AT&T TL91270 User manual

User’s manual
TL91270
DECT 6.0 cordless
telephone with BLUETOOTHBLUETOOTH®
wireless technology
6
Getting started
If you subscribe to high-speed Internet service (digital subscriber line - DSL)
through your telephone line, you must install a DSL filter between the
telephone line cord and the telephone wall jack. The filter prevents noise and
caller ID problems caused by DSL interference. Please contact your DSL service
provider for more information about DSL filters.
Follow the steps below to install the telephone.
NOTE: The telephone base comes without the wall-mount bracket for tabletop use. If you
want to mount your telephone on a wall, refer to Wall-mount installation on
pages 10-11 for details.
Telephone base installation
Plug one end of
the telephone
line cord into the
telephone jack on
the bottom of the
telephone base.
1.
DSL filter (not included) is
required if you have DSL
high-speed Internet service.
Telephone line cord
Route the cords
through the slots.
3.
Plug the small
end of the larger
power adapter
into the power
jack on the
bottom of the
telephone base.
2.
Plug the large end
of the larger power
adapter into an
electrical outlet not
controlled by a wall
switch.
5.
Plug the other end
of the telephone
line cord into a
telephone wall jack.
6.
Raise the antenna.4.

7
Getting started
IMPORTANT INFORMATION:
Use only the power adapter(s) provided with this product. To obtain a replacement, visit our
website at www.telephones.att.com or call 1 [phone]. In
Canada, dial 1 [phone].
The power adapters are intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling,
under-the-table or cabinet outlet.
1.
2.
Charger installation
Plug the power adapter into an electrical outlet not
controlled by a wall switch.
8
Getting started
Battery installation & charging
Battery charging
Install the battery as shown on the next page. Once you have installed the
battery, the screen indicates the battery status (see table below). If necessary,
place the handset in the telephone base or charger to charge the battery.
For best performance, keep the handset in the charger when not in use. The
battery is fully charged after 16 hours of continuous charging. See the table
on page 93 for battery operating times.
If the screen is blank, you need to charge the handset without interruption
for at least 10 minutes to give the handset enough charge to use the
telephone for a short time. The screen shows Low battery and the backlight
is off until you have charged the battery without interruption for at least
one hour. The following table summarizes the battery charge indicators and
actions to take.
Battery indicators Battery status Action
The screen is blank. Battery has no charge and the
handset cannot be used.
Charge without interruption
until the screen shows Low
battery (at least 10 minutes).
The screen show No battery. Battery is not installed
probably, but the handset is
placed on the telephone base
or charger
See the Battery installation
section on page 9 for battery
installation.
The screen shows Place in
charger and flashes
Battery has very little charge
and the handset cannot be
used.
Charge without interruption
until the screen shows
Low battery (at least four
minutes).
The screen shows Low
battery and flashes.
Battery has enough charge to
be used for a short time.
Charge without interruption
until the screen shows
HANDSET X (at least one
hour).
The screen shows HANDSET X
and the battery icon shows
, or .
Battery is charged. To keep the battery charged,
place it in the telephone
base or charger when not
in use.
NOTE: If you are on a call in low battery mode, you hear four short beeps every minute.

9
Getting started
Battery installation & charging
Battery installation
Install the battery as shown below.
Plug the battery
connector securely
into the socket inside
the handset battery
compartment, matching
the color-coded label.
Insert the supplied
battery with the label
THIS SIDE UP facing
up as indicated.
1.
To replace the battery, press the tab and slide
the battery compartment cover downwards. Lift
out the old battery and disconnect it from the
handset. Follow the instructions above to install
and charge the new battery.
Align the cover flat
against the battery
compartment, then
slide it upwards until
it clicks into place.
2. Charge the handset by
placing it face up in
the telephone base or
charger. The CHARGE
light is on when
charging.
3.
IMPORTANT INFORMATION:
Use only the supplied rechargeable battery or replacement battery (model BT166342). To order,
visit our website at www.telephones.att.com, or call 1 [phone].
In Canada, dial 1 [phone].
