.
Seal
Opening
with
Refractory
Cement
Outside of
Fireplace
Gas
Line
Conduit
Repack
Insulation
Incoming
1/2" Black
Iron Pipe
Side
Firebrick
Finished
Side
Provide Enough Threaded
End for Fitting Connection
Figure 20 - Gas Line Installation
WARNING: If the fireplace has been used for wood
burning, the firebox and chimney must be cleaned
of soot, creosote and ashes be a qualified chimney
cleaner. Creosote will ignite if heavily heated.
WARNING: When using a decorative vented gas log,
the damper must be removed or permanently locked in
the fully open position and the glass doors must be in
the fully open position.

Astria.US.com
126764-01D 13
Doors Fully Closed
Fireplace Front
Doors
Fully Opened
Fireplace Front
OPERATION AND MAINTENANCE GUIDELINES
Figure 21 - Glass Doors
GLASS DOORS
Glassdoorsareoptionalwiththereplace.Whenthereplaceisin
operation, doors must be fully opened or fully closed position only
orarehazardmaybecreated(seeFigure21).
A fireplace equipped with glass doors operates mush differently
than a fireplace with an open front. A fireplace with glass doors has
alimitedamountofairforcombustion.Excessiveheatwithinthe
fireplace can result if too large a fire is built or if the combustion air
gate is not completely open.
The following tips should be followed to assure that both the fireplace
and the glass door retain their beauty and function properly. Both the
uedamperandtheglassdoorsmustbefullyopenedbeforestarting
the fire. This will provide sufficient combustion air and maintain safe
temperaturesintherebox.
IMPORTANT: The glass must be allowed to warm slowly and evenly.
Thetemperedglasswillwithstandagradualtemperatureriseto550°
F,whichismorethananormalrewillgenerate.Suchmaterialsas
pitch/waxladenlogs,verydrymillendlumberandlargeamounts
ofpaperorcardboardboxescancreateanexcessivelyhotreand
should not be burned in this fireplace. Always keep the fire well back
fromthedoorsandneverallowamestocontacttheglass.
WARNING: Fireplaces equipped with glass doors
should be operated only with doors fully opened or
doorsfully closed. Doors,if left partly open,may draw
gasandameoutofthereplaceopeningcreating
risks of both fire and smoke.
WARNING: Discontinue use of the appliance imme-
diately if doors are damaged and contact a qualified
installer for repair. Only doors certified with the ap-
pliance shall be used.
WARNING: Do not slam or strike doors. Damage
can result in a hazardous condition.
Cleaning Glass
Clean the glass with any commercial glass cleaner or soap and
water. Do not use any abrasive material to clean the glass. Do not
clean the glass with any cool water is the glass is still hot from the
fire and smoke.
A gas line or gas log lighter may be installed for the purpose of
installing a vented or vent-free decorative gas appliance incorporat-
inganautomaticshutoffdeviceandcomplyingwiththeStandard
forDecorativeGasAppliancesforInstallationinVentedFireplaces,
ANSIZ21.60orAmericanGasAssociationdraftrequirementsfor
GasFiredLogLightersforWood Burning Fireplaces, Draft NO. 4
dated August, 1993.
Ifyouwishtoinstallanunvented(vent-free)gaslogset,onlyunvented
gas log sets which have been found to comply with the standard for
unventedroom heaters, ANSI Z21.11.2 aretobe installed in this
fireplace.
OUTSIDE AIR AND DAMPER HANDLE OPERATION
The damper handle, which opens and closes the damper blade, is
located in the upper front face of the fireplace. Pushing the handle into
the left of the keyway slot will free the damper blade to automatically
open. Pushing the handle in to the right will lock the damper blade
closed(seeFigure22).
The outside air kit handle is located at the left hand side of the fireplace
(seeFigure22).Pullingthehandleoutwillfreetheoutsideairdoor
to open. Pushing the handle in will lock the door closed.
Figure 22 - Damper and Air Kit Handle
OPEN CLOSE
Handle
Outside Air
Kit Handle
Keyway
Slot
Handle
Retainer
WARNING: Risk of fire! Replace grate with IHP
model111028-01only.Thisgratehasbeendesignedto
keep the operation of your fireplace safe and efficient.

