ATIM VULCANO TABLE 411/78 0504 User manual

ASSEMBLY INSTRUCTIONS VULCANO TABLE
CODICE ATIM: 411/78.
.0504.xx mm 1600x800
.0505.xx mm 1600x900
.0506.xx mm 1900x900
rev. 1.0
16/06/08
For any suggestions or feedback: [e-mail]
PAGE 1/2
Assembly Instructions for VULCANO table _ 411-78.05xx.xx.doc
1
2
Accessories bag contents:
32 x Galvanized TCCE M6 x 85 screw cod. 2.6510951.02
32 x Galvanized washer mm 12 x 2 hole 6.3 cod. 2.653041.02
24 x Nickel-plated TPS M6 x 16 CE screw cod. 2.652941.06
8 x TCCE zinc-plated screw M8 x 15
ISO 4762 cod. 2.652931.02
8 x Washer mm 16x1.5 hole 8.5 zinc. cod. 2.650141.02
8 x Leg cap 60x60 cod. 2.207085.xx
4 x White adhesive felt pad 35 x 35 x 3 cod. 2.653467.01
4 x Bumper D. 12x12.8 PF3 T. flat cod. 2.553077.13
1 x Galvanized hex key n ° 4 cod. 2.553061.02
1 x Galvanized hex key n ° 5 cod. 2.5512481.02
Box Content:
4 x Leg mm 714 P.A014 cod. 3.2016165.xx
8 x Joint mm 75 P. AA0079 gr. cod. 3.2015965.01
2 x Beam mm 676 P.A014
mm 1600x800:
cod. 3.2016155.xx
mm 1600x900 e
mm 1900x900:
cod. 3.2016285.xx
2 x Current + mounted guide
mm 1600x800 e
mm 1600x 900:
cod. 3.2016145.xx
mm 1900x900:
cod. 3.2016765.xx
1 x Set of 2 glasses + 1 extension
mm 1600x800:
cod. 2.9116173.xx
mm 1600x900:
cod. 2.9116183.xx
mm 1900x900:
cod. 2.9116193.xx
Place 2 joints in correspondence with the holes on the leg
and assemble them as shown in figure 1, making sure that
the other 2 holes on the joint face inwards.
Fix the joints to the leg using 4 TCCE M6 x 85 screws and 4
washers 12 x 2 mm hole 6.3 per joint.
Repeat the same operation on all 4 legs.
Joint leg
Joint
Leg
Align the legs with joints to the crosspiece and
assemble the 2 leg bridges as in figure 2. Only
then assemble the two leg bridges with the
currents, keeping the guides facing inwards.
Secure with TPS M6 x 16 CE screws.
Beam
Galvanized washer
mm 12 x 2 hole 6.3
Galvanized TCCE
M6 x 85 screw
4 x
4 x
Current + guide
TPS M6 x 16 Screw
Full leg bridge

ASSEMBLY INSTRUCTIONS VULCANO TABLE
CODICE ATIM: 411/78.
.0504.xx mm 1600x800
.0505.xx mm 1600x900
.0506.xx mm 1900x900
rev. 1.0
16/06/08
For any suggestions or feedback: [e-mail]
PAGE 2/2
Assembly Instructions for VULCANO table _ 411-78.05xx.xx.doc
Place the glass half-tops, taking care to align the pads
with the respective holes on the brackets. Screw each
top with 4 TCCE M8 screws and 4 washers 16 x 1.5 mm.
Insert the 8 caps at the ends of each of the 4 legs, glue the
felt pads on the lower caps and on the 2 crosspieces in the
position shown in figure 3.
Cap
3
5
Felt Pad
3a
Cam
Pay attention to the position of the cam, the
correct position is rotated as in figure 3a.
Opening (1,2) and closing (3,4,5) the table.
1
2
3
4
5
Flat locking knob (1 per side).
Unscrew before moving the tops.
Backing pad
Bracket
First place the extension
by inserting it into the
appropriate support as
shown in figure 4, then
the two half-
planes as
shown in figure 5.
4
Side with
rubber
TCCE M8 x 15 Screw
Washer mm 16 x 1.5