AUDIOLINE CLD60 User manual

CLD60
Telephone with Caller Display
User guide

1
TABLE OF CONTENTS AUDIOLINE CLD60
AUDIOLINE CLD 60
User guide
TABLE OF CONTENTS
Installation .................. 2Caller Display ................. 11
Function ................... 2Explanation ................. 11
Assembley instructions ....... 3Call Indications .............. 11
Parts List/Battery ............ 3 To View the new call information. 12
Assembly .................. 3Erase phone number ...........13
Table/Wall Mounting ........ 4Memory Full ................13
Wall Installation/Display ...... 5Autodial ....................14
Set Date and Time ........... 6
Set Language ............... 6Telephone book ................ 14
Explanation of Phone Book .....14
The telephone ................ 7Text input ...................15
To Call/Call Timer ........... 7Store Phone Number/Name .....16
Last Number Redial .......... 7Erase Number/Name ..........17
Volume control ............. 8Dialling a Phone Book number ..17
Mute button .................8
Pause function ...............8 Special functions .............. 18
Ringing signal .............. 8Least Cost Routing(LCR) ......18
Network Feature buttons .......9 E-mail indicator .............. 20
Call Waiting/Call Forward .....9 Message waiting ............. 20
Call Forward continued ........10
Trouble shooting .............. 21
If the phone doesn't work ....... 21
Other Information ............ 22
Guarantee ................... 23

ERASE
DIAL
CW
2
AUDIOLINE CLD60 INSTALLATION
FUNCTIONS
1Erase button 10 Switch for ringing signal
2Dial button 11 Dial button, 0-9, *, #
3Memory button 12 Network feature buttons
4Store button 13 Scrolling button UP
5Mute button 14 Scrolling button DOWN
6Recall button 15 Indicator
7Outlet for handset cord (on the side) 16 Display
8Redial/Pause button 17 Outlet for line cord (at rear)
9Outlet for handset cord (on handset) 18 Switch for handset volume

3
INSTALLATION AUDIOLINE CLD60
ASSEMBLY INSTRUCTIONS
PARTS LIST
1 - CLD60 Telephone
1 - Telephone Handset
1 - Line cord
1 - 3 x 1.5volt AA Batteries (supplied)
BATTERY
The Caller Display and memory functions need 3 x 1.5 volt AA batteries to function.
PRemove the line cord before you change the battery.
PTo install the batteries unscrew and remove the battery cover from the battery holder
(on the base of the telephone) and insert the new batteries ensuring correct polarity.
PIndication of flat batteries will be seen in the telephone display (see diagram page
5). Remove the old batteries, wait a couple of minutes to enable the Caller Display
to reset correctly, and then insert the new batteries. Observing correct polarity.
PReconnect the line cord.
ASSEMBLY
PPlug the Line cord into the telephone (17 on the diagram on page 2) by inserting the
plug until you hear a click.
PPlug the Handset into the telephone (7 on the diagram on page 2) again listen for the
click.
PTo remove either of the plugs depress the plastic tab on the plug and withdraw.
Do not position the telephone in direct sunlight. The rubber feet on the base of the
telephone can leave marks on sensitive surfaces.

4
AUDIOLINE CLD60 INSTALLATION
SLIDE SUPPORT
On the base of the CLD60 is a “slide support”. This is used to position the phone
correctly for use when desk/wall mounting. Please refer to the diagram below for correct
positioning.
DESKTOP USE
When this “slide support” is slid onto the base of the phone from the top downwards the
CLD60 is ready for desk top use. See diagram below.
WALL MOUNTING
When this “slide support” is slid ontothe base of the phone from the bottom upwards, the
CLD60 is ready for wall mounting. See diagram below and Page 4.
Desktop position Wall mount position

5
INSTALLATION AUDIOLINE CLD60
WALL INSTALLATION
To install the telephone on the wall:
PThe CLD60 will fit directly onto the standard Telstra wall plate, or
PUse the slide support as a template to mark the position of the 2 screw holes for
attaching directly to the wall. The distance between the two holes will be 82mm.
PScrew in the mounting screws until there is a 3mm gap between the wall and the screw
head.
PFasten the slide support to the telephone in the “wall mount” position and hook the
telephone onto the screws and press down into place.
PConnect the line cord to the wall socket - The phone is now ready to program.
THE DISPLAY
With the Handset in place the telephone is on “Standby”.
The display (16 in the diagram on page 2) has 15 alpha-numeric characters on the top line
for the display of text messages, 13 segments on the second line to indicate the Caller
Display phone number, and on the 3rd line, will show the new calls received, flashing
envelope, Caller Display memory store number, the time, the date, and the battery low
indicator. See diagram below.
Presentation of text message
Caller Display
New Caller Display Low battery
Calls Memory Time Date