Astria.US.com 126764-01D14
OPERATION AND MAINTENANCE GUIDELINES
Continued
LOCATING ACCESS COVER PLATE
Sheetmetalcoverplateslocatedunderneathfronthearthrefractorymay
have shifted or moved out of place while fireplace was in transit. These
cover plates must be kept in the proper location prior to using the fireplace
(SeeFigure23).
For further operating guidelines, instructions and warranty infor-
mation, please refer to your homeowner's guide or contact your
authorized dealer.
Figure 23 - Locating Access Cover Plate
Access
Panel
REPLACEMENT PARTS
SeePages15to17foracompletereplacementpartslist.Useonly
parts supplied from the manufacturer.
Normally,allpartsshouldbeorderedthroughyourIHPdistributor
or dealer. Parts will be shipped at prevailing prices at time of order.
When ordering repair parts, always give the following information:
1. The model number of the fireplace.
2. The serial number of the fireplace.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the fireplace.
Ifyouencounteranyproblemsorhaveanyquestionsconcerningthe
installation or application of this fireplace, please contact your dealer.
IHP
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
Visit us at Astria.US.com
TECHNICAL SERVICE
You may have further questions about installation, operation, or
troubleshooting.PleasecontactyourIHPdealerforanyquestions
or concerns. When contacting your dealer please have your model
and serial numbers of your fireplace ready. You can also visit our
websiteatAstria.US.com

Astria.US.com
126764-01D 15
Rear
Left Side Front Bottom
Bottom
Right Side
KEY
NO. CATALOG NO. DESCRIPTION Tuscan36p2 Tuscan36p3 QTY.
9 J3955 LeftRefractory,NaturalWhiteStackedBrick • 1
J4128 LeftRefractory,NaturalWhiteHerringboneBrick • 1
10 J3960 RightRefractory,NaturalWhiteStackedBrick • 1
J4131 RightRefractory,NaturalWhiteHerringbone • 1
11 J3965 RearRefractory,NaturalWhiteStackedBrick • 1
J4134 RearRefractory,NaturalWhiteHerringbone • 1
12 J4472 BottomRearRefractory,NaturalWhiteBrick • • 1
13 J4474 BottomFrontRefractory,NaturalWhiteBrick • • 1
REFRACTORYBRICK
PARTS
WOOD BURNING FIREPLACE MODELS TUSCAN36P2 AND TUSCAN36P3
MODEL NO. CATALOG NO.
Tuscan36P2 F0540
Tuscan36P3 F0541
WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved
by IHP. Use of non-approved parts can result in poor performance and safety hazards.

Astria.US.com 126764-01D16
PARTS
WOOD BURNING FIREPLACE MODELS TUSCAN36P2 AND TUSCAN36P3
9
24
16
31 25
16
4 30
32
19
12
23
20
28
17
8
1
5
21
2
18
11
14
3
13
22
10 6
29
7
33/34
26
27
15
MODEL NO. CATALOG NO.
Tuscan36P2 F0540
Tuscan36P3 F0541

Astria.US.com
126764-01D 17
PARTS
WOOD BURNING FIREPLACE MODELS TUSCAN36P2 AND TUSCAN36P3
This list contains replaceable parts used in your fireplace. When ordering parts, see ReplacementParts on page 14 of this manual.
KEY
NO. CATALOG NO. DESCRIPTION QTY.
1** InsulationPan 1
2 ** Fireplace Top 1
3 ** FireplaceSurround 1
4 J3946 AirRodRetainer 1
5 J3947 DamperRodRetainer 1
6 ** FireboxBottom 1
7 ** FireboxSurround 1
8 ** AirSeparator 1
9Seepage15 Left,RefractoryBrickLiner 1
10 Seepage15 Right,RefractoryBrickLiner 1
11 Seepage15 Rear,RefractoryBrickLiner 1
12 Seepage15 BottomRearRefractory,BrickLiner 1
13 Seepage15 BottomFrontRefractory,BrickLiner 1
14 J3972 FireboxSupportLeg 4
15 ** DamperCanCollar 1
16 J8012 ScreenAssemblykit 1
17 ** FireboxTopAssembly 1
18 J3980 Air Kit Door Assembly 1
19 ** Face Weldment 1
20 J4470 AirDeector 1
21 ** FireplaceTopInsulation 1
22 J4052 Access Panel 1
23 J4491 Grate 1
24 ** CollarInsulation 1
25 J6893 ChimneyStarterCollar 1
26 J6895 RefractoryRetainer 2
27 J3939 GrateRetainer 2
28 J4504 DoorStop 1
29 J4523 PivotClip 2
30 J6905 SpringClip 2
31 J6918 TopSpacer 4
32 J6934 ConduitPlateCover 4
33 J6951 GasConduit 2
34 J6952 GasConduit 2
PARTS AVAILABLE NOT SHOWN
106625-01 HomeOwner’sGuide 1
J6906 EmberProtector 2
**Notaeldreplaceablepart
WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved
by IHP. Use of non-approved parts can result in poor performance and safety hazards.

