Atdec AWM-A13 User manual

AWM-A13 Page 1 of 4
Installation Guide
AWM-A13
130 Arm
COMPONENT CHECKLIST REQUIRED TOOLS
WEIGHT RANGE
A
Monitor
arm
(x1)
C
Channel
clamp
(x1)
B
VESA
head
(x1)
D
Screw
M4x12mm
(x4)
E
Screw
M4x10mm
(x4)
F
Screw
M4x8mm
(x4)
G
Spacer
10mm
(x4)
H
Security
screw
(x4)
I
4mm
allen key
(x4)
0 - 12kg
(0 - 26.5lbs)
• Phillips Head Screwdriver
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! This product is compatible with Atdec modular (AWM) products.

AWM-A13 Page 2 of 4
2. Fit arm onto channel clamp
1. Optional 180� rotation limiter
3. Mounting arm assembly
2.1 Push arm onto clamp
1.1 Remove plastic sleeve
2.2 Ensure arm is fully pushed onto clamp
1.2 Remove rotation ring
2.3 Lightly tighten set screw
1.3 Place rotation ring in
desired orientation/position
Note: Place the rotation ring
depending on what post channel
the arm will be attached to. The tag
should always face towards the user
1. Press
2. Lift
180°
360°
OR
Default
Position
Flipped
Position
Tag
3.1 Slide arm assembly into channel 3.2 Move to desired height
Fit top cap on post
Note: Ensure
clamp lever is
vertical and
unlocked
Note: Squeeze and
hold clamp jaws before
inserting into channel Post
3.3 Lock at preferred height
by pushing lever down
Wall Channel
‘Click’
Note that the arm is set to rotate 360� by default. To reduce the arm’s rotation to 180�, follow the steps below.
Tip: Check that
rotation of the
arm is smooth

AWM-A13 Page 3 of 4
4. Attach VESA head to monitor
100mm
75mm
100mm 75mm
Flush Spacer
4.1 Screw the VESA head onto monitor
Note spacers may be required for
curved, recessed or uneven monitor
surfaces.
4.2 Ensure the monitor is attached correctly 4.3 VESA mounting compatibility
100mm
75mm
100mm 75mm
Flush Spacer
For other sizes, use a suitable adaptor plate
Tighten
Loosen
Tighten
Loosen
5. Mount monitor
Monitor arm
5.1 Insert VESA head into the monitor arm 5.3 Push the lever down to secure
it to the arm assembly
5.2 Ensure that the VESA head sits flush within
the monitor arm. There should be no gap
Gap No gap
6. Adjust tilt tension & Install security screw
6.1 To make for easy tilt adjustment and to prevent the monitor
from falling forward, adjust the tension as show below
Note: Support
monitor while
adjusting
6.2 OPTIONAL security screw
To install the optional security screw tilt the head upwards

AWM-A13 Page 4 of 4
6. Monitor arm cable management
Note: The cable cover shown,
does not come with all posts
7.4 To reposition the cable cover, pull it
straight up and out of the post and insert
it into any of the available channels
Cable cover
Cable
Cover
Desk
Clamp
7.1 Push the cable down into the cable clip
Note: Cable clips do not
come with all posts
7.6 Feed remaining cable into cover7.5 Loop cable and insert into cable cover
7.2 Push cable clip into post channel
7. Post cable management
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20171206B
Alternative cable
cover positions
7.3 Recommended post cable cover
position for double or triple arm set-ups
6.1 Plug cables into the
monitor and route the cables
down the arm using the cable
hooks and clips
Important:
Ensure enough cable slack is given
to allow for movement of the monitor