CHARGE light
10
Getting started
Wall-mount installation
Your telephone base is ready for tabletop use. If you want to mount yourIf you want to mount your
telephone on a wall, use the provided wall bracket to connect with a
standard dual-stud telephone wall-mounting plate. If you do not have this
mounting plate, you can purchase one from many hardware or consumer
electronics retailers. You may need a professional to install the mounting
plate.
Tabletop to wall-mount installation
1. Position the telephone base as shown below. Insert the extended tabs
(marked B) of the wall-mount bracket into the slots on the back of the
telephone base (marked B). Push the telephone base down until it is securely
in place.
2. If you are using a DSL filter, plug the line cord into the filter now. Route
the telephone line cord (or DSL filter) through the wall mount bracket hole.
Route the power cord out of the bottom of the telephone.
3. Plug the telephone line cord (or DSL filter) into the wall jack. Plug the
power adapter into a power outlet not controlled by a wall switch.
4. Align the holes on the bracket with the standard wall plate and slide the
bracket down until it locks securely. Bundle the telephone line cord and
power adapter cord neatly with a twist tie.

11
Getting started
Wall-mount installation
Wall-mount to tabletop installation
To change the telephone base from the wall-mount position to tabletop
position, follow the steps below.
1. Remove the wall-mount bracket from the wall. If the telephone line cord
and power adapter cord are bundled, untie them first.
2. Lift the telephone base up to detach it from the plastic wall-mount
bracket. Unplug the telephone line cord (or DSL filter) from the wall. Unplug
the power adapter from the power outlet.
3. See Telephone base installation on page 6.
88
Appendix
Important safety information
This symbol is to alert you to important operating or servicing instructions that may appear
in this user’s manual. Always follow basic safety precautions when using this product to reduce
the risk of injury, fire, or electric shock.
Safety information
Read and understand all instructions in the user’s manual. Observe all markings on the
product.
Avoid using a telephone during a thunderstorm. There might be a slight chance of electric
shock from lightning.
Do not use a telephone in the vicinity of a gas leak. If you suspect a gas leak, report it
immediately, but use a telephone away from the area where gas is leaking. If this product is a
cordless model, make sure the base is also away from the area.
Do not use this product near water, or when you are wet. For example, do not use it in a
wet basement or shower, or next to a swimming pool, bathtub, kitchen sink, or laundry tub.
Do not use liquids or aerosol sprays for cleaning. If the product comes in contact with any
liquids, unplug any line or power cord immediately. Do not plug the product back in until it
has dried thoroughly.
Install this product in a protected location where no one can trip over any line or power
cords. Protect cords from damage or abrasion.
If this product does not operate normally, read Troubleshooting section on pages 75-86
of this user’s manual. If you cannot solve the problem, or if the product is damaged, refer
to Limited warranty section on pages 92-93. Do not open this product except as may be
directed in your user’s manual. Opening the product or reassembling it incorrectly may
expose you to hazardous voltages or other risks.
Replace batteries only as described in your user’s manual (pages 8-9). Do not burn or
puncture batteries — they contain caustic chemicals.
This power adapter is intended to be correctly oriented in a vertical or floor mount position.
The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an
under-thetable/cabinet outlet.
CAUTION: Use only the power adapter provided with this product. To obtain a replacement,
visit our website at www.telephones.att.com, or call 1 (800) 222–3111.
In Canada, dial 1 [phone].
Especially about corded telephones
Privacy: The same features that make a cordless telephone convenient create some
limitations. Telephone calls are transmitted between the telephone base and the handset
by radio waves, so there is a possibility that your cordless telephone conversations could
be intercepted by radio receiving equipment within range of the cordless handset. For this
reason, you should not think of cordless telephone conversations as being as private as those
on corded telephones.
Electrical power: The telephone base of this cordless telephone must be connected to a
working electrical outlet which is not controlled by a wall switch. Calls cannot be made from
the handset if the telephone base is unplugged, switched off or if the electrical power is
interrupted.
•
•
•
•
•
•
•
•
•
•

89
Appendix
Important safety information
Potential TV interference: Some cordless telephones operate at frequencies that may cause
interference to TVs and VCRs. To minimize or prevent such interference, do not place the
telephone base of the cordless telephone near or on top of a TV or VCR. If interference
is experienced, moving the cordless telephone farther away from the TV or VCR will often
reduce or eliminate the interference.