Astria.US.com 126764-01D18
ACCESSORIES
BI-FOLD GLASS DOORS
CAT NO. MODEL DESCRIPTION
F0987 BDO36 36"OutdoorBi-FoldGlassDoor-Blacknish
F0988 BDO36B 36"OutdoorBi-FoldGlassDoor-BrushedBrassnish
F0989 BDO36P 36"OutdoorBi-FoldGlassDoor-Platinumnish
DOUBLE WALL PIPE
F0895 12-8DM 12"SectionDoubleWallPipeSnapLock
F0896 18-8DM 18"SectionDoubleWallPipeSnapLock
F0897 24-8DM 24"SectionDoubleWallPipeSnapLock
F0898 36-8DM 36"SectionDoubleWallPipeSnapLock
F0899 48-8DM 48"SectionDoubleWallPipeSnapLock
F0881 12-8HT 12"SectionHi-TempDoubleWallPipeSnapLock
F0882 18-8HT 18"SectionHi-TempDoubleWallPipeSnapLock
F0883 24-8HT 24"SectionHi-TempDoubleWallPipeSnapLock
F0884 36-8HT 36"SectionHi-TempDoubleWallPipeSnapLock
F0885 48-8HT 48"SectionHi-TempDoubleWallPipeSnapLock
30° OFFSET AND RETURN
F0900 30E-8DM 30DegreeOffsetandReturn
OPTIONAL OUTSIDE AIR KIT FOR FLOOR INSTALLATION
F1091 AK4 CompleteOutsideAirKitw/CollarsHood&3'Flex
OPTIONAL OUTSIDE AIR KIT FOR SIDEWALL INSTALLATION
F1093 AK4F OutsideAirKitCollar,Hood&3'FlexforFloorVenting
STORM COLLAR
F0915 SC1-1 StormCollar
FIRESTOP SPACER
F0907 3600FS-8DM-1 1"ClearanceFirestopSpacer
ROOF FLASHING
F0909 V6F-8DM RoofFlashing0to6/12Pitch(30"Base)
F0910 V12F-8DM RoofFlashing6/12to12/12Pitch