6
AUDIOLINE CLD60 PROGRAMMING
SET DATE AND TIME
To set the correct date and time on the display do the following:
PPress the [STORE] button (4 on the diagram on page 2) for 2 seconds and release.
The display will show "LANGUAGE".
PPress the UP Arrow until the display shows "SET TIME".
PPress [ERASE] button. The hours will flash on the display. Press the UP or
DOWN arrows to step to the correct hour. Press [ERASE] button to store the
hours.
PThe minutes on the display now flash. Use the UP and DOWN arrows
to set the minutes. Press [ERASE] button to store the minutes.
PThe days on the display now flash. Use the UP and DOWN arrows to
set the day. Press [ERASE] to store the day.
PThe month on the display will now flash. Press the UP and DOWN
arrows to set the month. Press the [DIAL] button (2 on the diagram on Page 2) to store
the month and return to standby.
SET LANGUAGE
The telephone display will show text in a choice of languages. The language choice is:
Swedish, English, Finish, Danish, Norwegian, Turkish, German, Dutch, Portuguese,
Italian, Spanish and French. To set your chosen language do the following:
Press the [STORE] button down for 2 seconds, release the button.
The display will show "LANGUAGE".
Press [ERASE] button.
PPress the UP or DOWN arrows to choose your language.
PPress the [DIAL] button to store the setting and return to standby.

7
THE TELEPHONE AUDIOLINE CLD60
MAKE A CALL
#Lift handset and wait for Dial Tone.
#Dial the number.
#Finish the call by replacing the handset.
CALL TIMER
Outgoing Calls
The telephone has a call timer function that will show the length of a call on the display.
The example in the diagram below shows a call of 8 minutes 46 seconds duration.
Incoming Calls
On an incoming call the timer will show after about 30 seconds into the call and indicate
the total call time when the call is completed.
LAST NUMBER REDIAL
If the number you called is busy or if you want to call the previous number again, simply;
PLift the handset and wait for Dial Tone.
PPress the [REDIAL/II]button (8 on the diagram on page 2) . The phone will call the last
number you dialled.

8
AUDIOLINE CLD60 THE TELEPHONE
VOLUME CONTROL
The sound level in the handset is adjusted with the switch on the side of the handset. The
sound level changes between HIgh and LOw (18 on the diagram on page 2).
MUTE BUTTON
The [MUTE]button (5 on the diagram on Page 2) will cut off the handset microphone
when pressed. This will allow you to speak privately to a third party while waiting on
your call. Push the [MUTE]button again to switch the handset microphone back on.
The word “MUTE” shows in the display when the [MUTE]button is pressed.
PAUSE FUNCTION
When you make a call with a number stored in the telephones [MEMORY](3 on the
diagram on page 2) and you need a pause during the dialling , eg., on an international or
acall through a switchboard, you can insert a pause with the [REDIAL/II]button (8 on
diagram on page 2).
The display will show a “P” indicating a dialling pause.
RING SIGNAL
On the right hand side of the telephone (10 on the diagram on page 2) there is a switch
that allows you to change the volume of the ringing signal. The switch has three positions;
Off, Low, and High. The symbol indicates the ring signal is turned off.

9
THE TELEPHONE AUDIOLINE CLD60
NETWORK FEATURE BUTTONS
The buttons CW, CALL FWD 1 and 2 above the dialling buttons (12 on the diagram on
page 2), are used for easy access to the frequently used Telstra network services.
CALL WAITING (CW)
To switch between callers when you hear the call waiting tones simply press the [CW]
button. The first caller is put on hold and you can talk to the second caller. Each
subsequent press of the [CW] button allows you to toggle between the callers.
When your conversation is finished hang up by placing the handset on the cradle.
CALL FORWARD (CALL FWD)
Call Forward or Call Diversion is a network feature that allows your calls to be
forwarded to another number under certain conditions. For example, if your telephone is
not answered or you are going to be out, you can program the CLD 60 to forward your
calls to the number of your choice.
CALL FWD 1
Immediate
When leaving home you can program the CLD 60 to forward all your calls immediately
to another number, for example your mobile phone:
#Lift the handset
#Press the [CALL FWD 1] button
#Dial the forward number, eg, your mobile or office number
#Press the [#] button to store
#Listen for the facility tone and replace the handset.