Aube Technologies TH115 A/F/AF User manual

TH115 -F-120GA
Owners Guide
Buttons and symbols
On/Stand By Switch
Use this switch to put the thermostat in sleep mode
when its use is no longer required (e.g. summer).
This will not affect the clock programming.
GFCI Warning Light and Test Button
Day & Clock Settings
Programming Mode
Mode Selection/Exit Programming
Floor/Ambient (Amb. only with B)
Current Mode Auto, Manual, Vacation
Current Program Number
Setpoint definition/Pre-defined Setpoints
Increase/Decrease Temperature
TH115 Description
Align the bracket tabs on the control module with the
holes located on top of the power base.
NOTE: Keep the thermostat’s air vents clean and free
NOTE: The screw cannot be removed completely.
Control Module Installation
Power base
Control module
from obstructions.
F
Thank you for choosing the AubeTH115 a programmable
thermostat that provides both energy savings and comfort
When power is applied for the first
time, the LCD dispays: 0:00, MO
(Monday), and temperature of the
floor .
Press HOUR - MIN to set the
current time.
Press DAY to set current day.
For AF and F models: one of the two
LO: The floor temperature is below
32ºF (0ºC), or the temperature
sensor is defective, or not con-
nected.
The heating indicator i is dis-
played and the relay is closed
(energized).
HI: The floor temperature is above
140°F (60°C), or the tempea-
ture sensor is defective.
Correct
Incorrect
First Power ON
F
following messages may be displayed
if the installation is incorrect:
24/7 Installation Support • Lifetime Technical Assistance • Free Design Service • www.WarmlyYours.com • [phone]
10103-A 04/08

The GFCI monitors the electrical flow for
any loss of current; if there is one, the
thermostat will cut off power to the heating
system. We recommend you test the GFCI
immediately after installing the control
module, and once a month thereafter to
ensure it is operating properly. To test:
Increase the temperature until the
heating indicator is displayed.
Press TEST:
•Successful: the TEST warning light is ON and
power to heating system is cut off.
•Unsucessful: the TEST warning light is OFF. Cut
power to heating system from the main power
panel and call customer service.
When successful, reset thermostat (Stand By/On) to
power the heating system.
NOTE: If the test warning light comes ON during normal
operation, cut power to heating system from the main
power panel and have an electrician verify the installation.
GFCI Test (GA & GB power baseonly)
The following temperature setpoints are pre-programmed:
To modify a setpoint:
Set the desired temperature using .
Press and Hold the or or
button until symbol is displayed.
Press RET to exit.
Symbol Description Default New
Comfort (when at home) 70°F 82°F
Economy (when asleep/
away from home)64°F 68°F
Vacation (during
prolonged absence) 50°F 50°F
Temperature Setpoint
A/AF F
Automatic —Executes the schedule.
Press MODE until is displayed. The cur-
rent program number is displayed.
You can temporary bypass the current pro-
gram by setting a specific temperature or
by pressing on a pre-defined setpoint button ( ) .
The new setpoint will be maintained until the begin-
ning of the next program.
Manual —Maintains a constant temperature.
Press MODE until is displayed.
Set temperature or press ( ) to use
pre-defined setpoint.
Vacation —Maintains the Vacation setpoint
during a prolonged absence.
Press until the icon is displayed.
Operating Modes
The TH115 programmable thermostat is pre-programmed
with the following schedule:
Programs MO TU WE TH FR SA SU
6:00 6:00 6:00 6:00 6:00 6:00 6:00
8:30 8:30 8:30 8:30 8:30 --:-- --:--
16:00 16:00 16:00 16:00 16:00 --:-- --:--
23:00 23:00 23:00 23:00 23:00 23:00 23:00
Time you
wake up and
desired
temperature
Time you
leave and
temperature
during your
absence
Time you
return home
and desired
temperature
Time you go
to bed and
overnight
temperature
FFFF
F
F
F
Pre-programed Schedule

