Aube Technologies TH115 A/F/AF User manual

Owner’s Guide
Guide du propriétaire
Guía para el usuario
TH115 (24 V; 15 sec.)
Programmable thermostat
Thermostat programmable
Termostato programable
69-2618EFS-01 (5 x 3.125).book Page 1 Thursday, November 21, 2013 2:00 PM

Need Help?
We are here to help. Call 1-800-831-2823.
Besoin d’aide?
Nous sommes là. Composez le 1 800 831-2823.
¿Asistencia?
Estamos aquí para ayudarlo. Llame al 1 800 831-2823.
69-2618EFS-01 (5 x 3.125).book Page 2 Thursday, November 21, 2013 2:00 PM

ENGLISH
TH115 (24V model)
Overview
Before you start..................................................2
About your thermostat........................................3
Controls..............................................................4
Display ...............................................................5
Installation
Installing the thermostat.....................................6
Connecting the floor sensor ...............................7
Wiring diagrams ............................................. 8-9
Setting the configuration switches....................10
Setup
Time and day....................................................11
Daylight Saving Time .......................................12
Floor temperature limits....................................13
Preset temperatures.........................................14
Default schedule ..............................................15
Modifying the schedule ....................................16
Operation
Running the schedule (Automatic mode).........17
Temporary override of schedule.......................18
Permanent override (Manual mode) ...............19
Before going on vacation (Vacation mode) ......20
Appendices
Error messages................................................21
Technical specifications....................................22
Warranty...........................................................23
Table of contents
69-2618EFS-01 (5 x 3.125).book Page 1 Thursday, November 21, 2013 2:00 PM

Owner’s Guide
2
ENGLISH
Read the entire document
CAUTION:
• This thermostat MUST be used ONLY with solid-state relays. The use of
electromechanical relays will result in reduced life expectancy and in the possibility of
overheating of these devices.
• For a new installation, choose a location about 1.5 m (5 ft.) above the floor.
• The thermostat must be installed on an inside wall facing the heating system (except for floor
heating systems).
• Avoid locations where there are air drafts (top of staircase, air outlet), dead air spots (behind
a door), direct sunlight or concealed chimney or stove pipes (except for floor heating
systems).
• Do NOT install the thermostat in an area where it can be exposed to water or rain.
• Keep the thermostat's top and bottom air vents (openings) clean and unobstructed at all
times.
Before you start
69-2618EFS-01 (5 x 3.125).book Page 2 Thursday, November 21, 2013 2:00 PM

TH115 (24V model)
3
ENGLISH
The TH115 programmable thermostat has three temperature control modes:
See page 12 on how to change the temperature control mode setting.
* Select models only; required for floor heating applications only.
About your thermostat
A mode: controls the ambient air temperature
F mode: controls the floor temperature using an external temperature sensor
AF mode: controls the ambient air temperature
maintains the floor temperature within desired limits using an external temperature
sensor
Supplied Parts
• One (1) thermostat
• Two (2) mounting screws
• Two (2) plastic anchors
• One (1) floor sensor *
• One (1) flat-tip screwdriver *
69-2618EFS-01 (5 x 3.125).book Page 3 Thursday, November 21, 2013 2:00 PM

Owner’s Guide
4
ENGLISH
Controls
On/Off switch*
Day button
Temperature adjustment buttons**
Program button
Mode selection / program exit
Presettemperaturebuttons
(see page 14)
Backlight button**
Program clear button
Hour button
Minutes button
*
Place at Off to cut power to the heater (e.g., in the summer). This will not affect the time and temperature settings.
** When the backlight button or either of the buttons is pressed, the display illuminates for 12 seconds.
69-2618EFS-01 (5 x 3.125).book Page 4 Thursday, November 21, 2013 2:00 PM

TH115 (24V model)
5
ENGLISH
Display
Temperature*
Operation mode icon
(see pages 17,19 & 20)
Period (see page 15)
Time
Number of flames varies
according to heating intensity
Preset temperature icon (see page 14)
Appears when the setpoint
temperature is displayed*
Temperaturecontrolmode
(see pages 3 & 10)
Day
* The thermostat normally displays the actual (measured) temperature. To view the setpoint temperature, briefly press
either of the buttons. The setpoint will appear for 5 seconds. To change the setpoint temperature, press one of the
buttons until the desired temperature is displayed. To scroll faster, press and hold the button.
69-2618EFS-01 (5 x 3.125).book Page 5 Thursday, November 21, 2013 2:00 PM

Owner’s Guide
6
ENGLISH
Turn the heating system off at the main electrical panel.
Loosen the bottom screw and remove the thermostat faceplate from its
wallplate. (The screw cannot be completely removed.)
Wire the thermostat. See typical wiring on pages 8 and 9.
If the thermostat will be used in F or AF mode (see page 10), connect the
floor sensor (see page 7).
WARNING: For floor heating applications, you must install a separate
ground protection device at the main electrical panel or use a thermostat
with built-in ground protection device.
Install the wallplate on the wall using the provided screws and wall
anchors.
Set the configuration switches (see page 10).
Install the faceplate back on the wallplate and tighten the screw. If there is
a sticker on the screen, peel it off.
Apply power to the heating system at the main electrical panel.
Installing the thermostat
Wallplate
Faceplate
69-2618EFS-01 (5 x 3.125).book Page 6 Thursday, November 21, 2013 2:00 PM

TH115 (24V model)
7
ENGLISH
Connect the floor sensor between terminals R and S (no polarity).
• The sensor wires must not come in contact with the
electrical wires and must be routed outside the
electrical box and follow the wall down to the floor.
• Position the sensor cable such that it does not come in
contact with the floor heating wires. The sensor must
be centered between two floor heating wires for best
temperature control.
• Do NOT staple the sensor head (the plastic end) to the
floor. Doing so might damage the sensor. Any damage
might not be noticeable during testing but can become
apparent several days later.
Connecting the floor sensor
Load
69-2618EFS-01 (5 x 3.125).book Page 7 Thursday, November 21, 2013 2:00 PM

Owner’s Guide
8
ENGLISH
Wiring diagram - Single SSR with Built-in Transformer
Electrical
Panel
Heater
Blue Red
Black
TH115
SSR
69-2618EFS-01 (5 x 3.125).book Page 8 Thursday, November 21, 2013 2:00 PM