Audiopipe APSM-1150 User manual

English
2 1 3 4
APSM-1150
2
1 345
1. RCA Input Jacks
2. Remote Bass Level Control 3. Power Indicator LED 4. Protection Circuit Indicator LED
1. Speaker Connection
2. Ground
3. Remote Turn-on Input
4. Battery +12V Input
5. 40Amp Fuse

1. SUBSONIC
2. Low Pass Filter
3. GAIN Control
21 3

1. Speaker Connection
2. Battery +12V Input 3. Remote Turn-on Input 4. Ground
1. Remote Bass Level Control
2. RCA Input Jacks
3. Bridge in
2
1 5 6
21 3 4
APSM-1300
4. Bridge out
5. Power Indicator LED
6. Protection Circuit Indicator LED
3 4

English
1. Bass boost Level
2. Bass boost Frequency
3. SUBSONIC
4. Low Pass Filter
5. GAIN Control
521 3 4

21
5 621 3 4
APSM-2075
3
1. Left Speaker Output
2. Right Speaker Output
3. RCA Input Jacks
1. Ground
2. Remote Turn-on Input
3. Battery +12V Input
4. 30Amp Fuse
5. Protection Circuit Indicator LED
6. Power Indicator LED

English
1. GAIN Control
2. Filter Select Switch
3. HPF Control
21 3
4. Bass boost Level
5. LPF Control
54

2 1
5 621 3 4
APSM-4050
3
1. RCA Input Jacks
2. Rear Speaker Output
3. Front Speaker Output
1. Ground
2. Remote Turn-on Input
3. Battery +12V Input
3. 40Amp Fuse
5. Protection LED
6. Power LED

English
76 8
21 5
910
3 4
1. Front GAIN Control
2. Front Filter Select Switch
3. Front HPF Control
4. Front Bass boost Level
5. Front LPF Control
6.
7.
8.
9.
10.
Rear GAIN Control
Rear Filter Select Switch
Rear HPF Control
Rear Bass boost Level
Rear LPF Control

IMPORTANT:
When bridging two amplifiers please refer the bridging wiring chart.
•When bridging two amplifiers you should use same model amplifiers.
•Please make sure the negative speaker terminal of two amplifiers are connected by the
same gauge cables as the positive terminal being used.
•
DO NOT connect any signal cables with the input RCA jacks when bridged as slave unit.
•
•The LPF, Input level and remote functions will be disabled on slave amplifier when
bridged.
All the functions of the slave amplifier will be adjusted by the master amplifier.
•
We recommend you have the installation done by an Authorized Audiopipe Dealer. The
ground wire should be connected directly with the chassis of your vehicle which should
be a metal to metal ground point connection. The amplifier must be mounted securely at
a solid, dry and low vibration surface in the trunk or passenger area. Mount the amplifier
in an open air area to insure proper heat dissipation. Mount the amplifier in a place where
you can access it easily to set the input controllers. Install all amplifier cables as far as
possible from car electrical cables such as the car ignition cable.

One Speaker Mono
APSM-1150
5V MAX.
SIGNAL INPUT
REMOTE CONTROL
Chassis Ground
(Bare Metal)
Remote
BATTERY
1 MINIMUM
Ω

One Speaker Mono
APSM-1300
5V MAX.
SIGNAL INPUT
REMOTE CONTROL
Chassis Ground
(Bare Metal)
Remote
BATTERY
1 MINIMUM
Ω
FUSE

Two Speaker Mono
APSM-1300
5V MAX.
SIGNAL INPUT
REMOTE CONTROL
Chassis Ground
(Bare Metal)
Remote
BATTERY
2 MINIMUM
Ω
2 MINIMUM
Ω
FUSE

Two Amplifiers to One Channel
APSM-1300
Chassis Ground
(Bare Metal)
Remote
BATTERY
2 MINIMUM
Ω
FUSE
Chassis Ground
(Bare Metal)
BATTERY
FUSE
Remote
5V MAX.
SIGNAL INPUT
REMOTE CONTROL

APSM-2075
Chassis Ground
(Bare Metal)
Remote
2-Channel Full-Range Operation
BATTERY
Right Speaker +
Right Speaker –
Left Speaker +
Left Speaker –

Bridged - Mono Subwoofer System
APSM-2075
HPFFLAT
HPFGAIN
MIN MAX
90 500
50Hz 1.2KHz

APSM-2075
2-Channel Full-Range Satellite, or Subwoofer FLAT System
HPFFLAT
HPFGAIN
MIN MAX
90 500
50Hz 1.2KHz
HPFFLAT
HPFGAIN
MIN MAX
90 500
50Hz 1.2KHz
HPFFLAT
HPFGAIN
MIN MAX
90 500
50Hz 1.2KHz

APSM-4050
4-Channel Full-Range Operation
Chassis Ground
(Bare Metal)
Remote
BATTERY
CH3 Speaker –
CH3 Speaker +
CH1 Speaker +
CH1 Speaker –
CH2 Speaker +
CH2 Speaker –
CH4 Speaker –
CH4 Speaker +

Bridged - Mono Subwoofer System
APSM-4050
CH2 Full Range
CH1 Full Range
HPF
GAIN
MIN MAX
MIN MAX
HPFFLAT
HPFFLAT
90 500
50Hz 1.2KHz
90 500
50Hz 1.2KHz

APSM-4050
HPF
GAIN
MIN MAX
MIN MAX
HPFFLAT
HPFFLAT
90 500
50Hz 1.2KHz
90 500
50Hz 1.2KHz
2-Channel Full-Range Satellite, or Subwoofer FLAT System
CH2
CH1
CH4
CH3