ATEN PG95230 User manual

PG95230 / PG95330
PG96230 / PG96330
PG98230 / PG98330
3-Phase 30-Outlet 0U eco PDU
User Manual

eco PDU PG Series User Manual
6
Compliance Statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC ules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC ules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Warning
Operation of this equipment in a residential environment could cause radio
interference.
Achtung
Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.

eco PDU PE Series User Manual
7
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
Ro S
This product is oHS compliant.
PE Device Safety Notice
 Set the maximum permissible breaker protection in the building circuitry to the
current rating specified on the rating plate. Observe all national regulations and
safety codes as well as deviations for breakers.
 Only connect the PE Device to a grounded power outlet or a grounded system!
 Make sure that the total current input of the connected systems does not exceed
the current rating specified on the rating plate of the PE Device.
 There is a risk of explosion if the battery is replaced with an incorrect type.
Dispose of used batteries according to the relevant instructions.

eco PDU PG Series User Manual
8
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
User Notice
All information, documentation, and specifications contained in this manual are subject
to change without prior notification by the manufacturer. The manufacturer makes no
representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranties as to merchantability or fitness for any
particular purpose. Any of the manufacturer's software described in this manual is sold
or licensed as is. Should the programs prove defective following their purchase, the
buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of
all necessary servicing, repair and any incidental or consequential damages resulting
from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV interference
caused by unauthorized modifications to this device. It is the responsibility of the user
to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation of this
system if the correct operational voltage setting was not selected prior to operation.
PLEASE VE IFY THAT THE VOLTAGE SETTING IS CO ECT BEFO E USE.
If any bodily injury or property damage with respect to operation of the product results
from users not having installed the product in accordance with the instructions provided
in the product’s user manual, or the product is used in an environment with a current
load over the designed specifications of the product, ATEN is not liable for any loss or
damage.
International http://eservice.aten.com
International 886- -869 -6959
China 86-400--810-0-810
Japan 81-3-5615-5811
Korea 8 - -467-6789
North America 1-888-999-ATEN ext 4988
1-949-4 8-1111

eco PDU PE Series User Manual
9
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
eseller. Visit ATEN on the Web for a list of locations and telephone numbers:
International http://www.aten.com
North America http://www.aten-usa.com

eco PDU PG Series User Manual
10
Package Contents
Check to make sure that all the components are in working order. If you
encounter any problem, please contact your dealer.
The eco PDU PG series standard package consists of:
1 3-Phase 30-Outlet 0U eco PDU unit
1 rack mount kit
1 J-45 to DB-9 cable
1 full-panel colored sticker
1 user instructions

eco PDU PE Series User Manual
11
Contents
Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Chapter 1. Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Proactive Overload Protection (POP) . . . . . . . . . . . . . . . . . . . . . . . . . 19
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
Cable Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Status Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2. Hardware Setup
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rack Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rack Mount Lock Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PDU Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Securing the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Chapter 3. Basic Operation and
irst-Time Setup
Operation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
eco DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
First-Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Changing the Administrator Login . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Moving On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

eco PDU PG Series User Manual
1
Chapter 4. Logging In
Logging In. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
The eco PDU Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Page Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Chapter 5. Energy
Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
PDU Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Sensor Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Inlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bank Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
POP Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Power On Time Schedule Settings . . . . . . . . . . . . . . . . . . . . . . . . 46
Bank Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Bank POP Priority List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Outlet Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Chapter 6. User Management
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Administrator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SNMPv3 Account Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SNMPv1/v c Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Chapter 7. Log
Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
The System Log Event List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Notification Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Chapter 8. Setup
Device Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Device Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Service Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Serial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

eco PDU PE Series User Manual
13
IPv4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
IPv6 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Event Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
SMTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
SNMP Trap Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Syslog Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Manual Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Network Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Finishing Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Working Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
TLS Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
IPInstaller Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Session Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Account Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
IP Filter / Mac Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Authentication & Authorization. . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Private Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Wireless Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
IPv4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
IPv6 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Adding a PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Deleting a PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting a PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Discovering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Scheduler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Creating an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Chapter 9. PDU
PDU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Upgrade Main Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Firmware File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Backup/Restore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Station List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Chapter 10. Telnet Commands
Remote Terminal Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

