Atlona AT-LINE-PRO4 User manual

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515
User Manual
AtlonA
10 Inputs Professional
Video Processor
AT-LINE-PRO4

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 2
TABLE OF CONTENTS
1. Introduction .................................................. 3
2. Package Contents .................................................. 3
3. Features .................................................. 3
4. Specication .................................................. 4
5. Operation Controls and Functions .................................................. 4
5.1. Front Panel .................................................. 4
5.2. Rear Panel .................................................. 5
6. Remote Control .................................................. 5
7. On-Screen-Display .................................................. 6
8. Connection and Installation .................................................. 7
9. RS232 Control .................................................. 8
9.1. Set Command .................................................. 8
9.2. Status Command .................................................. 10
9.3. Key Command .................................................. 11
10. Safety Information .................................................. 12
11. Warranty .................................................. 13
12. Atlona Product Registration .................................................. 14

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 3
INTRODUCTION
PACKAGE CONTENTS:
The Atlona AT-LINE-PRO4 is a professional quality 10-input video scaler/processor that allows four
HDMI or DVI, three VGA, one component, one S-Video and one composite video input to be scaled to
a single HDMI output. The LINE-PRO4 also gives you the exibility to add PAL or NTSC that may not
be native to your display. The onscreen display gives you the ability to change audio options, scaling
options, resolution switching and much much more. With additional functions as RS232 and IR the AT-
LINE-PRO4 is easier than ever to control or integrate with preexisting system.
• 10-Input Professional Video Scaler
• 5V/2.6A DC power adaptor
• Operations manual
FEATURES:
• Scaling any incoming Signal whether VGA, Composite, DVI or any other to the native resolution of the
display: VGA~WUXGA or 480p~1080p
• Analog to digital AV conversion
• PAL to NTSC and NTSC to PAL conversion 50/60Hz
• Digital and analog switching capabilities with HDMI out
• RS232 commands available for control systems
• Digital coax out for connecting your audio to an AV receiver
• Learnable IR codes for universal remote controls
• Standard 1U size for easy rack mounting
• 3.5mm Audio jacks for audio embedding on HDMI inputs (the main purchase for that is DVI sources
are used with HDMI/DVI adapters)
• Full 3D support on HMDI pass through
• Horizontal and vertical shift, color, tint, brightness, contrast, detail, sizing, and top and bottom vertical
blanking adjustments
• HDMI 1.3c, HDCP 1.1 and DVI 1.0 compliant
• VGA Inputs Supports following Resolutions: VGA ~WUXGA or 480p~1080p
• HDMI inputs support following resolutions: 480i~1080p and VGA~WUXGA
• Supports deep color of 8 / 10 / 12 bits per color (x3)
• On-Screen-Display allows users to fully adjust inputs/outputs preferences
• 3-D motion adaptive & 3-D video noise reduction

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 4
SPECIFICATIONS:
OPERATION CONTROLS AND FUNCTIONS
Input Ports 4 x HDMI (DVI), 3 x VGA, 1xS-Video, 1 x Component Video,
1 x Composite Video
Output Ports 1 x HDMI, 1xCoaxial
HDMI Resolutions 480i~ 1080p60 and VGA~WUXGA
PC Resolutions VGA ~WUXGA, 480p~1080p60
ESD Protection Human body model: ± 8kV (air-gap discharge)
± 4kV (contact discharge)
Power Supply 5V/2.6A DC (US/EU standards, CE/FCC/UL certied)
Dimensions (inch) 17.1 (W) x 6.57 (D) x 1.92 (H)
Weight (lb) 4.7
Power Consumption 8.5W
Operating Temperature 0°C ~ 40°C / 32°F~104°F
Storage Temperature -20 C ~60 C / -4°F~140°F
Relative Humidity 20~90% RH (non-condensing)
5.1. Front Panel
1. POWER BUTTON AND LED: Press this button to turn on or set the device to standby mode. The LED will
illuminate red when the power is on.
2. IR RECEIVER: This IR window receives IR signal from the remote control included in the package.
3. CV BUTTON AND LED: Press this button to select the composite video input source and the LED will
illuminate in red.
4. SV BUTTON AND LED: Press this button to select the s-video input source and the LED will illuminate in red
5. COMP: Press this button to select the component video input source and the LED will illuminate in red.
6. VGA 1~3 BUTTONS AND LED: Press VGA 1/VGA 2/VGA 3’s button to select the VGA 1/VGA 2/VGA 3 input
source and the LED will illuminate in red.
7. HDMI 1~4 BUTTONS AND LED: Press HDMI 1/HDMI 2/HDMI 3/HDMI 4 button to select the HDMI 1/HDMI 2/
HDMI 3/HDMI4 inputs source and the LED will illuminate in red
8. MENU: Press this button to bring up the On-Screen-Display selection.
9. -/+: Press -/+ buttons for OSD selection bar of down/up. Once the selection is made press “enter” button.
10. ENTER: Press this button after each selection.

