The Niagara 7000 owner’s manual contains considerable information to ensure optimal performance and troubleshoot both
common and rare system interactions. It is also a great primer to the technology that makes this unit so unique. However, we
appreciate and respect your valuable time. At the very least, we humbly ask that you follow this quick-start guide.
¡¡If the Niagara 7000 has been exposed to excessive rain, ooding, re, or has sustained considerable physical damage,
we ask that the unit be returned. Do not attempt to energize the unit or connect equipment to it!
¡¡The power source to which the Niagara 7000 is connected should be 120-127VAC single phase nominal voltage, 20
amps (current capacity RMS). However, the Niagara 7000 will operate very well with a 15-amp service outlet. For proper
operation, the Niagara 7000 requires a safety ground (supplied via the power utility AC wall outlet).
¡¡The Niagara 7000 may be placed on any table, cabinet, shelf, or oor. When rack-mounting is required, the four
threaded feet may be removed with a standard Phillips screwdriver.
¡¡Placement or proximity to other components is not critical, and, under standard use, the Niagara 7000 does not
produce appreciable heat.
¡¡Once the Niagara 7000 is placed, an appropriate 20-amp-rated AC cord must be connected to the rear panel AC inlet
(IEC-C20) connector. The AC cord must have an IEC-C19 female-end connector and a grounded male 120VAC Edison/
NEMA plug for use in North America or Taiwan.
¡¡Connecting AC cables to the Niagara 7000’s NRG Edison AC outlets – WARNING! The AudioQuest NRG-Edison AC
outlets feature the strongest grip of any commercially available AC outlet in history. They will require slow and careful
“wiggling.”When either inserting a plug into these receptacles or removing an AC cord’s male plug from the receptacles,
gently move the male AC cord’s plug from side to side while providing an even forward or backwards pressure.
¡¡High Current/Low-Z Power Banks: There are two High Current/Low-Z Power banks (labeled “1” and “2”) with two
AC outlets each. The outlets feature our Transient Power Correction Technology, and are designed to enhance the
performance of power ampliers via our circuit’s low-impedance transient current reservoir. Power ampliers,
monoblock ampliers, integrated ampliers, powered receivers, or powered subwoofers should only be connected
to these four outlets.
¡¡Power Correction Switch: This rear-panel–mounted switch MUST be set in the ENGAGE position, regardless of the
equipment (line-level, digital, video components or power ampliers) that is connected to the Niagara 7000. It may
not function properly otherwise. If necessary, see user manual set-up for more detailed information. (Otherwise,
please place this switch in the ENGAGE position.)
¡¡Ultra-Linear Noise-Dissipation System/Dielectric-Biased Symmetrical Power Banks: These are for all line-level,
digital, and video products (typically). There are four banks that utilize this technology within the Niagara 7000.
Further, the rst two banks (3 and 4) are 100% isolated from banks 5 and 6.
¡¡I hear a slight buzzing sound coming from the Niagara 7000. Is it damaged? No, it’s not damaged (or, at least,
damage is very unlikely). If you’re in an extraordinarily quiet room and you hear this buzzing sound only when in
relatively close proximity to the Niagara 7000, or only when you place your ear next to the unit, the buzzing is normal
and cannot be entirely eliminated. Although, in some cases, it can be considerably reduced via careful routing of one
or more component power supplies that have severely clipped AC waveforms, and moving them to the adjacent
Symmetrical Power Bank, or at times the High Current Bank. See the Niagara 7000 manual for detail information
about magnetostriction.
Quick-Start Guide
Niagara 7000
Low-Z Power
|
Noise-Dissipation System
