Atlona OmniStream AT-OMNI-512 User manual

1
Installation Guide
AT-OMNI-512
OmniStream R-Type Dual-Channel Networked AV Encoder
AT-OMNI-512
The Atlona OmniStream™ R-Type (AT-OMNI-512) is a networked AV encoder with two
independent channels of encoding for two HDMI sources up to UHD @ 60 Hz and HDR, plus
embedded audio and RS-232 or IR control pass-through. It is part of the OmniStream R-Type
Series, designed for high performance, exible distribution of AV over Gigabit Ethernet in
residential and light commercial applications. The OmniStream 512 is HDCP 2.2 compliant
and ideal for the latest as well as emerging UHD and HDR sources. It features visually lossless
compression with pristine-quality video and graphics performance, plus extremely low, sub-
frame latency from encode to decode – critical for demanding applications such as gaming.
This dual-channel encoder is housed in a half-width rack enclosure and is ideal for high-density,
compact installation in a centralized equipment location.
IMPORTANT: Visit http://www.atlona.com/product/AT-OMNI-512 for the latest
rmware updates and User Manual.
1 x AT-OMNI-512
1 x Push spring connector, 6-pin
1 x Wall/table mounting brackets
4 x Rubber feet
1 x Installation Guide
• OmniStream R-Type uses mDNS as the discovery mechanism. In order for mDNS to
function properly, there must not be restrictions applied to the network.
Package Contents
Operating Notes

2
Installation Guide
AT-OMNI-512
HDMI
PWR LINK
TM
O MNI S TREAM
ID
1 2 1 2
R - T YPE
AT-OMNI-512
ETHERNET
RS-232 / IR
DC 48V
RX TX
1
2
HDMI IN
2
121
HDMI
PWR LINK
TM
O MNI S TREAM
ID
1 2 1 2
R - T YPE
AT-OMNI-512
ETHERNET
RS-232 / IR
DC 48V
RX TX
1
2
HDMI IN
2
121
1 PWR
This LED indicator is green when the unit
is powered.
2 HDMI 1 / HDMI 2
These LED indicators show the active
input status.
3 LINK 1 / LINK 2
These LED indicators show the link status
of the encoder.
4 ID
Press this button to identify the unit within
the AMS software.
5 REBOOT
Use a pointed object to press this
recessed button and reboot the unit.
6 HDMI 1 / HDMI 2
Connect HDMI cables from these ports to
UHD/HD sources.
7 ETHERNET 1 / ETHERNET 2
Connect Ethernet cables from these ports
to the Local Area Network (LAN).
8 RS-232 / IR
Use the included captive screw connector
to connect an automation system and
an IR emitter or extender. Refer to RS-
232 and IR, on the next page for more
information.
9 DC 48V
Connect the optional 48V DC power
supply to this power receptacle. This
power supply is available, separately.
Panel Descriptions
1 2 3 4 5
876 9

3
Installation Guide
AT-OMNI-512
The AT-OMNI-512 provides RS-232 over IP which allows communication between an automation
system and an RS-232 device. This step is optional. Either the top three or bottom three set of
terminals can be used for RS-232.
1. Use wire strippers to remove a portion of the cable jacket.
2. Remove at least 3/16” (5 mm) from the insulation of the RX, TX, and GND wires.
3. Insert the TX, RX, and GND wires into correct terminal on the included push spring
connector, following the wiring diagram below. If using non-tinned stranded wire, press the
orange tab, above the terminal, while inserting the exposed wire.
The same port that provides RS-232 connections also supports either an IR extender or IR
emitter. This step is optional. Either the top three or bottom three set of terminals can be used
for RS-232.
1. Use wire strippers to remove a portion of the cable jacket.
2. Remove at least 3/16” (5 mm) from the insulation from each of the two wires.
3. Insert the wires into the correct terminal on the included push spring connector, following
the desired wiring diagram below.
NOTE: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for ground.
On some devices, the function of pins 2 and 3 are reversed.
Push tab
to unlock
GND
RX
TX
RS-232
IR
IMPORTANT: The IR emitter must be placed no more than 1” from the IR
sensor on the device, in order to function properly.
IR extender congurationIR emitter conguration
GND (black)
IR emitter
SIGNAL (white/black)
RX TX GND
GND (black)
SIGNAL (white/black)
Control
Unit
TX out
GND
RX TX GND

