Audiovox Prestige P-945 User manual

P-945
OO
OO
OWNER'SWNER'S
WNER'SWNER'S
WNER'S
MAMA
MAMA
MANUALNUAL
NUALNUAL
NUAL
AM/FM/MPX RADIO WITH DETACHABLE FRONT PANEL,
COMPACT DISC PLAYER, CD CHANGER CONTROLS
AND QUARTZ CLOCK

INDEX
Page
Operating Instructions ................................................................ 3 - 9
Specifications ...............................................................................10
CD Changer Controls...................................................................11
Setting the Clock ..........................................................................12
CD Player Error Codes.................................................................13
CD Changer Error Codes.............................................................13
Care and Maintenance.................................................................14
Warranty.......................................................................... Inside Back Cover

OPERATING INSTRUCTIONS
-3-
1ON/OFF POWER BUTTON
Press this button to turn the unit on or off. If the unit is off and
the ignition switch is "on", the unit will turn on automatically
when a disc is inserted, or when the "MODE" switch or "BAND"
switch is pressed.
2VOLUME / LEVEL CONTROL
To increase the volume level, press the button. The volume
will increase and the level will be shown on the display panel
from a minimum of “VOL 00” to a maximum of “VOL 39”. To
increase the volume quickly, keep the button pressed. To
decrease the volume level, press the button. Keep the button
pressed to decrease the volume quickly. The display will
automatically return to the normal indication 5 seconds after
the last volume adjustment or when another function is activated.
These buttons are also used in conjunction with the ''AUDIO
SELECT" (SEL) button 3to adjust the bass, treble, balance,
and fader levels as described in 4, 5, 6and 7.
3AUDIO SELECT (SEL) BUTTON
This button is used to select the audio function (volume, treble,
bass, balance, or fade) to be adjusted using the Volume/Level
Control 2. Pressing the "SEL" button will select bass (“BAS”
on the display), treble ("TRE"), balance (“BAL”), fader
(“FAD”) or volume (“VOL”). The display will automatically
return to the normal indication 5 seconds after the last adjustment
or when another function is activated. The unit will produce a
single beep tone whenever the button is pressed.
4BASS CONTROL
To adjust the bass level, first select the Bass mode by pressing
the "SEL" button 3so that the “BAS” indication appears on the
display panel. Within 5 seconds of choosing the Bass mode,
press the or button of the Level Control 2to adjust the
bass response as desired. The bass level will be shown on the
display panel from a minimum of -12 to a maximum of +12 (0
is flat response). The display will automatically return to the

-4-
normal indication 5 seconds after the last adjustment or when
another function is activated.
5TREBLE CONTROL
To adjust the treble level, first select the Treble mode by press-
ing the "SEL" button 3so that the “TRE” indication appears on
thedisplay panel. Within 5secondsofchoosing theTreblemode,
press the or button of the Level Control 2to adjust the
treble response as desired. The treble level will be shown on
thedisplay panelfrom aminimum of-12 toa maximumof +12 (0
is flat response). The display will automatically return to
the normal indication 5 seconds after the last adjustment or
when another function is activated.
6LEFT/RIGHT BALANCE CONTROL
To adjust the left-right speaker balance, first select the Balance
mode by pressing the "SEL" button 3so that the “BAL” indica-
tion appears on the display panel. Within 5 seconds of choos-
ing the Balance mode, press the or button of the Level
Control 2to adjust the balance as desired. The set into that
pre-set memory position. The balance position will be shown on
the display panel from “BAL.L 16” (full left) through “BAL.R 16”
(full right). When the volume level between the left and right
speakers is equal, “BAL 00” will be shown on the display panel.
The display will automatically return to the normal indication 5
seconds after the last adjustment or when another function is ac-
tivated.
7FRONT/REAR FADER CONTROL
To adjust the front-rear speaker balance, first select the Fader
mode by pressing the "SEL" button 3so that the “FAD” indica-
tion appears on the display panel. Within 5 seconds of choos-
ing the Fader mode, press the or button of the Level
Control 2to adjust the front-rear speaker balance as desired.
Thefader position willbeshownon thedisplaypanelfrom “FAD.R
16” (full rear) through “FAD.F 16” (full front). When the level
between the front and rear speakers is equal, “FAD 00” will be
shown on the display panel. The display will automatically
return to the normal indication 5 seconds after the last
adjustment or when another function is activated.
8LOUDNESS CONTOUR (LOUD)
When listening to music at low volume levels, this feature will
boost the bass and treble ranges to compensate for the char-
acteristics of human hearing. Press the "LOUD" button to acti-
vate this feature and the indication "LOUD" will appear on the
display panel. Pressing the button again will deactivate
the feature (the "LOUD" indication will disappear from the dis-
play panel).
9AUDIO MUTE (MUTE)
This button is used to mute the volume from the system. By
pressing the button,a flashing "MUTE" indication will appear
on the display panel and the volume will be muted. Pressing the
Mute button again, or activating the Volume Control 2Select
("SEL") button 3"LOUD" button, or Equalizer ("EQ") button will
return the volume level to the setting in use before the Mute
function was activated.
bl AM/FM BAND SELECTOR (BAND)
During radio operation, each momentary press of this button will
changetheradioband. Theindication“AM1”,“AM2”,“FM1”,“FM2”,

