Atdec TH-1040-CTS User manual

TH-1040-CT Page 1 of 6
Installation Guide
TH-1040-CTS
TH-1040-CTL
TH-1040-CT-B2B
TH-1040-CT-RCK
TH-1040-CT-DV
1040 Ceiling Mount
COMPONENT CHECKLIST
REQUIRED TOOLS
• Power drill
• 7mm Drill Bit
• 12mm Masonry Drill Bit
• Phillips head screw driver
• 17mm Socket Wrench or
Shifter
A
Pole
Assembly
F
Coach
Screw
(x4)
H
Nylon
Anchor
(x4)
I
M4/M5/M10
Washer
(x4 each)
K
M6/M8
Spacer
(x4)
J
M4/M5
Spacer
(x4)
G
2.5mm/3mm/
5mm Hex
Keys
C
Mounting Plate
Cover
D
False Ceiling
Cover
E
VESA Plate
B
Mounting Plate
M
Set
Screw
L
Security
Screw
N
M4x16mm
M4x25mm
(x4 each)
O
M5x16mm
M5x25mm
(x4 each)
P
M6x16mm
M6x30mm
(x4 each)
Q
M8x16mm
M8x30mm
(x4 each)
Maximum pole capacity
0 - 50kg
(0 - 110lb)
WEIGHT RANGE
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Themaximumpolecapacitydenestheweightcapacityofthecompletemountingsolution,notindividual
display mounts.
! Failure to mount this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! Thisproductshouldonlybeinstalledbyprofessionalinstallersofgoodmechanicalaptitude,whohaveexperiencewith
buildingconstruction,andfullyunderstandtheseinstructionsandtheconsequencesofincorrectinstallation.
! CeilingMountonlyachievesmaximumweightratingwhenappropriatelyfastenedtoaceilingofadequate
structural capacity.
! Professionalinstallertoensureadequatestructuralcapacityofceiling(includingappropriatesafetyfactor)tosupport
totalweightofallequipmentbeingmounted.
! Drillingintoelectricalwirescancausedeath-useappropriateequipmentandcautionwhendrillingholesinceilingsto
avoidelectricalcables,waterpipesandgaspipes.Donotdrillintostructuresunlessestablishedit’ssafetodoso.

TH-1040-CT Page 2 of 6
A
C
PUSH
2. Install Mounting Plate Cover
B
TWIST
G- 3mm
Hex Key
M
3.1. Screw Pole Assembly Ainto Mounting Plate B
by twisting top half of the Pole Assembly only.
3.2. Insert Set Screw Minto the Mounting Plate to lock the
Pole Assembly in position.
3. Attach Pole Assembly to Mounting Plate
A
C
4. Position Mounting Plate Cover
1. Install Mounting Plate
• Use Mounting Plate Bas a template to mark hole positions.
• Use a suitable power drill to drill Ø7x70mm holes for
timber joist installations or Ø12x70mm for concrete.
Masonry Ceiling Timber Ceiling
H
B
F
I - M10
Washer
B
F
I - M10
Washer
OR
5. Set length of Pole
LOOSEN
Socket Cap Screw
G- 5mm Hex Key
ADJUST
HEIGHT
5.1. Whilst supporting the lower half of Pole
Assembly loosen the socket cap screws (x2).
5.2. Slide Pole Assembly to the desired height.
• Please choose fasteners that will suit your
installation,consultaqualiedengineerprior
to installing.
• Ensureceilingmountisvertical,thisproduct
will not suit slanted ceilings.
• Usegoodqualitystudndertoposition
mounting fasteners in the centre of the studs.
• Avoid mortar joins.
• Formetalbeams,pleaseconsultqualied
engineer.

TH-1040-CT Page 3 of 6
7.1. Angle the display and
hook the slot on the VESA
Plate Eto the Ball Mount
on the Pole Assembly A.
Press the buttons on either
side of the Ball Mount
and gently apply pressure
to the lower half of the
display to ensure the VESA
Plateisrmlyattachedthe
to the Ball Mount. It should
sit parallel on the ball
mount.
7.2. (OPTIONAL) Insert Security Screw Lusing
Phillips head screwdriver.
7. Attach display to Pole Assembly
Security
Screw L
TIGHTEN
FIRMLY
Set Screw
Pole Joint
2.5mm
Hex Key
5.3. Tighten the socket cap
screws (x2) to set the height.
5.4.Ifnecessary,usethesetscrewsoneithersideofthe
pole joint to correct the alignment of the lower pole.
6. Attach VESA Plate to display
TOP
E
Cable
Access Port
8.1. Feed cables down the Pole Assembly
through the cable access port.
8.2. Pull cables out
from lower half of the
Pole Assembly and
connect to display.
8. Cable management
Flush
Too long Too short
Spacer
NOTE:
• Always use a washer.
• Ensure the display brackets are
not loose and screws are not
forced too deep into the display.
• If spacers are
needed, use the
shortest possible
combination
between the
display bracket
and the display.