4
Installation Guide
AT-OMNI-512
HDMI
PWR LINK
TM
OMNISTREAM
ID
1 2 1 2
R-TYPE
AT-OMNI-512
ETHERNET
RS-232 / IR
DC 48V
RX TX
1
2
HDMI IN
2
121
PWR indicator
1. Connect an Ethernet cable from the ETHERNET 1 and ETHERNET 2 ports on the encoder
to a PoE-capable switch on the Local Area Network (LAN). Note that if a PoE-capable
switch is not available, the 48V DC power supply (sold separately) must be connected to the
encoder.
2. Connect an HDMI cable from each HD/Ultra HD source to the HDMI 1 and HDMI 2 ports on
the encoder.
3. If using RS-232 and/or IR, connect the 6-pin captive screw connector to the RS-232 / IR
port on the encoder.
4. The PWR indicator, on the front panel, displays the power status of the encoder. When the
encoder is powered, using either PoE or the optional 48V DC power supply (not included),
the LED initially turns red. After a few moments it will turn amber, and nally green.
The AT-OMNI-512 is shipped in DHCP mode. If a DHCP server is not found within 60 seconds,
the unit will automatically be placed in Auto IP mode and will be assigned an IP address within
the range 169.254.xxx.xxx. If this occurs, a static IP address can be assigned to the encoder,
allowing it to be access on the network.
1. Disconnect the AT-OMNI-512 from the network.
2. Make sure that the encoder is powered. Power will need to be supplied either by the
external 48V power supply (not included) or by connecting an Ethernet cable, from either
ETHERNET 1 or ETHERNET 2,to a PoE-capable switch.
3. Connect an Ethernet cable from the PC, to the other unused ETHERNET port on the
encoder.
4. Click Start > Settings > Control Panel > Network and Sharing Center.
5. Click Change adapter settings.
6. Right-click on the adapter that is used to establish a wired connection to the network, and
select Properties from the context menu.
7. Under the Ethernet Properties dialog box, select Internet Protocol Version 4 and then
click the Properties button.
8. Click the Use the following IP address radio button.
Installation
IP Conguration
IMPORTANT: Before continuing, write down the current IP settings in order to
restore them, later. If Obtain an IP address automatically and Obtain DNS server
automatically are selected, then this step is not required.

5
Installation Guide
AT-OMNI-512
9. Enter the desired static IP address or the IP address provided by the network administrator.
If the PC does not require Internet access or if a statically-assigned IP address is being
used, then an IP address of 169.254.xxx.xxx can be entered.
10. Set the subnet mask to 255.255.0.0.
11. Click the OK button then close all Control Panel windows.
12. Reconnect the AT-OMNI-512 to the network.
Connection Diagram
AT-OMNI-512
ETHERNET
RS-232 / IR
DC 48V
RX TX
1
2
HDMI IN 2
121
Video
Ethernet
Video
Video
Control
Ethernet
Ethernet
Ethernet
Ethernet
OmniStream 512
Encoder
OmniStream 521
Decoder
Projector
to additional
OmniStream 521
Decoders
Network
Switch
Media
Player
Set-Top Box
Eth 1 Eth 2
HDMI 1 HDMI 2
4
media4
OK
224
TM
O
MNI
S
TREAM
LINKPWR
R
-
T
YPE

6
Installation Guide
AT-OMNI-512
The AT-OMNI-512 encoder includes two
mounting brackets and four mounting screws,
which can be used to attach the unit to any at
surface.
1. Using a small Phillips screwdriver, remove
the two screws from the left side of the
enclosure.
2. Position one of the mounting brackets, as
shown below, aligning the holes on the
side of the enclosure with one set of holes
on the mounting bracket.
3. Use the enclosure screws to secure the
mounting bracket to the enclosure.
4. To provide added stability to the mounting
bracket, use two of the included screws
and attach them to the two holes, directly
below the enclosure screws, as shown
above.
5. Repeat steps 1 through 4 to attach the
second mounting bracket to the opposite
side of the unit.
6. Mount the unit using the oval-shaped
holes, on each mounting bracket. If using
a drywall surface, a #6 drywall screw is
recommended.
HDMI
PWR LINK
TM
O
MNI
S
TREAM
ID
1 2 1 2
R
-
T
YPE
HDMI
PWR LINK
TM
O
MNI
S
TREAM
ID
1 2 1 2
R
-
T
YPE
HDMI
PWR
LINK
TM
O
MNI
S
TREAM
ID
1
2 1 2
R
-
T
YPE
Included screws
NOTE: Mounting brackets can
also be inverted to mount the
unit under a table or other at
surface.
Mounting Instructions

7
Installation Guide
AT-OMNI-512
Troubleshooting
Problem Solution
PWR indicator is o. • If using a PoE switch, make sure that the port on the
switch that is connected to the encoder, has PoE
enabled. When the encoder is powered using PoE, the
PWR indicator will be green.
• Check the Ethernet cable for possible damage or loose
connections.
• Connect the optional 48V DC power supply (available
from atlona.com) to the encoder. When using an external
power supply, the PWR indicator will be red.
LINK indicator is red. • The optional 48V DC power supply is connected, but no
Ethernet cables are connected between the switch and
the ETHERNET port(s).
• Check the Ethernet cable for possible damage or loose
connections.

8
Installation Guide
AT-OMNI-512
© 2017 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Version 1
atlona.com •408.962.0515 •877.536.3976