-5-
or “FM3” will appear on the display panel according to your
selection.
During disc play, pressing this button will stop play of the disc
and switch to radio operation without ejecting the disc. During
this time, the IN indication will remain on the display panel
to show that a disc is still loaded in the unit. Press the "Mode"
button cr to return to disc play from the beginning of the last
track in play.
bm MANUAL UP/DOWN TUNING (+ / -)
AUTOMATIC SEEK TUNING
Each time the + button is tapped, the radio will tune one
frequency step higher. Similarly, each tap of the - button will
tune one frequency step lower. To manually tune in a station,
tap the button of the appropriate direction until the desired
frequency is reached.
Pressing either button for longer than 2.0 seconds and then
releasingwill activatethe AutomaticSeek Tuningfunction. The
radio will seek the next available station and stop at that fre-
quency. The Seek function can be stopped by pressing the but-
ton again or activating any other tuning function.
bn AUTO-STORE TUNING (AS)
PRE-SET SCAN TUNING (PS)
During radio operation, press this button momentarily to scan
the 6 stations pre-set into the memories of that band. The unit
will stop at each pre-set station for 5 seconds before continuing
to the next pre-set station. During this time, the pre-set station
number ("CH") in the band will flash. Press the button again
momentarily to stop Pre-Set Scan operation and remain on
the selected frequency. The station number ("CH") stops
flashing.
Pressing the button for longer than 2 seconds will activate the
Auto-Store Tuning feature which will automatically scan the
band and enter up to 6 strong stations into the 6 pre-set
memories. After entering the stations into the memories, the
unit will automatically stop at each station for 5 seconds so each
can be heard. If you have already set the pre-set memories to
yourfavorite stations,activatingthe Auto-Storefeaturewill erase
those stations and enter the new strong stations. This feature is
most useful when travelling in a new area where you are not
familiar with the local stations.
bo STATION PRE-SET MEMORIES
To set any of the 6 pre-set memories in each band, use the
following procedure:
1. Turn the radio on and select the desired band.
2. Select the first station to be pre-set using the Manual Up/Down
or Automatic Seek Tuning Controls bm.
3. Press the pre-set button ("1-6") to be set and continue to
hold it in. After approximately 2 seconds, the pre-set number
will appear on the display panel, indicating that the station is
now set into that pre-set memory position. The station can
now be recalled at any time by pressing that button.
4. Repeat the above procedure for the remain in pre-sets on
that band and for the other 4 bands on the unit.