Astria.US.com
126764-01D 19
ANTI-DRAFT SHIELD
(Round Top Termination Only)
F0927 ADS-8DM Anti-DraftShieldforRoundTopOnly
MESH ROUND TOP TERMINATIONS
F0916 RT-8DM RoundTopwithMeshScreen
F0888 RT-8HT Hi-TempRoundTopwithMeshScreen
MESH ROUND TOP TERMINATIONS WITH SLIP SECTION
F0917 RTT-8DM RoundTopwithSlipSection&Mesh
F0889 RTT-8HT Hi-TempRoundTopw/MeshScreenandSlipSection
ROUND TOP TERMINATIONS WITH LOUVERS
F0918 RLT-8DM RoundTopwithLouveredScreen
F0890 RLT-8HT Hi-TempRoundTopwithLouveredScreen
ROUND TOP TERMINATIONS WITH LOUVERS W/SLIP SECTION
F0919 RLTT-8DM RoundTopwithSlipSection&Louvers
F0891 RLTT-8HT Hi-TempRoundTopw/Lvrd.ScreenandSlipSection
SQUARE TOP TERMINATION WITH LOUVERS
F0920 ET-8DM SquareTop
F0892 ET-8HT Hi-TempPyramidTopwithSlipSection
SQUARE TOP TERMINATION WITH LOUVERS AND SLIP SECTION
F0921 ETL-8DM SquareTopwithSlipSection
F0893 ETL-8HT Hi-TempLargePyramidTopwithSlipSection
MESH SQUARE TOP TERMINATION
F0922 ETO-8DM SquareTopwithMesh
MESH SQUARE TOP TERMINATION WITH SLIP SECTION
F0923 ETLO-8DM SquareTopwithMeshandSlipSection
STAINLESS STEEL HOOD
Requiredwheninstallingavent-freegasloginthisreplace.
F1052 HS36 36"StainlessSteelHoodw/4"Brow
DRAIN PAN
F1089 DP36 Drain Pan
FIRESTOP THIMBLE
F0911 38FST FirestopThimble(Usewhenpenetratingajoist)
F0912 FST30 FirestopThimble(Usewhenoffsettingthroughajoist)
LABEL-UL127-50PK WARNING
HOT
• Fire Risk
• Insulation and combustibles must not touch
pipe
• Consult manual for clearance requirements
• Ensure proper connection
WARNING
HOT
• Fire Risk
• Insulation and combustibles must not touch
pipe
• Consult manual for clearance requirements
• Ensure proper connection
WARNING
HOT
• Fire Risk
• Insulation and combustibles must not touch
pipe
• Consult manual for clearance requirements
• Ensure proper connection
900599-01
F2659 LABEL-UL127-
50PK UL127VentingLabel-50PK
ACCESSORIES Continued

IMPORTANT NOTICE
A manufactured shroud which
has been approved by a na-
tional testing agency for use
with this fireplace may be used
if installed in accordance with
the instructions by its manu-
facturer. A locally fabricated
shroud may be used with IHP
Shroud Leg Spacer Kit (SLK)
in accordance with instructions
provided with the shroud.
CanadiancodeCAN/ULC-S610-M87andotherpertinent
codes require stainless steel chimney for the installation
ofthisreplace.AColdAirClimateKitisalsorequired
inCanadaandisrecommendedforcoolerregionsinthe
UnitedStates.Below,nd alistof approved stainless
steel parts.
Chimney Parts List for Canada
Catalog
No. Model No. 8" Hi-Temp Wood burning Chimney
F0881 12-8HT 12"SectionHi-TempDouble
WallPipeSnapLock
F0882 18-8HT 18"SectionHi-TempDouble
WallPipeSnapLock
F0883 24-8HT 24"SectionHi-TempDouble
WallPipeSnapLock
F0884 36-8HT 36"SectionHi-TempDouble
WallPipeSnapLock
F0885 48-8HT 48"SectionHi-TempDouble
WallPipeSnapLock
F0886 30E-8HT 30DegreeHi-TempOffset
andReturn
F0887 12S-8HT Hi-TempChimneySupport
(ForUseWithChimney
HeightsInExcessof30')
F0888 RT-8HT Hi-TempRoundTopwith
MeshScreen
F0889 RTT-8HT Hi-TempRoundTopwith
MeshScreenandSlipSec-
tion
F0890 RLT-8HT Hi-TempRoundTopwith
LouveredScreen
F0891 RLTT-8HT Hi-TempRoundTopwith
LouveredScreenandSlip
Section
F0892 ET-8HT Hi-TempPyramidTopwith
SlipSection
F0893 ETL-8HT Hi-TempLargePyramidTop
withSlipSection(usewithall
8"systems)
F0894 AP-8HT Hi-TempAnchorPlate/Col-
larAssembly(formasonry
replaces)
F0929 CAK-8 ColdAirCollarKit-8"
Chimney
*When ordered alone, this part cannot ship via parcel
delivery services.
NOTICE: The firebox canopy (hood)
must not be modified or replaced with
a canopy that may be provided with
the unvented decorative room heater.
CAUTION: THE STRUCTURAL INTEG-
RITY OF THE MANUFACTURED HOME
FLOOR, WALL, AND CEILING/ROOF
MUST BE MAINTAINED.
WARNING: DO NOT INSTALL
IN SLEEPING ROOM OF MOBILE
HOMES.