Atdec AWM-A46 User manual

AWM-A46 Page 1 of 4
Installation Guide
AWM-A46
460 Arm
COMPONENT CHECKLIST REQUIRED TOOLS
A
Monitor
arm
(x1)
B
VESA
head
(x1)
D
Screw
M4x12mm
(x4)
E
Screw
M4x10mm
(x4)
F
Screw
M4x8mm
(x4)
G
Spacer
10mm
(x4)
H
Security
screw
(x1)
I
4mm
allen key
(x1)
C
Channel
clamp
(x1)
WEIGHT RANGE
0 - 12kg
(0 - 26.5lbs)
• Phillips Head Screwdriver
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! This product is compatible with Atdec modular (AWM) products.

AWM-A46 Page 2 of 4
1. Optional 180� rotation limiter
3. Mounting arm assembly
3.1 Slide arm assembly into channel 3.2 Move to desired height
Note: Ensure
clamp lever is
vertical and
unlocked
Note: Squeeze and
hold clamp jaws
before inserting Post
3.3 Lock at preferred height
by pushing lever down
Wall Channel
‘Click’
Note that the arm is set to rotate 360� by default. To reduce the arm’s rotation to 180�, follow the steps below.
1.1 Remove plastic sleeve 1.2 Remove rotation ring 1.3 Place rotation ring in
desired orientation/position
Note: Place the rotation ring
depending on what post channel
the arm will be attached to. The tag
should always face towards the user.
1. Press
2. Lift
180°
360°
OR
Default
Position
Flipped
Position
Tag
2. Fit arm onto channel clamp
2.1 Push arm onto clamp 2.2 Ensure arm is fully pushed onto clamp 2.3 Lightly tighten set screw
Tip: Check that
rotation of the
arm is smooth
Fit top cap on post

AWM-A46 Page 3 of 4
4. Attach VESA head to monitor
100mm
75mm
100mm 75mm
Flush Spacer
4.2 Ensure the monitor is attached correctly 4.3 VESA mounting compatibility
100mm
75mm
100mm 75mm
Flush Spacer
Note: For other sizes, use a suitable
adaptor plate
4.1 Screw the VESA head onto monitor
Note: spacers may be required for
curved, recessed or uneven monitor
surfaces.
Tighten
Loosen
Tighten
Loosen
5. Mount monitor
Monitor arm
5.1 Insert VESA head into the monitor arm 5.3 Push the lever down to secure
it to the arm assembly
5.2 Ensure that the VESA head sits flush within
the monitor arm. There should be no gap
Gap No gap
6. Adjust tilt tension & Install security screw
6.1 To make for easy tilt adjustment and to prevent the monitor
from falling forward, adjust the tension as show below
Note: Support
monitor while
adjusting.
6.2 OPTIONAL security screw
To install the optional security screw tilt the head upwards

AWM-A46 Page 4 of 4
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20171206B
Note: The cable cover shown,
does not come with all posts
7.4 To reposition the cable cover, pull it
straight up and out of the post and insert
it into any of the available channels
Cable cover
Cable
Cover
Desk
Clamp
7.1 Push the cable down into the cable clip
Note: Cable clips do not
come with all posts
7.6 Feed remaining cable into cover
7.5 Loop cable and insert into cable cover
7.2 Push cable clip into post channel
7. Post cable management
7.3 Recommended post cable cover
position for double or triple arm set-ups
Note
Ensure enough cable
slack is given to allow for
movement of the monitor
Push
6. Monitor arm cable management
6.1 Plug cables into the monitor and route
the cables down the arm using the cable
hooks and clips
Alternative cable
cover positions