eco PDU PG Series User Manual
14
Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Session Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Read Power Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Switch Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Read Environmental Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Close Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Reboot PDU Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Reset All PDU Config to Default Value . . . . . . . . . . . . . . . . . . . . . . . 100
Appendix
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
The eco PDU’s Main Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Securing the Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Resetting the Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Recovery Procedure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
IP Address Determination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Method 1: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Method : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Method 3: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
PG95 30B / PG95 30B / PG95 30G. . . . . . . . . . . . . . . . . . . . . . . 110
PG95330B / PG95330B / PG95330G. . . . . . . . . . . . . . . . . . . . . . . 111
PG96 30B / PG96 30B / PG96 30G. . . . . . . . . . . . . . . . . . . . . . . 113
PG96330B / PG96330B / PG96330G. . . . . . . . . . . . . . . . . . . . . . . 114
PG98 30B / PG98 30B / PG98 30G. . . . . . . . . . . . . . . . . . . . . . . 116
PG98330B / PG98330B / PG98330G. . . . . . . . . . . . . . . . . . . . . . . 117
Administrator Login Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0

eco PDU PE Series User Manual
15
About This Manual
This manual is provided to help you get the most out of your eco PDU. It covers
all aspects of the power distribution unit, including installation, configuration,
and operation. An overview of the information found in the manual is provided
below.
Chapter 1, Introduction , introduces you to the unit/system. It presents
purpose, features and benefits are presented, and its front and back panel
components are described.
Chapter 2, Hardware Setup, provides step-by-step instructions for setting
up your installation, and explains some basic operation procedures.
Chapter 3, Basic Operation and First-Time Setup, explains the
procedures that the administrator employs to set up the eco PDU network
environment, and change the default username and password.
Chapter 4, Logging In, describes how to log in to the eco PDU with an
Internet browser, and explains the layout and components of the user interface.
Chapter 5, Energy, describes how to monitor and configure the eco PDU
energy settings.
Chapter 6, ser Management, describes how to configure the eco PDU
user management such as username and password.
Chapter 7, Log, describes how to read and export log from the eco PDU.
Chapter 8, Setup, describes how to configure and manage the eco PDU as a
whole.
Chapter 9, PD , describes how to perform a firmware upgrade on the eco
PDU, or back up and restore files.
Chapter 10, Telnet Commands, describes how to connect to and access the
eco PDU’s using Telnet.
Appendix, at the end of the manual provides technical and troubleshooting
information.
Note:
ead this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit and/or connected
devices.

eco PDU PG Series User Manual
16
The product may be updated, with features and functions added, improved,
or removed since the release of this manual. For an up-to-date user
manual, visit http://www.aten.com/global/en/.
Conventions
This manual uses the following conventions:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means
to press the Enter key. If keys need to be chorded, they
appear together in the same bracket with a plus sign
between them: [Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential
steps.
>Indicates selecting consecutive options (such as on a menu
or dialog box). For example, Start > Run means to open the
Start menu, and then select Run.
Indicates critical information.