-6-
bp LIQUID CRYSTAL DISPLAY PANEL FUNCTIONS
The Liquid Crystal Display (LCD) panel displays the frequency,
time, and all activated functions, including five bar graphs
which provide a visual representation of the volume level
and the left and right channel balance levels. The volume level
is represented by three thin bar graphs. As the volume is
increased, the number of illuminated segments will increase.
The left and right channels are represented by the wider bar
graphs. As the strength of the signal applied to either the left or
right channel increases, the number of illuminated segments
will increase.
NOTE: It is a characteristic of LCD panels that, if subjected to
cold temperatures for an extended period of time, they
maytakelongertoilluminate thanundernormalconditions.
In addition, the visibility of the numbers on the LCD may
slightly decrease. The LCD read-out will return to normal
when the temperature increases to a normal range.
bq DISC SLOT
With the label surface facing up, gently insert the disc into the
slot until the soft-loading mechanism engages and disc play
begins. The indication illuminates and becomes animated,
the IN symbol lights, and the track number and elapsed
time will appear on the display panel.
CAUTION:This unit is designed for play of standard 5"
(12cm) Compact Discs ONLY. Do not attempt to use
3" (8cm) CD-Singles in this unit, either with or without
an adaptor, as damage to the player and/or disc can
occur. Such damage will not be covered by the
Warranty on this product.
br TRACK SELECT
These buttons are used to quickly select the beginning of a
particular track. With each momentary tap of the Forward Track
Select button (+ ), the next higher track number will be selected
if the button is pressed within one second. Similarly, with each
momentary tap of the Backward Track Select button ( - ), the
next lower track number will be selected ifthe button is pressed
within one second.
bs CUE/REVIEW FUNCTIONS
High-speed audible search to any section of the disc can be
made by the Cue and Review functions. Press and hold the
Cue button (+) to advance rapidly in the forward direction or
the Review button ( -) to advance rapidly in the backward
direction. During either function, the elapsed time within each
track will automatically be shown on the display panel.
bt CD TRACK ONE POSITION (TOP) SELECTOR
During disc play, press this button to return to beginning of first
track on disc. Disc counter will return to zero and "TRACK"
number 01 will appear on display panel.
bu REPEAT PLAY SELECTOR (RPT)
During disc play, press this button to repeat the play of the
selected track (“RPT” will appear on the display panel). Play
of the track will continue to repeat until the button is pressed
again and the “RPT” indication disappears from the display
panel. Repeat Play mode will also be cancelled by activating the
Random Play cl or Track Scan cm functions.

-7-
cl RANDOM PLAY SELECTOR (RND)
During disc play, press this button to play the tracks on the disc
in a random or shuffled order (“RND”) will appear on the display
panel). InRandom Playmode,pressing theForward TrackSelect
(+) or theBackward Track Select ( -) will also selecttracks in
a random order instead of the normal progression. Additional
presses will select tracks in random order. The Random Play
mode can be cancelled by pressing the button again (“RND”)
indication will disappear from the display panel) or by activating
the Repeat Play bu or Track Scan cm functions.
cm TRACK SCAN (SCN)
During disc play, press this button to play the first 10 seconds of
each track on the disc (“SCAN” will appear on the display panel).
When a desired track is reached, press the Scan button again
to cancel the function and play of the selected track will
continue. Track Scan mode will also be cancelled by activating
the Repeat Play bu or Random Play cl functions.
cn DISC EJECT ( )
Disc play is stopped, the disc is ejected and the unit will change to
radio operation by pressing this button. If the disc is not removed
from the unit and the button is pressed again, the disc will
be re-loaded.
If the disc is not removed from the disc slot within 15 seconds of
being ejected, it will automatically be re-loaded into the unit to
prevent it from being accidentally damaged. Play of the disc
can be resumed by using the CD Mode Selector cr to choose
CD player function.
co TIME/FREQUENCY SELECTOR (T/F)
This unit can display the clock time, radio frequency or CD player
functionson thedisplay panel. Pressing the Time/Frequency
Selector button when the radio frequency orCDplayer track
indication is shown will change the display to show the time.
The time display will automatically return to the radio frequency
or CD player function indication after 5 seconds.
cp FM MONO/STEREO SELECTOR (MO/ST)
During FM radio operation, this button is used to select mono or
stereo reception of the broadcast signal. Under normal re-
ception conditions, the unit should be left in the stereo mode, as
indicated by "ST "on thedisplay panel whenlistening toanFM
stereo signal. If the stereo signal is too weak for comfortable lis-
tening, press the button to switch to mono reception (the "ST "
indication will disappear from the display panel). To return to
the stereo reception mode, press the button again so that
the "ST " indication returns.
cq EQUALIZER SELECTOR (EQ)
The "EQ" button applies preset sound effects to the unit's
audio output signal. The "EQ" button, when pressed, will activate
oneof threeoperating modes ("ROCK, CLAS, or POP"). When
the "EQ" function is active, thebass and treble levelscannot be
changed. When the "EQ" function is not active, the unit re-
turns to the user-set bass and treble levels.