Rechargeable batteries: This product contains nickel-metal hydride rechargeable batteries.
Exercise care in handling batteries in order not to create a short circuit with conductive
material such as rings, bracelets, and keys. The battery or conductor may overheat and cause
harm. Observe proper polarity between the battery and the battery charger.
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do
not burn or puncture. Like other batteries of this type, if burned or punctured, they could
release caustic material which could cause injury.
The RBRC™ Seal means that the manufacturer is voluntarily participating in
an industry program to collect and recycle nickel-metal hydride rechargeable
batteries when taken out of service within the United States. These batteries
may be taken to a participating local retailer of replacement batteries or
recycling center. Or you may call 1 (800) 8-BATTERY for locations accepting
spent Ni-MH batteries.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research,
LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference
between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S.
Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
Should keep wireless telephones at least six inches from the pacemaker.
Should NOT place wireless telephones directly over the pacemaker, such as in a breast
pocket, when it is turned ON.
Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons
using wireless telephones.
SAVE THESE INSTRUCTIONS
•
•
•
•
•
•
90
Appendix
FCC part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted
by the Administrative Council for Terminal Attachments (ACTA). The label on the back or
bottom of this equipment contains, among other things, a product identifier in the format US:
AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network
must comply with the applicable Part 68 rules and technical requirements adopted by ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be
used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions
in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect
to your telephone line and still have them ring when you are called. The REN for this product is
encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is
03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For
more information, please contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing
equipment connected to your telephone line, ensure the connection of this equipment does
not disable your alarm equipment. If you have questions about what will disable the alarm
equipment, consult your telephone company or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the
problem has been corrected. Repairs to this telephone equipment can only be made by the
manufacturer or its authorized agents. For repair procedures, follow the instructions outlined
under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone company may
temporarily discontinue your telephone service. The telephone company is required to notify
you before interrupting service. If advance notice is not practical, you will be notified as soon as
possible. You will be given the opportunity to correct the problem and the telephone company
is required to inform you of your right to file a complaint with the FCC. Your telephone company
may make changes in its facilities, equipment, operation, or procedures that could affect the
proper functioning of this product. The telephone company is required to notify you if such
changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone
numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers,
please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry
Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication
of the maximum number of devices allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
•
•

91
Appendix
FCC part 15
This equipment has been tested and found to comply with the requirements for a Class B digital
device under Part 15 of the Federal Communications Commission (FCC) rules.
These requirements are intended to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. Privacy of
communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency
energy that can be safely absorbed by a user or bystander according to the intended usage
of the product. This product has been tested and found to comply with the FCC criteria. The
handset may be safely held against the ear of the user. The telephone base shall be installed
and used such that parts of the user’s body other than the hands are maintained at a distance of
approximately 20cm (8 inches) or more.
This Class B digital apparatus complies with Canadian ICES-003.
•
•
•
•
92
Appendix
Limited warranty
The AT&T brand is used under license - any repair, replacement or warranty service, and all
questions about this product should be directed to: In the United States of America, call
1 [phone] or visit www.telephones.att.com; In Canada, call
1 [phone].
What does this limited warranty cover?
The manufacturer of this AT&T-branded product warrants to the holder of a valid proof of
purchase (“CONSUMER” or “you”) that the product and all accessories provided in the sales
package (“PRODUCT”) are free from defects in material and workmanship, pursuant to the
following terms and conditions, when installed and used normally and in accordance with the
PRODUCT operating instructions. This limited warranty extends only to the CONSUMER for
products purchased and used in the United States of America and Canada.
What will be done if the PRODUCT is not free from defects in materials and workmanship
during the limited warranty period (“materially defective PRODUCT”)?
