ASTUTE LIGHTING SL6015D-MCT User manual

2.4G RF
2.4G Wireless Remote Control Manual
(ONLY COMPATIBLE WITH SL6015D-MCT)
REMOTE CONTROL FUNCTIONS:
M1 M2
SPECIFICATION:
PCB Board No.
Transmission Frequency
Standby Consumption
Working Voltage
Control Distance
Modulation
Transmission Power
Battery
V1.0
2400-2483.5MHz
3uA
12mA
20-30 Metres
GFSK
10dB
Button Battery
TURN ON/OFF
INCREASE/DECREASE
CCT
SYNC/FUNCTION
BUTTON
COOL WHITE/6000K
NATURAL WHITE/4000K PRESET DIM FUNCTION
WARM WHITE/2700K
MEMORY FUNCTION 1
Slow Click Once -
Memorises Current Setting
Quick Click Once -
Saved Setting Switches On
Pressing UP Will Increase
Pressing DOWN Will Decrease
MEMORY FUNCTION 2
Slow Click Once -
Memorises Current Setting
Quick Click Once -
Saved Setting Switches On
Adjust Brightness
FLASHING INDICATOR

2.4G RF
STEP 1: SWITCH THE LAMP ON FROM THE WALL SWITCH & SIMULTANEOUSLY CLICK THE SYNC/FUNCTION
BUTTON ( ) 5 TIMES WITHIN A 5 SECOND PERIOD.
STEP 2: IF STEP 1 IS FOLLOWED CORRECTLY, THE LAMP WILL SLOW FLASH 6 TIMES TO CONFIRM
CLEARING/DE-SYNCING
STEP 1: SWITCH THE LAMP ON FROM THE WALL SWITCH & SIMULTANEOUSLY PRESS DOWN THE SYNC/
FUNCTION BUTTON ( ) WITHIN 5 SECONDS OF SWITCHING THE LAMP ON FROM THE WALL SWITCH.
STEP 2: IF STEP 1 IS FOLLOWED CORRECTLY, THE LAMP WILL SLOW FLASH 3 TIMES TO CONFIRM SYNC IS
COMPLETE
PLEASE NOTE: THIS PROCESS CAN TAKE A FEW ATTEMPTS, AS IT HAS TO BE DONE SIMULTANEOUSLY
BATTERY :
M1 M2
GROUPING MULTIPLE LAMP FITTINGS:
LED
LAMP 1
LED
LAMP 2
LED
LAMP 3
LED
LAMP 4
LED
LAMP N
ONE REMOTE CAN CONTROL UPTO 20 FITTINGS
1. Make sure all fittings are switched off.
2. Sync each fitting individually to the remote you wish
3. Switch off the first synced lamp in order to sync the second lamp
4. sync upto 20 fittings on one remote
PLEASE NOTE: SYNCING WILL NOT WORK IF MULTIPLE FITTINGS ARE ON AT THE SAME TIME,
ALL FITTINGS MUST BE SYNCED INDIVIDUALLY - EVEN IF SYNCING TO THE SAME REMOTE
PLEAE ENSURE THE BATTERY IS PLACED CORRECTLY WITHIN THE REMOTE CONTROL. UPON PLACING THE
BATTERY, PRESS ANY BUTTON & VEIW THE INDICATOR TO CONFIRM REMOTE IS WORKING
PLEASE NOTE: UPON FIRST USE, THE FITTING & THE REMOTE SHOULD ALREADY BE IN SYNC.
HOW TO MATCH/SYNC THE LIGHT FITTING WITH THE REMOTE:
CODE MATCH/SYNC:
CODE CLEARING/DE-SYNC:
PLEASE NOTE: THIS PROCESS CAN TAKE A FEW ATTEMPTS, AS IT HAS TO BE DONE SIMULTANEOUSLY
ONE REMOTE CAN CONTROL UP TO 20 LIGHT FITTINGS AT THE SAME TIME. IF YOU WISH TO HAVE MULTIPLE
LIGHT FITTINGS ON ONE REMOTE PLEASE FOLLOW THE INSTRUCTIONS BELOW. EACH LAMP WOULD HAVE TO
BE PROGRAMMED SEPERATELY
STEP 1: SWITCH OFF ALL FITTINGS FROM THE WALL SWITCH
STEP 2: SWITCH ON 1st FITTING TO BE SYNCED & FOLLOW CODE MATCH/SYNC INSTRUCTIONS (ABOVE)
STEP 3: ONCE THE FITTING SLOW FLASHES 3 TIMES, SWITCH IT OFF FROM THE WALL SWITCH.
STEP 4: ALL FITTINGS MUST BE SYNCED INDIVIDUALLY.
STEP 5: REPEAT STEP 1, 2 & 3 UNTIL ALL FITTINGS ARE SYNCED
FOR MORE INFORMATION, PLEASE CALL US ON 01254 695914