17
Chapter 1
Introduction
Overview
ATEN PG95 / PG96 / PG98 3-Phase 30-Outlet 0U PDU series ships with 6 x
IEC 60320 C19 and 24 x IEC 60320 C13 outlets along with a 0U rack
enclosure. Containing an A M Cortex-A8 processor, the PG95 / PG96 / PG98
series delivers flexible control methods through its LAN / COM / USB /
environmental sensor ports, while being able to power up all connected
equipment in less than 10 seconds once plugged in. For cost-saving and space-
efficient setup purposes, the PG95 / PG96 / PG98 series can be cascaded to
connect up to 64 PDU units. As a result, these PDUs accommodate the
increasing demand for power to high-density IT devices in server rooms and
data centers.
In terms of hardware design, these PDUs have built-in energy-saving relays, a
subtype of electromagnetic switch, to help operators control large amounts of
current flow, which results in lower energy consumption compared to relay
models incapable of energy saving.
Other highlights include the circuit breaker preinstalled onto the PG95330 /
PG96330 / PG98330 models that support 30A / 32A current flow, which
automatically switches off electricity supply to protect devices from overload
or damage. With five colors (yellow, red, purple, blue, and green) of LCD
console panel stickers available for users to choose from, differentiating
between power feed settings and speeding up troubleshooting are made easier.
Plus, the LCD console panel is hot-swappable and can be removed, replaced,
or repaired without powering down a mission-critical connected load.
Ideal for enterprise servers, network closets, and data centers, the PG95 / PG96
/ PG98 series is an intelligent power distribution and management solution that
supports high-density IT applications while minimizing the overall cost.

eco PDU PG Series User Manual
18
eatures
A M Cortex-A8 processor for flexible control methods via LAN / COM /
USB / environmental sensor ports and enhanced monitoring via LCD
console
Advantageous hardware / network specifications
1 Gbps Ethernet Interface
Auto Ping & eboot
emote Management Protocols: TCP/IP, UDP, HTTP, HTTPS, SSL,
DHCP, SMTP, A P, NTP, DNS, Auto Sense, Ping, SNMP
V1&V2&V3, Telnet, Modbus (over TCP/IP), Wi-Fi, 802.11 a/b/g/n
network protocols, IPv6, and SMS
Alerts / Alarms: receives alarms via SNMP, SMTP, SMS
1
, and syslog
Scripting: JSON- PC ( emote Procedure Call) protocol and Python
scripting to control specified PDU unit (e.g. Switch On / Off)
1
Security: 2-level account / password login access, and IP / MAC filter,
TLS 1.2, SMTP / SMTPS protocols
Authentication: LDAP, ADIUS, TACACS+
Expandable installation
Allows for connecting up to 64 PDU units with cascading
Up to 16 PDU units can be daisy chained via LAN port connection and
PON port connection to ATEN’s KN series KVM over IP Switches
2
Energy-efficient relays allow operators to control large amounts of
current flow for lower energy consumption
Precise kWh metering (+/-1%) for better power consumption habits,
baselines, and initiative tracking
Environmental sensor port enables J-45 connectivity to connect or
daisy-chain up to 8 environmental sensors for monitoring and
management of temperature, humidity, airflow, differential air
pressure, and leaks
3
eal-time LCD Alert sends warnings to alert users of unusual power
state
An adjustable power cord is built in to the unit cable of 90-degree
rotation to allow flexible in-rack installation, resulting in better cable
organization

Chapter 1. Introduction
19
Secure locking enhancement prevents power cords from becoming
unplugged due to vibration or human error
Supports ATEN’s eco DC (Energy & DCIM Management Web GUI)
for monitoring power distribution, energy, and environmental data
from PDUs and connected devices
Note: 1. To be included in a future firmware release.
2. Firmware upgrade of the KN series is required.
3. Please contact the local sales representative for further information on
the environmental sensor.
Proactive Overload Protection (POP)
The PG96 and PG98 series models feature ATEN's exclusive Proactive
Overload Protection (POP) technology. Effective on all non-critical outlets,
this added safety feature automatically powers off outlets when a current
overload occurs.
POP mode is engaged, powering off the outlets, when the current exceeds the
maximum threshold value set. The LED display shows POP and a beeper
sounds. Press any button for two seconds to clear POP mode and power the
outlets back on.
Note: PG95 series doesn't support POP function.