During the limited warranty period, the manufacturer’s authorized service representative
repairs or replaces at the manufacturer’s option, without charge, a materially defective
PRODUCT. If the manufacturer repairs the PRODUCT, they may use new or refurbished
replacement parts. If the manufacturer chooses to replace the PRODUCT, they may replace
it with a new or refurbished PRODUCT of the same or similar design. The manufacturer
retains the defective parts, modules, or equipment. Repair or replacement of the PRODUCT,
at the manufacturer’s option, is your exclusive remedy. The manufacturer returns the repaired
or replacement products to you in working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the PRODUCT extends for ONE (1) YEAR from the date of
purchase. If the manufacturer repairs or replaces a materially defective PRODUCT under the
terms of this limited warranty, this limited warranty also applies to repaired or replacement
PRODUCT for a period of either (a) 90 days from the date the repaired or replacement
PRODUCT is shipped to you or (b) the time remaining on the original one-year limited
warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
PRODUCT that has been subjected to misuse, accident, shipping or other physical damage,
improper installation, abnormal operation or handling, neglect, inundation, fire, water, or
other liquid intrusion; or
PRODUCT that has been damaged due to repair, alteration, or modification by anyone
other than an authorized service representative of the manufacturer; or
PRODUCT to the extent that the problem experienced is caused by signal conditions,
network reliability or cable or antenna systems; or
PRODUCT to the extent that the problem is caused by use with non-AT&T accessories; or
PRODUCT whose warranty/quality stickers, PRODUCT serial number plates or electronic
serial numbers have been removed, altered or rendered illegible; or
PRODUCT purchased, used, serviced, or shipped for repair from outside the United States
of America or Canada, or used for commercial or institutional purposes (including but not
limited to products used for rental purposes); or
PRODUCT returned without valid proof of purchase (see item 6 below); or
Charges for installation or setup, adjustment of customer controls, and installation or
repair of systems outside the unit.
1.
2.
3.
4.
•
•
•
•
•
•
•
•

93
Appendix
How do you get warranty service?
To obtain warranty service in the United States of America, visit
www.telephones.att.com or call 1 [phone]; in Canada, please
dial 1 [phone]. NOTE: Before calling for service, please review the user’s
manual. A check of the PRODUCT controls and features might save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit
and transportation and are responsible for delivery or handling charges incurred in the
transport of the PRODUCT(s) to the service location. The manufacturer will return repaired or
replaced PRODUCT under this limited warranty. Transportation, delivery or handling charges
are prepaid. The manufacturer assumes no risk for damage or loss of the PRODUCT in transit.
If the PRODUCT failure is not covered by this limited warranty, or proof of purchase does not
meet the terms of this limited warranty, the manufacturer notifies you and requests that you
authorize the cost of repair prior to any further repair activity. You must pay for the cost of
repair and return shipping costs for the repair of products that are not covered by this limited
warranty.
What must you return with the PRODUCT to get warranty service?
You must:
Return the entire original package and contents including the PRODUCT to the service
location along with a description of the malfunction or difficulty; and
Include “valid proof of purchase” (sales receipt) identifying the PRODUCT purchased
(PRODUCT model) and the date of purchase or receipt; and
Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and the manufacturer
of this AT&T branded PRODUCT. It supersedes all other written or oral communications
related to this PRODUCT. The manufacturer provides no other warranties for this PRODUCT.
The warranty exclusively describes all of the manufacturer’s responsibilities regarding the
PRODUCT. There are no other express warranties. No one is authorized to make modifications
to this limited warranty and you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you might also
have other rights that vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the PRODUCT is fit for ordinary use) are limited
to one year from date of purchase. Some states/provinces do not allow limitations on how
long an implied warranty lasts, so the above limitation might not apply to you. In no event
shall the manufacturer be liable for any indirect, special, incidental, consequential, or similar
damages (including, but not limited to lost profits or revenue, inability to use the PRODUCT
or other associated equipment, the cost of substitute equipment, and claims by third parties)
resulting from the use of this PRODUCT. Some states/provinces do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion might
not apply to you.
Please retain your original sales receipt as proof of purchase.
5.
6.
a.
b.
c.
7.
