Atmor New-3.0 User manual

INSTANT
WATER HEATER
1. Multi-pole switch
2. Terminal block
3. Thermostat
4. Microswitch
5. Switches
6. LED Light
7. Heating elements
8. Pressure switch
New/Lotus - 3.0 1.0;2.0 or 3.0kW 3.0 3.3 3.6 2.5mm216amps
New/Lotus - 3.5 1.5;2.0 or 3.5kW 3.2 3.5 3.8 2.5/4mm220amps
New/Lotus - 5.0 2.0;3.0 or 5.0kW 5.0 5.5 6.0 4/6mm225amps
New/Lotus - 5.5 2.5;3.0 or 5.5kW 5.5 6.0 6.6 4/6mm225-32amps
New/Lotus - 7.0 3.0;4.0 or 7.0kW 7.0 7.7 8.3 6/10mm240amps
New/Lotus - 8.0 4.0;4.0 or 8.0kW 7.3 8.0 8.7 6/10mm240amps
New/Lotus - 9.5 4.5;5.0 or 9.5kW 8.7 9.5 10.3 10mm245amps
Model Heat Setting kW loading Recommended
cable size
Recommended
fuse rating
220V 230V 240V
• Operating water pressure 0.3-7 BAR (5-100 psi) • Water pressure operating power switch
• Standard 1/2"Ø compression inlet connection • Top-left and right cable entry • Bottom-left water entry
UNIT DIMENSIONS: HEIGHT 185mm WIDTH 300mm DEPTH 110mm
Table 2
P.N: 116002B
L
N
230V
P
1 2 3 4 5 7
78
E
L2
L1
N
400V
P
1 2 3 4 5 7
78
E
230V
L
N
230V
P
1 2 3 4 5
6
7
78
E
6
6
Installation Instructions

Water
Outlet
Sink
Installation Instructions:
THE GUARANTEE IS SUBJECT TO CORRECT INSTALLATION.
The instant water heater is a novel appliance designed to supply hot water instantly while conserving
energy. When the pressure switch is on, then the heating element heats the flowing water.
General information
1. The appliance should be installed by a licensed electrician only.
2. It is recommended that a residual current device(ELCB)will be incorporated in the circuit.
3. Installation of water pipeline must be completed prior to the installation of the heater and must be
checked to assure that there are no water leaks.
4. This appliance requires water pressure of minimum 0.3 bar (4LB /IN). The appliance must be installed
horizontally where water supply comes from the left side.
5. WARNING! You must use only the supplied outlet accessories. The wateroutlet should always
be left open as the operating principle is based on an open wateroutlet.
6. Without supervision the use of the appliance by young children or infirm person is forbidden.
Playing with the unit by young children is forbidden.
Installation of sink& showerunit 3 kW- 9.5 kW
1. The shower unit should be installed above a person's height.(use installation chart)
2. Remove cover in order to connect the electric cable to the terminal block inside the unit.
(unscrew 4 screws)
3. The unit should have a separate electric cable in the switch board (see table 2)
4. The recommended electric cable for 2-Phase unit up to 9.5kWis 5 x 4.0mm2
5. A 110V/5kWdevice must be connected to a separate 40Afuse and a feeding cable of 3X6 mm2.
6. Check if there are no leaks as soon as the unit is connected.
Use the hoses supplied with the appliance, do not re-use old hoses
7. After connecting the water inlet to the unit, connect
the electric cable to the designed terminal blocks
including grounding.
WARNING! The appliance must be grounded
8. The unit must be connected to the electric supply by
a 2-pole switch (for one phase unit) and to the
multi-pole switch (in case of multi phase unit)
9. The main electric switch should be separated from
the unit.
10. Connect the electric cable with the designated clamp.
11. Return the cover (4 screws)
Summer
or
5kW & up
Winter
Jet Massage Spray Spray+Massage
4 Setting Spray
Fig. 2
Head Set 2
Sink
Rings Combination
Fig. 3
Foreffective use
1. Open the water faucet (before inlet) slowly until the lights in the rocker switch are "ON". Wait 15-20
seconds until hot water starts to flow. For colder water increase the water inflow gradually until you
receive the desired water temperature. For hotter water please decrease water inflow.
2. Heating position selector: 0 - Shut Off
1- Low (left light on)
2 - Medium (Right light on)
3 - High (both lights on)
3. In order to achieve maximum efficiency from the unit please grip the showerhead and twist it in either
direction, operating rings installed in showerhead can be changed according to season, summer or winter
position (Fig.1 & Fig.2). An additional ring set is supplied with the unit for head set 1 (Fig.1a).
For sink unit - Install open rings in summer and blind rings in winter (inner ring should remain always
open) (Fig.3).
4. The spray outlet should be cleaned periodically by unscrewing it from the showerhead and clean thoroughly.
(Fig.1a, Fig.2a, Fig.3)
5. The unit operates automatically by opening the water faucet and shut off when closing the water supply.
screws
screws
Inlet
Power
selections
screws
Power
selections
Inlet
screws
Water Inlet
Position
Selector
!!!Danger
Incorrect installation
Incorrect:
Danger: Do not
install a faucet at
the wateroutlet
Faucet
Water
Outlet
SinkSinkSower
Correct Installation
Incorrect installation