eco PDU PG Series User Manual
0
Requirements
Browsers accessing the eco PDU must support TLS 1.0.
For cold booting of attached computers, the computer's BIOS must
support Wake on LAN or System after AC Back.
For Safe Shutdown:
The computer must be running Windows (2000 or above) or Linux.
The Safe Shutdown program — PMonitor — must be installed and
running on the computer (available by download from our website).
Note:
Safe shutdown program PMonitor can be downloaded from the
Support and Download section of the product web page, as shown
below
Cable Holders
Cable holders are optional accessories. For added safety, use ATEN Lok-U-
Plug cable holders to secure the cables from your attached devices in place on
the eco PDU. Only the ATEN Lok-U-Plug cable holders that have been
specifically designed to work with the eco PDU can be used. Using any other
kinds of cable securing device could potentially result in irreversible damage
or harm to the device or users. For a list of compatible cable holders, please
refer to the Compatible Products section on the product web page.

Chapter 1. Introduction
1
Components
ront View
No. Item Description
1 power outlets* 30 in total ( 4 x IEC 603 0 C13 + 6 x IEC 603 0
C19)
Bank 1-1: Outlet 1–10: 8 x C13; x C19
Bank 1- : Outlet 11– 0: 8 x C13; x C19
Bank 1-3: Outlet 1–30: 8 x C13; x C19
status panel The status panel contains:
 USB Type-A port
 COM + PON port
 Readout Section and LEDs
 Environmental Sensor Port
 LAN Ports
 Reset Switch
Full details of this section are provided on
page .
PG95230 / PG96230 / PG98230
PG95330B / PG95330B2 / PG96330B / PG96330B2 / PG98330B / PG98330B2
PG95330G / PG96330G / PG98330G
5
14
5
1
5
12
5
14
5
1
5
123 3 3
5
14
5
1
5
123 3 3

eco PDU PG Series User Manual
Note: Holes for ATEN Lok-U-Plug cable holders are located around the
outlets. See Securing the Cables, page 30, for further information.
Status Panel
3 circuit breaker (not
applicable to PG95 30 /
PG96 30 / PG98 30
series)
As a safety measure, if there is an overcurrent
situation in regards to the device’s power, the
circuit breakers will trip. Press the button to
recover normal operation.
Warning: See Resetting the Circuit Breaker,
page 106 for important information about resetting
a tripped circuit breaker.
4 power cord Connects the unit to an AC power source.
5 outlet status LEDs
(not applicable to PG95
series)
These LEDs indicate outlet status.
Lights green for powered on.
Off for powered off.
No. Item Description
1 USB Type-A
port
(firmware
upgrade /
log export)
Connects to a USB Type-A storage device for firmware upgrade
or log export.
 USB firmware upgrade:
The eco PDUs support quickly firmware upgrade through
USB port.
 USB setting & log file restored:
Users can export the setting and the log file through USB.
COM + PON
port
 COM: Connects to a hardware or software controller for
remote control.
 PON: Connects to KN series for cascading up to 16 PG
PDUs.
3 LAN 1 (10/
100/1000M)
The cable that connects the unit to the Internet, LAN, WAN, or to
cascade up to 64 PG PDUs plugs in here.
No. Item Description
5 6 7

Chapter 1. Introduction
3
4 reset button This button is recessed and must be pushed with a thin object,
such as the end of a paper clip.
 Press and release to reboot the device.
 Press and hold for more than three seconds to reset the eco
PDU back to its factory default settings.
5 sensor port This RJ-45 port is currently reserved for future expansion.
6 LAN (10/
100M)
The cable that connects the unit to the Internet, LAN, WAN, or to
cascade up to 64 PG PDUs plugs in here.
7 readout
section
 When PDU / Phase / Bank / Outlet is selected, readouts for its
current, voltage, power, and IP address appear in the display
window.
 Press the button next to the LCD display window to cycle the
selection between the items; the LCDs next to the items
indicate which one is currently displayed.
 When a sensor is selected, the display displays temperature /
humidity / differential pressure according to the sensor type
No. Item Description

eco PDU PG Series User Manual
4
This Page Intentionally Left Blank