AT&T CL81101 User manual

Telephone base installation
If you have DSL
high-speed Internet
service, a DSL filter
(not included) is
required.
This quick start guide provides you with basic instructions only.
For more complete instructions, refer to your Abridged user’s
manual provided in the package, or see the online Complete
user’s manual at www.telephones.att.com/manuals.
Plug the power adapter
into an electrical outlet
not controlled by
a wall switch.
Charger installation
Battery installation
Install the battery as shown below. Charge your handset(s) before initial use.
The battery is fully charged after 10 hours of continuous charging.
Quick start guide
CL81101/CL81201/CL81211/CL81301
Plug the telephone
base power adapter
into an electrical
outlet not controlled
by a wall switch..
Route the
cords through
the slots.
Plug the other end
of the telephone
line cord into a
telephone jack or
a DSL filter.
3. Charge the handset by
placing it face forward
in the telephone base
or charger.
Use only the supplied rechargeable battery or replacement battery (model BT166342).
Raise the
antenna.
1
Caution: Use only the power adapter provided with this product. To obtain a replacement, visit
our website at www.telephones.att.com or call 1 [phone].
In Canada, dial 1 [phone].
qCID/VOLUME
Show caller ID history.
Scroll down in menus.
Move cursor to the left when
entering names or numbers.
Decrease listening volume
when on a call.
•
•
•
•
MUTE/DELETE
Mute the microphone during a
call.
Delete the displayed entry while
in the directory, call log or redial
list.
While predialing, press to delete
digits.
•
•
•
PHONE/FLASH
Make or answer a call.
Answer a call waiting call during
a call.
•
•
/SPEAKERSPEAKER
Switch between the speakerphone
and handset.
pDIR/VOLUME
Show directory entries.
Scroll up in menus.
Move cursor to the right when
entering names or numbers.
Increase listening volume when
on a call.
•
•
•
•
MENU/SELECT
Show the menu.
Select an item or save an entry
or setting while in the menu.
•
•
OFF/CANCEL
Hang up a call.
Press to cancel an operation,
back up to the previous
menu, or exit the menu display,
or press and hold to return to
idle mode.
Press and hold in idle mode to
erase missed call indicator.
•
•
•
REDIAL/PAUSE
Press repeatedly to view the last
10 numbers dialed.
Press and hold to insert a dialing
pause while entering numbers.
•
•
1
Press repeatedly to add or
remove 1 in front of the call log
entry before dialing or saving it to
the directory.
Press and hold to set or dial your
voicemail number.
•
•
# (pound key)
Press repeatedly to display other
dialing options when reviewing a
caller ID log entry.
EQ
Change the audio quality to best
suit your hearing.
Quick reference guide
TONE
Press to switch to tone dialing
temporarily during a call if you have
pulse service.
Handset
side view
Push to talk
Press to initiate a one-to-one or
one-to-group broadcast.
Press and hold to broadcast to a
group of handsets.
•
•
Initial settings
We recommend you program your telephone system before use.
The following are a few examples of common features to set before using
the telephone. Refer to the Handset settings in the Abridged user’s manual
or the online Complete user’s manual for detailed instructions on setting all
telephone features.
Set date/time
Set the date/time before using the telephone.
1. MENU -> qor p-> Set date/time -> SELECT.
2. Enter the month, day and year using the dialing keys -> SELECT.
3. Enter the hour and minute using the dialing keys.
4. qor pto choose AM or PM -> SELECT.
Handset ringer volume
You can set the ringer volume level to one of the six levels or turn the
ringer off.
1. MENU -> qor p-> Ringers -> SELECT.
2. SELECT to select Ringer volume.
3. qor pto choose the desired level -> SELECT.
Language
If you want to change the display language, or you have accidentally changed
the language and want to switch it back to English, follow the steps below.
MENU -> On the handset, enter 364# using the dialing keys.•
23
1. Plug the battery
connector securely
into the socket inside
the handset battery
compartment. Insert
the supplied battery
with the label THIS
SIDE UP facing up as
indicated.
2. Align the cover flat
against the battery
compartment, then
slide it upwards
until it clicks into
place.
Handset
Telephone
base
IN USE indicator
On when the handset is in use.
On when a handset is being registered.
Flashes when there is an incoming call
or when handsets are being deregistered.
Flashes when another telephone is in
use on the same line.
HANDSET LOCATOR
While the telephone is idle, press
to page all handsets.
Press and hold to begin handset
deregistration.
•
•
Telephone operation
Operation Steps
Making a call Press PHONE or /SPEAKERSPEAKER -> Enter the telephone
number.
On-hook dialing
(predialing)
Enter the telephone number -> Press PHONE or
/SPEAKERSPEAKER to call.
Answering a call Press PHONE or /SPEAKERSPEAKER, or press any dialing key
(0-9,TONE or #).
Ending a call Press OFF or return the handset to the telephone base
or charger.
Speakerphone During a call, press /SPEAKERSPEAKER to switch between
handsfree speakerphone and normal handset use.
Redial Press REDIAL repeatedly to select the desired entry
-> PHONE or /SPEAKERSPEAKER to call.
Volume control Press VOLUMEqto decrease or press VOLUMEpto
increase the listening volume during a call.
Call waiting
(Requires subscription
from telephone
service provider)
Press FLASH to put current call on hold and to take the
new call; press again to switch back and forth between
calls.
BY1021
BT183342/BT283342
Plug the power cord and telephone
line cord into the jacks.

For more detailed instructions, please refer to the Abridged user’s manual
provided in your package, or for a full set of installation and operation
instructions, refer to the online CL81101/CL81201/CL81211/CL81301 DECT
6.0 cordless telephone with caller ID/call waiting Complete user’s manual at
www.telephones.att.com/manuals.
For customer service or product information, visit our website at
www.telephones.att.com or call 1 [phone]. In Canada, dial
1 [phone].
© 2010-2011 Advanced American Telephones. All Rights Reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219.
Printed in China. Issue 4 AT&T 12/11.
Caller ID
This product supports caller ID services offered by most telephone service providers.
The telephone stores caller ID information for the last 50 incoming calls in the
telephone base. This information is common to all handsets.
Missed call indicator
When a handset is in idle mode and has new or missed calls, its screen shows
XX Missed calls.
You can erase the missed call indicator either by reviewing the call log one by
one, or by pressing and holding CANCEL on the handset in idle mode.
Review and dial a number in the call log
1. CID in idle mode -> qor pto scroll through the list.
2. PHONE or /SPEAKER to call when the desired entry is displayed.
Directory
The directory can store up to 50 entries, which are shared by all system handsets.
Operation Steps
Adding an entry 1. MENU.
2. qor p-> Directory -> SELECT.
3. qor p-> Add contact -> SELECT.
4. Enter a telephone number up to 30 digits -> SELECT.
5. Enter a name up to 15 characters -> SELECT.
Searching/dialing
an entry
1. DIR in idle mode.
2. Press qor pto browse through the directory, or press
the dialing keys (0-9) to start a name search.
3. Press PHONE or /SPEAKER to call.