Notes:
You can program up to 4 different programs per day.
Each day can have different programs.
It is sometimes faster to program the same schedule
for the entire week and then to modify the exception
days.
To modify:
Press PGM to access the programming mode
Press DAY to select the day to be programmed (hold
for 3 seconds to select all days of the week).
Press PGM to select the program number.
Press HOUR and MIN to set the time or press
CLEAR to clear the time (--:-- is disregarded).
Repeat steps 2 to 4 for remaining programs.
When completed, press RET to exit mode.
NOTE: After 60 seconds of inactivity, the thermostat will
automatically exit programming mode.
Modify the Schedule
Custom Grid
Use this blank grid to record your new schedule.
Model: A F AF
Temperature display: °F °C
Time display: 12hrs 24hrs
Prog Setpoint MO TU WE TH FR SA SU
Temperature Control
The TH115 thermostat works differently than conventional
electromechanical thermostats.
It is equipped with a proportional integral adaptive (P.I.A.)
controller which determines heating cycles by analyzing
the temperature behavior history within the room.
The P.I.A. controller reduces temperature variations
providing an accurate temperature control while
increasing user comfort.
The controller determines the amount of power required
by the heating system to maintain the setpoint
temperature.
Technical Support
Model: TH115 A / AF / F
Display range: 32°F to 140°F (0°C to 60°C)
Setting range (ambient): 40°F to 86°F (5°C to 30°C)
Setting range (floor limit): 40°F to 104°F (5°C to 40°C)
Pre-programmed temperature setpoints:
Comfort: A/AF: 70°F (21°C) and F: 82°F (28°C)
Economy: A/AF: 64°F (18°C) and F: 68°F (20°C)
Vacation: A/F/AF: 50°F (10°C)
Floor limit:AF: 82°F (28°C)
Accuracy:± 0.9°F (0.5°C)
Storage:-4°F to 120°F (-20°C to 50°C)
Temperature control: Proportional integral adaptive,
15-minute or 15-second heating cycles according to the
application and power base.
Memory backup: In the event of a power failure, an
internal circuit will maintain the programming. Only the
time will have to be set if the power failure is more than
two (2) hours. The thermostat will return to the same
operating mode as set before the power failure.
Warranty
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY
This product is guaranteed against workmanship defects for a
one year period following the initial date of purchase. During this
period, AUBE Technologies Inc. will repair or replace, at our
option and without charge, any defective product which has been
used under normal conditions.
The warranty does not cover delivery costs and does not apply to
products poorly installed or randomly damaged following
installation.
This warranty cancels and replaces any other manufacturer's
express or implied warranty as well as any other company
commitment. AUBE Technologies Inc. cannot be held liable for
related or random damages following the installation of this
product.
The defective product as well as the purchase invoice must be
returned to the place of purchase or mailed, prepaid and insured,
to the following address:
Aube Technologies Inc.
705 Montrichard
Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8
1 to 20% 21 to 40% 41 to 60% 61 to 80% 81 to 100%
(AF only)

Technical Support
Model: TH115 A / AF / F
Display range: 32°F to 140°F (0°C to 60°C)
Setting range (ambient): 40°F to 86°F (5°C to 30°C)
Setting range (floor limit): 40°F to 104°F (5°C to 40°C)
Pre-programmed temperature setpoints:
Comfort: A/AF: 70°F (21°C) and F: 82°F (28°C)
Economy: A/AF: 64°F (18°C) and F: 68°F (20°C)
Vacation: A/F/AF: 50°F (10°C)
Floor limit:AF: 82°F (28°C)
Accuracy:± 0.9°F (0.5°C)
Storage:-4°F to 120°F (-20°C to 50°C)
Temperature control: Proportional integral adaptive,
15-minute or 15-second heating cycles according to the
application and power base.
Memory backup: In the event of a power failure, an
internal circuit will maintain the programming. Only the
time will have to be set if the power failure is more than
two (2) hours. The thermostat will return to the same
operating mode as set before the power failure.
Warranty
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY
This product is guaranteed against workmanship defects for a
one year period following the initial date of purchase. During this
period, AUBE Technologies Inc. will repair or replace, at our
option and without charge, any defective product which has been
used under normal conditions.
The warranty does not cover delivery costs and does not apply to
products poorly installed or randomly damaged following
installation.
This warranty cancels and replaces any other manufacturer's
express or implied warranty as well as any other company
commitment. AUBE Technologies Inc. cannot be held liable for
related or random damages following the installation of this
product.
The defective product as well as the purchase invoice must be
returned to the place of purchase or mailed, prepaid and insured,
to the following address:
Aube Technologies Inc.
705 Montrichard
Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8
As an ENERGY STAR®partner, Aube Technologies has
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
04/08/2003 920-115-007-00-1-A
If you have any questions concerning the
installation or programming of the TH115
programmable thermostat, call our technical
support team at:
800.875.5285
For more information on our products, visit us at:
www.warmlyyours.com