Limited warranty
94
Appendix
Technical specifications
RF frequency band 1921.536MHz — 1928.448MHz
Channels 5
Operating temperature 32°F — 122°F
0°C — 50°C
Telephone base voltage
(AC voltage, 60Hz)
96 — 129 Vrms
Telephone base voltage
(AC adapter output)
6VDC @400mA
Handset voltage 2.4 — 3.2 VDC
Charger voltage
(AC adapter output)
6VAC @300mA
Replacement battery 2.4V 750mAH
Operation time* Talk time (handset): up to eight hours
Talk time (speakerphone): up to five hours
Standby: up to seven days
* Operating times varies depending on your actual use and the age of the battery.
DECT 6.0 digital technology
The AT&T DECT 6.0 products offer unsurpassed range performance and sound
clarity. This is achieved through a unique antenna design and advances in
noise-filtering technology. An independent laboratory has confirmed that
AT&T DECT 6.0 products perform up to 45% better in range competitions.
Now calls can be taken in the basement, backyard and garage with
exceptional sound quality.
Telephone operating range
This cordless telephone operates within the maximum power allowed by
the Federal Communications Commission (FCC). Even so, this handset and
telephone base can communicate over only a certain distance — which can
vary with the locations of the telephone base and handset, the weather, and
the construction of your home or office.
Extended range and clarity
This telephone base comes with an antenna which gives much better clarity
and covers a longer range than before.

User’s manual
TL92270/TL92370
DECT 6.0 cordless
telephone/answering
system with BLUETOOTHBLUETOOTH®
wireless technology
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by Advanced
American Telephones and its parent, VTech Holdings Limited, is under license. VTech Holdings Limited is a
member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.
© 2009 Advanced American Telephones. All Rights Reserved. AT&T and
the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219. Printed in China.
Congratulations
on purchasing your new AT&T product. Before using this AT&T product, please
read the Important safety information on pages 88-89 of this user’s manual.
Please thoroughly read the user’s manual for all the feature operations and
troubleshooting information you need to install and operate your new AT&T
product. You can also visit our website at www.telephones.att.com or
call 1 [phone]. In Canada, dial 1 [phone].
The ENERGY STAR® program (www.energystar.gov)
recognizes and encourages the use of products that save
energy and help protect our environment. We are proud to
mark this product with the ENERGY STAR® label indicating it
meets the latest energy efficiency guidelines.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Telephones identified with this logo have reduced noise
and interference when used with most T-coil equipped
hearing aids and cochlear implants. The TIA-1083 Compliant
Logo is a trademark of the Telecommunications Industry
Association. Used under license.
Model #: TL92270 (two handsets)
TL92370 (three handsets)
Type: DECT 6.0 cordless telephone/answering system
with Bluetooth wireless technology
Serial #:
Purchase date:
Place of purchase:
Both the model and serial number of your AT&T product can be found on the
bottom of the telephone base.

Parts checklist
Your telephone package contains the following items. Save your sales receipt
and original packaging in the event warranty service is necessary.
Telephone line cord
Power adapter for
telephone base
Cordless handset
(2 for TL92270)
(3 for TL92370)
Telephone base
Charger for cordless
handset with power
adapter installed
(1 for TL92270)
(2 for TL92370) Wall-mount bracket
Battery for cordless
handset
(2 for TL92270)
(3 for TL92370)
Battery compartment
cover
(2 for TL92270)
(3 for TL92370)
User’s manual Quick start guide
User’s manual
TL92270/TL92370
DECT 6.0 cordless
telephone/answering
system with BLUETOOTHBLUETOOTH®
wireless technology
Quick start guide
TL92270/TL92370
DECT 6.0 cordless
telephone/answering
system with BLUETOOTHBLUETOOTH®
wireless technology
User’s manual
TL92270/TL92370
DECT 6.0 cordless
telephone/answering
system with BLUETOOTHBLUETOOTH®
wireless technology
Table of contents
Getting started
Quick reference guide -
telephone base...................................... 1
Quick reference guide - handset.. 2
Installation ............................................... 5
Telephone base installation ............ 6
Battery installation & charging...... 8
Battery charging ................................... 8
Battery installation .............................. 9
Wall-mount installation...................10
Tabletop to wall-mount
installation .............................................10
Wall-mount to tabletop
installation .............................................11
Bluetooth
Introducing Bluetooth......................12
Glossary of terms...............................13
Bluetooth setup...................................14
Pairing a device...................................14
Auto connection..................................15
Pair a headset......................................16
Auto connection..................................17
Paired devices........................................ 18
Rename a paired device..................18
Remove a paired device..................19
Active devices ........................................ 20
Replace an active device................21
Bluetooth operation..........................22
Add an active device ........................22
Remove an active device................23
Change PIN............................................23
Download directory...........................24
Interruption to directory
download................................................26
View the directory download
information ............................................26
Handset settings
Telephone settings.............................27
Ringer volume......................................27
Ringer tone............................................27
LCD language .......................................28