cr MODE SELECTOR (MODE)
This button is used to select the radio, or the playback mode for
the CD player or remote CD changer (if installed). Each press
of the button will select a different mode as indicated on the
display panel.
During CD player operation, this button may be used to change
to radio or remote CD changer mode ("CDC") without ejecting
the disc (the IN indication will remain on the display panel
to show that a disc is still loaded in the unit). Press the button
again to return to integral CD player mode and resume play of the
disc from the point at which it was stopped.
cs & ct DISC SELECT (CD+ & CD-)
These buttons are used to increase or decrease selection of
a desired disc for play in the remote CD changer. To advance to
a higher number disc, press the "CD+" button cs. To return to a
lower number disc, press the "CD-" button ct. The number of
the disc in play will be shown on the display panel.
cu FRONT PANEL RELEASE BUTTON
Thisbuttonisusedtoreleasethemechanismthatholdsthefront
panel to the chassis. To detach the front panel, press the button
so that the left side of the panel is released. Grasp the released
side and pull it off of the chassis.
Tore-attachthepanel,positiontherightsideofthepanelinplace
firstand then presstheleft sideofthepanel untilthemechanism
locks it into place.
dl THEFT-DETERRENT L.E.D.
Thetheft-deterrentLightEmittingDiode(L.E.D.)islocatedbehind
thefrontpanelandisaccessiblewhenthefrontpanelisremoved.
Theflashinglightservesasavisualwarningtothewould-bethief
that the unit has been disabled by removal of the front panel.
dm RESET BUTTON
A "RESET" button is located on the front of the chassis (front
panel must be removed to access the button). The "RESET"
circuitry is provided to protect the microprocessor circuitry and
should only be activated under the following circumstances as it
will erase the time and pre-set memories:
1.Upon initial installation after all wiring is completed.
2.After the position of the frequency step switch on the bottom
of the chassis has been changed.
3.If there is a malfunction of any of the switches on the unit,
pressingthe"RESET"buttonmayclearthesystemandreturn
to normal operation.
-8-

-9-
Engage right
side first
ATTACHING THE FRONT PANEL
Release Button
DETACHING THE FRONT PANELNOTES ON USE OF FRONT PANEL
1.Make surethefront panelisright-side-up when attachingitto thechassis
as it cannot be attached when up-side down.
2. Do not press very hard on the front panel when attaching it to the
chassis. No more than light to moderate pressure should be needed.
3. When attaching the front panel, make sure the right side is correctly
engaged before pressing the left side to lock it into position.
4. When taking the front panel with you, please use the supplied carrying
case to protect the panel from dirt and damage. Make sure there is no
dust or dirt on the electrical terminals on the back of the panel as this
could cause intermittent operation or other malfunctions.
NOTES ON USE OF REMOTE INPUT JACK
Theremoteinputjackprovidestheuseroptionofapplyinganexternalaudio
source to the radio.
The audio jack is compatible with most "Walkman" CD and cassette
players,oran MP3digitalaudioplayback unit. When the external source
isconnected,onlythatmediaisplayedbytheradio;nootherinputsources
(radio or CD) are operative.

