Aube Technologies TH115 A/F/AF User manual

TH115 FLOOR HEATING THERMOSTAT INSTRUCTIONS
Once the floor heating system has been installed & commissioned, open the hinged side panels to reveal the
programming controls - turn the unit on using the on/off switch on the top left.
TO SET THE DAY AND TIME
The current day and time needs to be entered into the Thermostat. First set the current time by pressing the “Hour”
button once, to cycle through the 24hr clock. Once you have set the correct hour repeat the procedure for the minutes
by pressing the ‘min’ button.
Next the current day needs to be entered. Press the ‘day’ button to cycle through & select the correct day of the week.
OPERATION OF THE THERMOSTAT
The thermostat can be operated in either MANUAL mode (signified by a picture of a hand) or TIMER mode (signified by a
picture of a clock). You can switch between the two modes by pressing the ‘mode return’ button on the bottom left.
MANUAL MODE
When you are in manual mode the display shows hand with a pointed finger, in the centre of the screen. You can set
the desired temperature by pressing the up and down arrows on the right hand side. Arrow up or down to the desired
temperature – the thermostat will then display the actual temperature (not the set temperature) & it will draw power until
the desired temperature is reached.
TO PROGRAM THE THERMOSTAT TIMER
First press the program button on the left side – you will see a small symbol at the bottom of the screen with a house &
a number ‘1’ inside & the sun rising.
To set the heating operations for one particular day, Press the ‘day’ button to cycle through the days of the week. If you
want the same times for every day of the week, press and hold the day button for a few seconds. The display will
now change to show every day of the week (Mon-Sun). You can alter the operation of individual days later if you wish.
Example Times: [on 04:00] [off 08:00] [on 16:00] [off 21:00]
Step 1. Once you have selected the day(s) you want to program the heating for, select the time at which you want the
heating to be turned on. Do this by pressing the hour button to cycle through the 24hr clock and then pressing the
minute once to cycle through 15 minute increments. e.g. 04:00.
Step 2. To select the first off time, press the program button again & the display will now show at the bottom of the screen
a house with a number ‘2’ inside & a person leaving the house. This is asking what time you want the heating to be turned
off. Press the hour and minute buttons to select the desired “off” time. e.g. 08:00.
Step 3. To select the second on time, press the program button again. The display will now show at the bottom of the
screen a house with a number ‘3’ inside & a person returning home. This is asking what time you want the heating to be
turned on for a second time in the day. You can have just one on and one off in a day if you wish & if so just press the
clear button so no time is set for this program. If you wish to set a second on time, press the hour and minute buttons to
select the desired on time. e.g. 16:00.
Step 4. To select the final off time, press the program button again & the display will now show at the bottom of the screen
a house with a number ‘4’ inside. This is asking what time you want the heating to be turned off for a second time in the
day/days. e.g. 21:00, again press the hour & minute buttons to select the required time. If you only want one on/off per
day, just press the clear button so that no time is entered for this program.
This completes programming of the times.

Step 5
Press the mode return button. This will take you out of programming and back to the main screen. If the current time is
within an on cycle there may be a slight delay of up to 20 second before the heating will activate.
TO SET THE TEMPERATURE FOR PROGRAM TIMES
The current model of the TH115 thermostat can be switched between FLOOR sensor (Fdisplayed on screen) and AIR
sensor with floor limit (AF). Most people prefer to set the floor temperature, but if you wish to switch between the two,
please see item 2 (configuration) on manufacturers instruction. Switch 3 on the face plate will switch between floor
sensing & sir sensing.
Using the up and down arrow keys set the temperature you want for the on cycle. e.g. 26°C. Then press and hold the
Sun button for a few seconds. The display will show a sun symbol in the centre of the screen, indicating that the “on”
temperature has been set.
Repeat the procedure above to set the temperature for the off cycle. e.g.. 18°C by pressing and holding the half
moon button. The display will show a half moon symbol in the centre of the screen, indicating that the “off” temperature
has been set.
The suitcase symbol is for when you go on holiday or for use in the summer time when you are not using the system. This
can set as low as 5°C. To set the temperature for the vacation cycle. e.g. 5°C. by pressing and holding the Suitcase
button. The display will show a suitcase symbol in the centre of the screen, indicating that the “vacation” temperature has
been set.
When you have finished setting the temperatures & times, press the mode button & ensure the clock is displayed. If the
clock is flashing, simply press mode once more & it will stop flashing.
RECOMMENDATIONS
If you floor heating is installed in a bathroom, we would recommend setting the timer for early morning (say 0400 hrs) so
that the room is comfortable when you get up & then depending on your location/comfort levels, set the off time & second
on/off time to suit your lifestyle.
For under-tile or in screed heating we would recommend setting the timer to start approx 1-2 hours before you are usually
in the room
If you have floor heating installed in the slab it will usually take several hours to heat up & so this is particularly well
suited to using a smart meter to take advantage of ‘off peak’ prices. If you have a smart meter, we recommend that you
operate the heating overnight to coincide with the lowest energy cost – the heat will then be stored in the slab for several
hours & may not need to come on again until the following night. Current Synergy off-peak times are 2100hrs – 0700 hrs,
so this is what you should chose as program 1 & 2 times (or say midnight to 0700 hrs if you are not usually up late)
If you are using floor heating as your only heating, then during cold spells you may need to ‘boost’ the heating in the
afternoon so that the house remains warm during the evening. To do this we would recommend that you set the second
on/off times (program 3 & 4) from say 1500 hrs – 1700 hrs. This is the ‘shoulder’ rate & is currently around the same cost
as the standard tariff – this should give you a comfortable room for the rest of the evening until the main off-peak time
starts again.
With a smart meter, you should always try to avoid operating the heating during the peak winter times of 1700 – 2100 hrs
Monday-Friday. Weekends are of course at a reduced rate during the day & night.
If you require any assistance, please contact Radiant Floor Heating, Wangara on 08 9302 4140 or visit our
website: www.radiantfloorheating.com.au