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 5
5.2. Rear Panel
1. RS-232: This port is to connect to a PC for rmware updates or a control system.
2. HDMI OUT: This port is to connect to HD Display or Projector for displaying the output signal. The DVI/HDMI
adapter can be used if the display has DVI input.
3. COAX OUT: This port is to send audio signal to a separate AV Receiver. The audio will still be present on the
HDMI Output.
4. HDMI IN 1~4 & L/R: These ports are to connect input sources such as Blu-ray players, Cable Boxes,
Computers with HDMI or DVI outputs. If user has a DVI source, the 3.5mm audio input will allow to embed
audio.
5. VGA IN 1~3 & L/R: These ports are used to connect to Computers or any other sources with VGA ports to
LINE-PRO4, while 3.5mm stereo audio inputs are used to embed audio.
6. Y/HD, CR/PB, CB/PB & L/R: These ports are to connect component video sources.
7. COAX: This port is to embed digital audio signal from any source.
8. SV & L/R: These ports are to connect S-Video source.
9. CV & L/R: These ports are to connect to composite source.
10. DC 5V
REMOTE CONTROL
• POWER: Press the button to power ON the LINE-PRO4. Press again to enter
into standby mode.
• INPUT: Press the button repeatedly to cycle through the various input sources.
Or use separate buttons for exact input selections.
• CV INPUT: Press this button to select Composite Video input directly.
• PC1, 2, 3 INPUTS: Press these buttons to select VGA 1, VGA 2, VGA 3 inputs.
• HDMI 1, HDMI 2, HDMI 3, HDMI 4 INPUTS: Press these buttons to select
HDMI 1, HDMI 2, HDMI 3, HDMI 4 inputs.
• OUTPUT RESOLUTION: Press any one of the buttons to select the output
resolution. For other output resolutions that are not covered by these buttons,
please enter into On-Screen-Display menu to select.
• MENU: Press this button to bring up On-Screen-Display main menu page.
• EXIT: Press this button to exit from a menu.
• UP/DOWN/LEFT/RIGHT: Press the Up/Down buttons to move the highlighted
bar to your desired parameter during the On-Screen-Display operation. Press
the Left/ Right buttons to increase/decrease the setting value of a selected
parameter.
• OK (Enter): Press this button to conrm your selection.
• RESET: Press this button to reset the unit’s settings to the factory default value.
• AUTO ADJUST: Press this button to optimize the position of the picture (picture
centering) on the screen.

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 6
1st Tier Option 2nd Tier Option Adjustment
VIDEO - PICTURE MODE USER / STANDARD / VIVID / MOVIE
- CONTRAST 0 ~ 100 of Contrast Level
- BRIGHTNESS 0 ~ 100 of Brightness Level
- HUE 0 ~ 100 of Hue Leve
- SATURATION 0 ~ 100 of Saturation Level
- SHARPNESS 0 ~ 100 of Sharpness Level
- SCALE OVERSCAN / UNDERSCAN / LETTERBOX
/PANSCAN / FULL
- NR LOW / MIDDLE / HIGH / OFF
- EXIT Back to the 1st Tier
COLOR - COLOR TONE USER / NORMAL / WARM / COOL
- RED 0 ~ 100 of Red Color Level
- GREEN 0 ~ 100 of Green Color Level
- BLUE 0 ~ 100 of Blue Color Level
- EXIT Back to the 1st Tier
OUTPUT - NATIVE / VGA / SVGA / XGA / SXGA/UXGA / 480i
/ 480p / 720p@60Hz /1080i@60Hz / 1080p@60Hz
/ 576i / 576p/ 720p@50Hz / 1080i@50Hz /
1080p@50 / WXGA / WSXGA / WUXGA
OSD - HPOSITION 0 ~ 100 of OSD Horizontal Position
- VPOSITION 0 ~ 100 of OSD Vertical Position
- TIMER 0 ~ 100 of OSD Show Time (sec.)
- TRANSP 0 ~ 100 of OSD Transparent Level
- EXIT Back to the 1st Tier
AUDIO - SOURCE HDMI / L/R / COAXIAL
- DELAY OFF / 40MS / 110MS / 150 MS
- SOUND ON / MUTE
- EXIT Back to the 1st Tier
INFORMATION - SOURCE (Input interface)
INPUT (Input Resolution)
OUTPUT (Output Resolution)
VERSION (Firmware Version)
EXIT - Close the OSD Menu
ON-SCREEN-DISPLAY

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 7
CONNECTION AND INSTALLATION
Blu-ray
Blu-ray
DVD
DVD
STB
VCR
PC
Notebook
or
HDTV
Amplier