SPECIFICATIONSSPECIFICATIONS
SPECIFICATIONSSPECIFICATIONS
SPECIFICATIONS
Size: 7" W x 2" H x 6-5/16" D
178 mm x 50 mm x 160 mm
Operating Voltage: 12 volts DC, negative ground
Output Power: 140 watts maximum
( 35 watts x 4 channels)
Output Wiring: Floating-ground type designed for 4 speaker use.
FrontandrearchannelsCANNOTbecombined(bridged) foruse
with 2 speakers.
RCA low-level outputs (rear channels).
Output Impedance: Compatible with 4 ohm speakers.
Low-Level Output: 2.0 volts (2,000 mv.)
Tuning Range: AM: 530 - 1,710 kHz. (10 kHz. step)
FM: 87.5 - 107.9 MHz. (200 kHz. step)
Sensitivity: < 70 uV
FM Stereo Separation: > 20 dB
CD Frequency Response: 20 - 20,000 Hz. +0 / -3 dB
CD Signal/Noise Ratio: >85 dB
CD Channel Separation: >65 dB
CD Distortion: 0.2%
*Specifications are subject to change without notice.
-10-

CD CHCD CH
CD CHCD CH
CD CHAA
AA
ANGER CONTRNGER CONTR
NGER CONTRNGER CONTR
NGER CONTROLOL
OLOL
OLSS
SS
S
Built into this radio are controls to operate an optional CD
changer. Please check with your Rampage/Audiovox car ste-
reo specialist or call 1-800-645-4994 for recommendations of
the models that will work with this radio.
Adjustment of the audio functions (volume, tone, balance, and
fader) for the CD changer operate in the same manner as they
do for radio play. The following controls will operate the CD
changer when it is installed and connected to this radio. Refer
to the owner’s manual included with the CD changer for instruc-
tions on the installation and correct loading and use of the CD
magazine.
dn CD CHANGER MODE SELECTOR (MODE)
During radio or CD play, press this button to select operation of
the CD changer as shown by CDC on the display panel. Disc
play will begin and the disc and track number will be shown on
the display panel. If a new magazine has been loaded into the
changer, play will begin from the first track of the first disc in the
magazine. If a magazine was already in the changer, play will
resume from the track on the disc previously in play.
do &dp DISC SELECT (CD+ & CD-)
These buttons are used to select the desired disc for play. To
advance to a higher number disc, press the CD+ button do. To
return to a lower number disc, press the CD- button dp. The
number of the disc in play will be shown on the display panel.
dq TRACK SELECT (+ / -)
The Track Select functions are used to quickly access the
beginning of a particular track. Each time the Forward Track
Select (+) in side of the button is pressed, the next higher
track number will be selected as shown on display panel. Simi-
larly, each time the Backward Track Select ( -) side of the
button is pressed, the next lowertrack number will be selected
as shown on the display panel.
dr CUE/REVIEW FUNCTIONS (+ / -)
High-speed audible search to any section of the disc can be
made by the Cue and Review functions. Press and hold the
Cue (+) side of the button to advance rapidly in the forward
direction (the disc play symbol will rotate foward on the display
panel) or the Review ( -) side of the button to advance rapidly
in the backward direction (the disc symbol will rotate backwards
on the display panel).
ds TRACK/DISC SCAN SELECTOR (SCN)
When the SCN button is pressed, the SCN indication will ap-
pearon thedisplay panel,and thefirst 10secondsof eachtrack
on the disc will be played in order. When a desired track is
reached, press the SCN button once and play of the selected
track will continue (SCN will disappear from the display panel).
The Track Scan mode will also be canceled by activating the
(Repeat or Random Play functions).
When the SCN button is pressed twice, theDISC and SCAN
indications will appear on the display panel and the first 10 sec-
ondsof the firsttrackon eachdiscinthe magazinewillbeplayed.
-11-

