Atel Arch+ W02 User manual

Quick Start Guide About your W02
Device Display
W02
4G LTE Supported Bands –2/4/5/12/13/66/71
4G Hotspot
WARNING! Please only use an approved charger to charge your
W02. Improper handling of the charging port, as well as the use
of an incompatible charger, may cause damage to your device
and void the warranty.

Key
Power Button
Power on/off for the W02. Quick press the power key two
times, start WPS.
Type C Charging Port
The USB charger connects here.
Battery
Insert the battery to align with the batter contacts.
Reset
To perform a reset of your device, use an unfolded paper clip,
insert it into the RST pin hole, and push down for 3 seconds
then release.
SIM Card
Remove the battery cover from the back of your W02 and
remove the battery. Slide the SIM door open by pressing
down and sliding, as the image shows below. Make sure the
SIM is placed properly before pushing down and sliding the
door back up to close it.
Wi-Fi Network Name
(SSID) / Password
You can locate the SSID and
password on the device label in the
battery compartment. Use the
SSID/password to establish your
internet connection.
Setting up your W02
Turning your W01 On/Off
First, insert a compatible SIM card into your W02. Then insert
the battery and close the battery cover. To turn your W02 on,
press and hold the Power button. To turn it off, press and hold
the Power button until you see the LCD go off.
Charging your W02
To charge your device, insert the
USB Type C cable into the charging
port and plug into the charger.

System Requirements
Your W02 is compatible with any device with Wi-Fi capability
and an Internet browser. It is compatible with all major
operating systems and the latest versions of browsers.
Device Settings
You can access your Mobile Hotspot (W02) Online Device
Management Portal to view and edit your settings.
1. Connect your Wi-Fi capable device (e.g. laptop) to your
W02 Wi-Fi network.
2. Open a browser (e.g. Chrome) and enter
http://192.168.0.01 in the URL address bar.
3. Your Online Portal login might be unique to your
device. In this case, please check your device label for
the unique Online Portal password.
You can change the Admin password from the hotspot Online
Portal under SETTINGS > Device Settings. Once changed, you
must use the new password to login to the Online Portal.
Different browsers may have different security settings for
HTTPS. Additional steps may be needed to access the Online
Portal using https://192.168.0.1. For example, for Microsoft
Edge browser, you will need to click “Advanced > Continue to
192.168.0.1 (unsafe)” in order to access the interface.
Managing Wi-Fi Networks + Connections
From the Online Portal, you can change your WI-Fi Settings.
For example, the maximum WI-Fi connection is defaulted to
15. You can set it to any value between 1 and 15. The Wi-Fi
band is defaulted to 2.4GHz and you can change it to 5GHz.
Please note that the Online Portal is currently available only in English.

Connecting to the Internet
1. Open the Wi-Fi settings of your device that you want to
connect to the W02.
2. Select the SSID of your W02 from the available
network list.
3. When prompted, enter your W02 password (located on
the device label in the battery compartment).
LCD Indicators Key
Factory Reset of your W02
You can reset your W02 to factory settings with the W02 reset
pin hole or via the Online Portal.
NOTE: Resetting your W02 will disconnect all devices
connected to your W02. All device settings including network
name and password will be reset back to factory defaults.
•To reset from the Online Portal, click About > Backup
and Restore > Restore to Factory Defaults.
•To reset using the reset pin hole
on the W02:
1. Make sure your W02 is on.
2. Remove the battery cover
from the back of your W02.
3. Insert an unfolded paper
clip into the Reset pin hole
and press until the W02
LCD is lit.
Reset
For more information
Please refer to your W02 User Manual for additional
information or visit the ATEL USA website Device and Support
pages at www.ATEL-USA.com.
Contact us at: [e-mail]
© 2021 Asiatelco Technologies, Inc. All Rights Reserved.