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 8
AT-LINE-PRO4 Remote Controller
PIN Denition PIN Denition
1 NC 1 NC
2TxD 2RxD
3RxD g3TxD
4 NC 4 NC
5 GND f5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
RS-232 transmission format:
Baud Rate: 19200 bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1 Bit
Flow Control: None
9.1. Set Command:
Command Code Response Description
S POWER 0 >POWER OFF SET POWER OFF
S POWER 1 >POWER ON SET POWER ON
S SOURCE 0 >SOURCE CV SET SOURCE CV
S SOURCE 1 > SOURCE SV SET SOURCE SV
S SOURCE 2 > SOURCE COMP SET SOURCE COMP
S SOURCE 3 > SOURCE PC1 SET SOURCE PC1
S SOURCE 4 > SOURCE PC2 SET SOURCE PC2
S SOURCE 5 > SOURCE PC3 SET SOURCE PC3
S SOURCE 6 > SOURCE HDMI1 SET SOURCE HDMI1
S SOURCE 7 > SOURCE HDMI2 SET SOURCE HDMI2
S SOURCE 8 > SOURCE HDMI3 SET SOURCE HDMI3
S SOURCE 9 > SOURCE HDMI4 SET SOURCE HDMI4
S OUTPUT 0 > OUTPUT NATIVE OUTPUT EDID NATIVE MODE
S OUTPUT 1 > OUTPUT VGA VGA(640X480@60) OUTPUT
S OUTPUT 2 > OUTPUT SVGA SVGA(800X600@60) OUTPUT
S OUTPUT 3 > OUTPUT XGA XGA(1024X768@60)) OUTPUT
S OUTPUT 4 > OUTPUT SXGA SXGA(1280X1024@60) OUTPUT
S OUTPUT 5 > OUTPUT UXGA UXGA(1600X1200@60) OUTPUT
S OUTPUT 6 > OUTPUT 480i 480i OUTPUT
RS232 CONTROL

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 9
S OUTPUT 7 > OUTPUT 480p 480p OUTPUT
S OUTPUT 8 > OUTPUT 720p 720p@60 OUTPUT
S OUTPUT 9 > OUTPUT 1080i 1080i@60 OUTPUT
S OUTPUT 10 > OUTPUT 1080p 1080p@60 OUTPUT
S OUTPUT 11 > OUTPUT 576i 576i@60 OUTPUT
S OUTPUT 12 > OUTPUT 576p 576p@60 OUTPUT
S OUTPUT 13 > OUTPUT 720p 720p@50 OUTPUT
S OUTPUT 14 > OUTPUT 1080i50 1080i@50 OUTPUT
S OUTPUT 15 > OUTPUT 1080p50 1080p@50 OUTPUT
S OUTPUT 16 > OUTPUT WXGA WXGA (1280x800@60) OUTPUT
S OUTPUT 17 > OUTPUT WSXGA WSXGA (1680x1050@60) OUTPUT
S OUTPUT 18 > OUTPUT WUXGA WUXGA (1920X1200@60) OUTPUT
S OUTPUT 19 > OUTPUT WXGA+ WXGA+(1440X900@60) OUTPUT
S OUTPUT 20 > OUTPUT SXGA+ SXGA+ (1400X1050@60) OUTPUT
S SIZE 0 > SIZE FULL SCALER FULL OUTPUT
S SIZE 1 > SIZE OVERSCAN SCALER OVERSCAN OUTPUT
S SIZE 2 > SIZE UNDERSCAN SCALER UNDERSCAN OUTPUT
S SIZE 3 > SIZE LETTERBOX SCALER LETTERBOX OUTPUT
S SIZE 4 > SIZE PANSCAN SCALER PANSCAN OUTPUT
S PICTUREMODE 0 > PICTUREMODE STANDARD SET PICTUREMODE STANDARD
S PICTUREMODE 1 > PICTUREMODE MOVIE SET PICTUREMODE MOVIE
S PICTUREMODE 2 > PICTUREMODE VIVID SET PICTUREMODE VIVID
S PICTUREMODE 3 > PICTUREMODE USER SET PICTUREMODE USER
S CONTRAST 0~100 > CONTRAST 0~100 CONTRAST 0~100 ADJUST
S BRIGHTNESS 0~100 > BRIGHTNESS 0~100 BRIGHTNESS 0~100 ADJUST
S HUE 0~100 > HUE 0~100 HUE 0~100 ADJUST
S SATURATION 0~100 > SATURATION 0~100 SATURATION 0~100 ADJUST
S SHARPNESS 0~100 > SHARPNESS 0~100 SHARPNESS 0~100 ADJUST
S NR 0 >NR OFF SET NR MODE OFF
S NR 1 >NR LOW SET NR MODE LOW
S NR 2 >NR MIDDLE SET NR MODE MIDDLE
S NR 3 >NR HIGH SET NR MODE HIGH
S PCPHASE 0~63 > PCPHASE 0~63 PC MODE PHASE 0~63 ADJUST
S PCCLOCK 0~100 > PCCLOCK 0~100 PC MODE CLOCK 0~100 ADJUST
S PCHPOSITION 0~100 > PCHPOSITION 0~100 H POSITION 0~100 ADJUST
S PCVPOSITION 0~100 > PCVPOSITION 0~100 V POSITION 0~100 ADJUST
S COLORTEMP 0 >COLORTEMP NORMAL SET COLOR TEMPERATURE MODE NORMAL
S COLORTEMP 1 >COLORTEMP WARM SET COLOR TEMPERATURE MODE WARM
S COLORTEMP 2 >COLORTEMP COOL SET COLOR TEMPERATURE MODE COOL
S COLORTEMP 3 >COLORTEMP USER SET COLOR TEMPERATURE MODE USER
S RED 0~100 > RED 0~100 COLOR ”RED” ADJUST
S GREEN 0~100 > GREEN 0~100 COLOR “GREEN“ ADJUST
S BLUE 0~100 > BLUE 0~100 COLOR “BLUE“ ADJUST
S OSDHPOSITION 0~100 > OSDHPOSITION 0~100 OSD H POSITION 0~100 ADJUST