When a desired disc is reached, press the Scan button again
andplay ofthe selecteddiscwill continue( DISC andSCANwill
disappear from the display panel). The Disc Scan mode will
also be canceled by activating the (Repeat Play or Random
Play functions).
dt DISC/TRACK REPEAT PLAY (RPT)
When the Repeat button is pressed, the RPT indication will
appear on the display panel and play of the selected track will
be continually repeated until the Track Repeat mode is canceled
by pressing the Repeat button again or by activating the Scan ds
or Random Play du functions.
When the Repeat button is pressed twice the DISC and
RPT indications will appear on the display panel and play of the
selected disc will be continually repeated until the Disc Repeat
mode is canceled by pressing the Repeat button again or by
activating the Scan ds or Random Play du functions.
-12-
du DISC/TRACK RANDOM PLAY (RND)
When the Random button is pressed, the RND indication will
appear on the display panel and the tracks on the disc will be
played in a random, shuffled order. The Track Select button dp
will also select tracks in the shuffled order instead of the normal
progression. The Random Track mode can be canceled by
pressing the Random button again or by activating the Scan ds
or Repeat Play dt functions.
When the Random button is pressed again, the DISC and RND
indications will appear on the display panel and the discs in the
magazine will be played in a random, shuffled order, as well as
the tracks on each disc. After playing a track selected at random
from a disc in the magazine, the unit will select another disc at
random and play a randomly selected track on it. This will
continue until the Random Disc mode is canceled by pressing
the Random button again or by activating the Scan ds or
Repeat Play dt functions.
SETSET
SETSET
SETTT
TT
TING THE CLOCKING THE CLOCK
ING THE CLOCKING THE CLOCK
ING THE CLOCK
1. Turn the vehicle ignition and radio “on”.
2. Press the Time/Frequency Selector button co to display the time.
3. While the time is being displayed, press the Time /Frequency Selector button co together with the Manual Down Tuning button
(-) to adjust the hours or the Manual Up Tuning button + to adjust the minutes to the correct time.
4. Five seconds after the last hour or minute adjustment is made, the time will be set in the unit and normal operation can resume.

If a problem should develop while operating the CD player, an error code (ER-1, ER-2, ER-3, etc.) may appear on the display
panel. This can indicate a number of problems with the unit, including a mechanical error or an error in the microprocessor control
of the player. If an error code should appear, try ejecting and re-loading the disc into the player. While the disc is out of the unit,
make sure it is clean, undamaged, and loaded correctly (label surface up). You may also try activating the RESET button dm on the
unit, but this will also erase the time and pre-set memories.
If the suggested measures do not solve the problem, contact an approved warranty station near you for further assistance.
If a problem should develop while operating the CD changer, the following error codes may appear on the display panel.
ER-1: Indicates that there is no magazine loaded in the CD changer.
ER-2: Indicates a problem with the magazine eject function.
ER-3: Indicates an error in the disc loading function.
ER-4: Indicates an error in the disc un-loading function.
ER-5: Indicates an error in the magazine position.
ER-6: Indicates an error in the laser pick-up position.
ER-7: Indicates an error in the laser focus on the disc.
In any of the above situations, try ejecting the CD magazine from the changer and make sure the discs are clean, undamaged, and
loaded correctly (refer to the Owner’s Manual of the CD changer). Re-load the magazine and check for proper operation. You may
also try activating the RESET button dm on the unit, but this will also erase the time and pre-set memories.
If the suggested measures do not solve the problem, contact an approved warranty station near you for further assistance.
CD CHCD CH
CD CHCD CH
CD CHAA
AA
ANGER ERRNGER ERR
NGER ERRNGER ERR
NGER ERROR CODESOR CODES
OR CODESOR CODES
OR CODES
CD PLCD PL
CD PLCD PL
CD PLAA
AA
AYER ERRYER ERR
YER ERRYER ERR
YER ERROR CODESOR CODES
OR CODESOR CODES
OR CODES
-13-