TH-1040-CT Page 4 of 6
False Ceiling
Cover
CLICK
Lower Pole
PUSH
If the Lower Pole hangs
belowasuspendedceiling,
clip the False Ceiling Cover
overtheLowerPole,and
push up to the ceiling.
9. (OPTIONAL) Install False Ceiling Cover
ADJUSTMENTS
PAN
TILT
G- 3mm Hex Key
Firmly grip the display with two hands to
pan,tiltthedisplayupto20degreesand
rotate the display up to 90 degrees.
If the display is too
loose or too stiff
toposition,usethe
3mm Hex Key Gto
evenly tighten or
loosen the ball joint
screws in small
increments to the
desired tension.
NOTE: Ball joint tension
mayneedtobeloosened,
adjusted and tightened to
set the desired position.
Ball Joint TensionDisplay Position
WARNING: Whenrotatingthedisplay,ensurethehookdetailonthedisplaybracketneverfacesdownwards.
Socket Cap Screw
G- 5mm Hex Key
Display Height
Socket Cap Screw
G- 5mm Hex Key
Socket Cap Screw
G- 5mm Hex Key
WARNING: Display must be removed.
Loosen Socket Cap Screws (x2) on the collar.
Slide the height of the Slide the
heightofthecollarasrequired.
Tighten Socket Cap Screws to lock.
Follow guide from step 7.

TH-1040-CT Page 5 of 6
Installation Guide
TH-1040-CT-B2B
TH-1040-CT-RCK
TH-1040-CT-DV
1040 Ceiling Tilt Accessories
Maximum pole capacity
0 - 50kg
(0 - 110lb)
WEIGHT RANGE
1040 Ceiling Back to Back Kit COMPONENT CHECKLIST
A
VESA Plate
B
Mount Head
Accessory
E
Security
Screw
(optional)
F
M4 Washer
M5 Washer
(x4 each)
K
M6x16mm
M6x30mm
(x4 each)
L
M8x16mm
M8x30mm
(x4 each)
D
3mm
Hex
Key
C
5mm
Hex
Key
I
M4x16mm
M4x25mm
(x4 each)
J
M5x16mm
M5x25mm
(x4 each)
H
M6/8
Spacer
(x4)
G
M4/5
Spacer
(x4)
Maximum pole capacity
0 - 50kg
(0 - 110lb)
WEIGHT RANGE
1040 Ceiling Rear Collar Kit COMPONENT CHECKLIST
A
Mount Head
Rear
B
M6x20mm
Socket Cap
Screw (x2)
TH-1040-CT-DV 1040 Ceiling Tilt Double Vertical consists of:
• TH-1040-CT-B2B 1040 Ceiling Back to Back Kit
• TH-1040-CT-RCK 1040 Ceiling Rear Collar Kit

TH-1040-CT Page 6 of 6
No portion of this document or any artwork contained herein should be reproduced in any way without
theexpresswrittenconsentofAtdecPtyLtd.Duetocontinuingproductdevelopment,themanufacturer
reservestherighttoalterspecicationswithoutnotice.©20230904
C- 5mm Hex Key
Socket Cap Screw
Mount Head Rear
Socket Cap Screw
Remove back half of the existing
Mount Head by removing Socket Cap
Screws (x2).
WARNING: Display must be removed.
NOTE: Keep Socket Cap Screws for
Step 2.
1. Remove Back of Existing Mount Head
Socket Cap Screw
Socket Cap Screw
5mm Hex Key
Mount Head
Accessory
2.1 Attach the
Mount Head
Accessory with
the Socket Cap
Screws (x2).
Tighten screws
rmlyandequally.
2.2 Refer to TH-1040-CTS/
TH-1040-CTL Installation
Instructions,Step6.Attach
VESA plate to display.
2. Install Mount Head Accessory
TH-1040-CT-B2B 1040 Ceiling Back to Back Kit
TH-1040-CT-DV 1040 Ceiling Tilt Double Vertical
Socket Cap
Screw
Socket Cap
Screw
Mount
Head
Rear
Mount Head
Accessory
5mm
Hex Key
1.2 Refer to
TH-1040-CTS/
TH-1040-CTL
Installation
Instructions,Step
6. Attach VESA
plate to display.
1.1 Attach Mount Head
Rear to Mount Head
Accessory with Socket
Cap Screws (x2).
1. Remove Back of Existing Mount Head
TH-1040-CT-RCK 1040 Ceiling Rear Collar Kit
1. Replace Back of Existing Mount Head
1.3RefertoTH-1040-CTS/TH-1040-CTLInstallationInstructions,Step7.AttachdisplaytoPoleAssembly.
1.1 Remove back half of the
existing Mount Head by removing
Socket Cap Screws (x2).
WARNING: Display must be
removed,ensurecablesand
security screw are removed prior.
NOTE: Keep Socket Cap Screws
for Step 1.2.
1.2 Attach the Mount Head Rear with
the Socket Cap Screws (x2).