ATD Tools ATD-701 User manual

ATD-701
Non-contact Infrared Thermometer
Instruction manual
1. Introduction
Compact, rugged and easy to use. Just aim and push the
button, read target surface temperatures in less than a
second. Safely measure surface temperatures of hot,
hazardous or hard-to-reach objects without contact.
How it works
Infrared thermometer measures the surface temperature of
an object. The unit’s optics sense emitted, reflected, and
transmitted energy which is collect and focused onto a
detector. The unit’s electronics transmitted energy which is
display on the unit. For increased ease and accuracy the
laser pointer makes aiming even more precise.
Cautions
Infrared thermometer should be protected from the
following:
--EMF (electro-magnetic fields) from arc welders, induction
heaters.
--Thermal shock (cause by large or abrupt ambient
temperature changes allow 1 hour for unit to stabilize before
use).
--Do not leave the unit on or near objects of high
temperature.
Warning
Do not point laser at eye or indirectly off reflective surfaces.
1. When take measurement, point thermometer toward
the object to be measured and hold the red trigger. The
object under test should be larger than the spot size
calculated by the field of view diagram.
2. Distance ＆spot size: As the distance from the object
increase, the spot size of measuring area becomes
larger.
3. Field of view: Make sure the target is larger than the
unit’s spot size. The smaller the target, the closer
measuring distance. When accuracy is critical, make
sure the target is at least twice as large as the spot size.
4. Emissivity: Most organic materials and painted or
oxidized surfaces have an emissivity of 0.95. Inaccurate
readings will result from measuring shiny or polished
metal surfaces. To compensate, cover the surface to be
measured with masking tape or flat black paint.
Measure the tape or painted surface when the tape or
painted reach the same temperature as the material
underneath.
2. Quick start instruction
1. Press battery door clip, install battery correctly. Pull the
trigger, LCD display reading ＆battery icon. Release
the trigger and the reading will hold for 7 seconds.
LCD display:
ALaser pointer turn on prompt
B Alarm of high temperature prompt
C Alarm of Low temperature prompt
DData Hold
EMeasure result
F Emissivity
G Temperature unit：℃
H Temperature unit：℉

2. Locating a hot spot aim the thermometer outside the
area of interest, then scan across with up and down
motions until you locate the hot spot.(please turn on the
laser to for accurate measuring)
3. Diagram description
(1) Trigger: Press for turn on, and then display test result
and hold data 7 seconds automatically ("HOLD") after
unclamping switch. Turn off automatically after 10
seconds without operate.
(2) Laser pointer button ：press it for turn on laser
pointer, press again for turn off.
(3) Back light /Up button ：In “Alarm temperature”
and “setting emissivity” mode for adjust value up. In
other mode for turn on back light. When product
working, press it for turn on back light, press again for
turn off.
(4) MODE button：Press MODE button for cycle options
- MAX - AVG - MIN –HAL –LAL mode
A、MAX：Measure maximum data current；
B、MIN：Measure minimum data current；；
C、AVG：Calculate the average of all measure data；
D、HAL：Alarm of high temperature. Option HAL mode,
press “UP or DN ”button for set alarm temperature.
When LCD display ”H” means measure result exceeded
the alarm temperature；
E、LAL：Alarm of low temperature. Option HAL mode,
press “UP or DN ”button for set alarm temperature.
When LCD display ”L” means measure result under the
alarm temperature；
(5) T/ DN button ：In “Alarm temperature” and “setting
emissivity” mode for adjust value down . When turn on
product and press direct for ℃/  select.
(6) SET button：Press for setting emissivity. And press
“UP or DN” for adjust from 0.1~1.0. Press SET button
again for exit setting mode.
(7) LCD display
(8) Battery door: When replace battery, please using
the finger indents to pull open the battery door.
3. Maintenance
1) Lens cleaning: Blow off lose particles using clean
compressed air. Gently brush remaining debris away
with a moist cotton cloth.
2) Case cleaning: Clean the case with a damp
sponge/cloth and mild soap.
3) Please take out the battery when not using for a long
time.
Note:
1) Do not use solvent to clean lens.
2) Do not submerge the unit in water.
4. Specifications
Temperature
range Infrared：-30℃to 550℃(-22 to1022℉)
Accuracy
±3℃or ±3%of rdg,-30℃to 0℃(-22 to 32)
±2℃or±2% of rdg,0℃to 100℃(32 to 212℉)
±3℃or ±3% of rdg,≥100℃(212℉)
Display spot size 10:1
Repeatability 1%of reading or ±1℃
Response time 500ms
Spectral response 8-14um
Emissivity 0.1～1.0 adjustable
Relative humidity 10-95% RH non-condensing
Operating
temperature 0℃to ~60℃(32 to 140℉)
Storage
temperature -20~60℃(-4~140℉) without battery
Power Supply 9V 6F22 battery
Battery life Laser models:12 hrs
Product size 165×80×41mm
Product weight 155g（without battery）
Note:
Display “AL” means ambient temp lower than 0”;
Display “AH” means ambient temp higher than 60℃”;
Display above code in normal ambient temp, probable
means this meter was broken.
Attached list ：Applicable Emissivity for
Different Material ( For reference only)
Material Emissivity Material Emissivity
Aluminum 0.30 Iron 0.70
Asbestos 0.95 Lead 0.50
Asphalt 0.95 Limestone 0.98
Basalt 0.70 Oil 0.94
Brass 0.50 Paint 0.93
Brick 0.90 Paper 0.95
Carbon 0.85 Plastic 0.95
Ceramic 0.95 Rubber 0.95
Concrete 0.95 Sand 0.90
Copper 0.95 Skin 0.98
Dirt 0.94 Snow 0.90
Frozen food 0.90 Steel 0.80
Hot Food 0.93 Textiles 0.94
Glass(plate) 0.85 Water 0.93
Ice 0.98 Wood 0.94