lDo not attempt to open the unit chassis. There are no user
serviceable parts or adjustments inside.
lWhenthevehiclewarmsupduringcoldweatherorunderdamp
conditions, moisture may condense on the lens of the disc
player. Should this occur, the player will not operate properly
until the moisture has evaporated.
lThe unit is designed with a vibration dampening CD mechanism
to minimize interruption of disc play due to normal vibration in
amovingvehicle. Whendrivingon veryrough roads,however,
occasional sound skips may occur. This will not scratch or
damage the disc and normal play will resume when the rough
conditions cease.
HANDLING COMPACT DISCS
Dirt, dust, scratches, and warpage can cause skips in the
playback and deterioration of sound quality. Please follow these
guidelines to take care of your compact discs:
lUse only compact discs with the mark .
lFingerprints, dust, and dirt should be carefully wiped off the
disc’s playing surface (shiny side) with a soft cloth. Wipe in a
straight motion from the inside to the outside of the disc.
lNeverusechemicalssuchasrecordsprays,householdcleaners
or thinner to clean compact discs. Such chemicals can
irreparably damage the disc’s surface.
lDiscs should be kept in their storage cases when not in use.
lDo not expose discs to direct sunlight, high temperatures or
high humidity for extended periods.
lDonotstickpaper,tape,orlabelsonthediscsurfacesnorwrite
on them with any type of marker.
-14-
CARE AND MAINTENANCE
Theradiosectionofyournewsoundsystemdoesnotrequireany
maintenance. We recommend you keep this manual for
referenceonthe many features found in this unit as well as how
to set the clock.
The compact disc player section also requires no routine
maintenance, but proper understanding of its use and handling
will help you obtain maximum enjoyment of its capabilities. The
following points should be observed:
lWhen cleaning the interior of the vehicle, do not get water or
cleaning fluids on the unit.
lThe CD player is a precision instrument and will not operate
properlyinextremehotorcold. Incaseofsuchconditions,wait
until the interior temperature of the vehicle reaches a normal
temperature before using the player.
lIf the temperature inside the player gets too hot, a protective
circuitwillautomaticallystopplayofthedisc. Inthiscase,allow
the unit to cool off before operating the player again.
lNeverinsertanythingotherthana5"(12cm)compactdiscinto
the player as the mechanism can be damaged by foreign
objects.
lDo not attempt to use 3" (8 cm) CD-Single discs in this unit,
eitherwithorwithoutanadaptor,asdamagetotheplayerand/
or disc may occur. Such damage will not be covered by the
Warranty onthis product.
lWhen not using the disc player, always remove the compact
disc.Do notleavean ejecteddiscsitting inthe disc slotas this
can expose it to sunlight and other causes of damage.
COMPACT
DIGITAL AUDIO

AUDIOVOXCORPORATION(theCompany)warrantsto the original retail purchaser ofthisproductthatshouldthisproductorany part thereof,
under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such
defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill
of sale), specification of defect(s), transportation prepaid, to an approved warranty station or the Company at the address shown below.
The warranty period will be extended to 24 months from the date of original purchase if the product is installed by an authorized Prestige Audio
dealer.Toclaimwarrantyserviceduringthisextendedperiod,thebillofsalemustspecifythattheproductwasinstalledbyanauthorizedPrestige
Audio dealer.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred for
installation,removalorreinstallationoftheproduct,ortodamagetotapes,compactdiscs,speakers,accessories,orvehicleelectricalsystems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
ThisWarrantyisinlieu of allotherexpresswarrantiesorliabilities. ANY IMPLIED WARRANTIES, INCLUDINGANYIMPLIEDWARRANTYOF
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF
30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or
representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage
so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
12 / 24 MONTH LIMITED WARRANTY
Applies to automotive radios, radio/tape players, radio/CD players,
CD changers, power amplifiers, equalizers and accessories.
U.S.A. : AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 l1-800-645-4994
CANADA : CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA 128-5543

© 2000 Audiovox Corp., 150 Marcus Blvd., Hauppauge, N.Y.11788 Printed in China
128-5798