Clear voicemail....................................28
Key tone..................................................29
Website....................................................29
Set date/time .......................................30
CID time synchronization................31
Dial mode...............................................31
Home area code..................................32
Cell area code......................................32
Answer ON/OFF..................................33
Announcement ....................................34
Delete your announcement...........35
Call screening.......................................36
Number of rings..................................36
Remote access code.........................37
Message alert tone............................37
Telephone operation
Making, answering and ending a
call .............................................................38
Making a call.........................................38
Options while on calls .....................39
Handset speakerphone....................42
Volume control ....................................42
Silencing the ringer...........................42
Mute ..........................................................42
Temporary tone dialing ...................43
Hold...........................................................43
Handset locator...................................44

Chain dialing.........................................45
Redial stack ...........................................46
Review the redial list........................46
Dial a redial entry...............................46
Save a redial entry to the
directory..................................................47
Delete a redial entry.........................47
Intercom..................................................48
To initiate an intercom call............48
Answer an incoming call during
an intercom call..................................49
Call transfer and sharing................50
Share an outside call........................50
Transferring an outside call...........50
Equalizer setting .................................52
Directory
Directory .................................................53
Create a new entry in the home
directory..................................................54
Character chart....................................55
Review the directory.........................56
3-character alphabetical search.56
Dial, Edit or delete a directory.....57
Dial a directory entry........................57
Edit the type of a directory
entry..........................................................58
Delete a directory entry..................58
Remove a downloaded
directory..................................................58
Caller ID
About caller ID.....................................59
Information about caller ID with
call waiting ............................................59
Caller ID history ..................................60
Caller ID operation ............................61
Memory match.....................................61
Missed calls indicator.......................61
Caller ID operation ............................62
Review the call log............................62
View dialing options..........................62
Dial a call log entry...........................63
Save a call log entry to the
directory..................................................63
To delete a single entry ..................64
To delete all entries ..........................64
Reasons for missing caller ID
information ............................................64
Answering system
About the answering system........65
Answering system and
voicemail.................................................65
Message capacity ...............................65
New message indication.................66
Call screening at the telephone
base...........................................................66
Call intercept ........................................66
Telephone base ringer volume ....66
Temporarily turning off the
message alert tone............................66
Voice prompts ......................................66
Message playback ..............................67
Delete all old messages..................68
Record and play memos .................68
To play back a memo.......................68
Base message counter
displays....................................................69
Message window displays..............69
Remote access.....................................70
To remotely access the
answering system...............................70
Remote commands............................70
Appendix
Handset screen icons.......................71
Alert tones and lights.......................72
Handset alert tones...........................72
Telephone base alert tones...........72
Handset indicator lights..................72
Telephone base indicator
lights .........................................................72
Screen messages................................73
Display screen messages................73
Expand your telephone system...76
Add and register a handset
(optional).................................................76
Replace a handset .............................77
To deregister all handsets..............77
Maintenance..........................................87
Important safety information........88
Table of content
Safety information..............................88
Especially about corded
telephones .............................................88
Precautions for users of implanted
cardiac pacemakers...........................89
Pacemaker patients...........................89
Especially about telephone
answering systems.............................89
FCC part 68 and ACTA.....................90
FCC part 15 ...........................................91
Limited warranty.................................92
Technical specifications...................94
DECT 6.0 digital technology..........94
Telephone operating range...........94
Extended range and clarity ...........94
Index ..............................................................95
Table of content