www.atlona.com | toll free: 1-877-536-3976
For International: 1-408-962-0515 10
S OSDVPOSITION 0~100 > OSDVPOSITION 0~100 OSD V POSITION 0~100 ADJUST
S OSDTIMEOUT 0~100 > OSDTIMEOUT 0~100 OSD TIMEOUT 0~100 SETTING
S OSDBACKGROUND
0~8
> OSDBACKGROUND 0~8 OSD BACKGROUND 0~8 ADJUST
S AUDIOMUTE 0 > AUDIOMUTE OFF AUDIO ACTIVE
S AUDIOMUTE 1 > AUDIOMUTE ON AUDIO MUTE
S AUDIODELAY 0 > AUDIODELAY OFF AUDIO DELAY OFF
S AUDIODELAY 1 > AUDIODELAY 40ms AUDIO DELAY 40mSec
S AUDIODELAY 2 > AUDIODELAY 110ms AUDIO DELAY 110mSec
S AUDIODELAY 3 > AUDIODELAY 150ms AUDIO DELAY 150mSec
9.2. Status Command:
Command Code Response Description
R POWER >POWER OFF~ON SHOW POWER STATUS
R SOURCE >SOURCE CV~HDMI4 SHOW SOURCE STATUS
R OUTPUT >OUTPUT NATIVE~SXGA+ SHOW OUTPUT STATUS
R SIZE >SIZE FULL~PANSCAN SHOW SIZE STATUS
R PICTUREMODE > PICTUREMODE
STANDARD~USER
SHOW PICTUREMODE STATUS
R CONTRAST > CONTRAST 0~100 SHOW CONTRAST VALUE
R BRIGHTNESS > BRIGHTNESS 0~100 SHOW BRIGHTNESS VALUE
R HUE > HUE 0~100 SHOW HUE VALUE
R SATURATION > SATURATION 0~100 SHOW SATURATION VALUE
R SHARPNESS > SHARPNESS 0~100 SHOW SHARPNESS VALUE
R NR > NR OFF~HIGH SHOW NR STATUS
R PCHPOSITION > PCHPOSITION 0~100 SHOW PC H-POSITION VALUE
R PCVPOSITION > PCVPOSITION 0~100 SHOW PC V-POSITION VALUE
R PCCLOCK > PCCLOCK 0~100 SHOW PC CLOCK VALUE
R PCPHASE > PCPHASE 0~63 SHOW PC PHASE VALUE
R COLORTEMP > COLORTEMP NORMAL~USER SHOW COLOR TEMP MODE
R RED > RED 0~100 SHOW COLOR RED VALUE
R GREEN > GREEN 0~100 SHOW COLOR GREEN VALUE
R BLUE > BLUE 0~100 SHOW COLOR BLUE VALUE
R OSDHPOSITION > OSDHPOSITION 0~100 SHOW OSD H-POSITION VALUE
R OSDVPOSITION > OSDVPOSITION 0~100 SHOW OSD V-POSITION VALUE
R OSDTIMEOUT > OSDTIMEOUT 0~100 SHOW OSD TIMEOUT VALUE
R OSDBACKGROUND > OSDBACKGROUND 0~8 SHOW OSD BACKGROUND STATUS
R AUDIOMUTE > AUDIOMUTE OFF~ON SHOW AUDIO MUTE STATUS
R AUDIODELAY > AUDIODELAY OFF~150ms SHOW AUDIO DELAY STATUS