Audiovox PRO-9556C Pursuit Series User manual

128-8792
1 of 2
1
3 Channel Remote
Car Starter
FEATURES :
2 Three Button Programmable RF Transmitters
Three Channel Receiver (capable of accepting 4 transmitters)
External Superheterodyne Receiver Antenna w/PushButton Switch & LED
Keyless Entry Outputs (+) and (-)
On-Board Start Relay
On-Board Accessory Relay
On-Board Ignition 1 Relay
On-Board Ignition 2 Relay
Ignition 2 Relay Selectable On or Off During Cranking
On-Board Parking Light Relay
Ignition 3 / Shock By-Pass / GM VAT Output (relay required)
Tach Signal Learning Circuit
Two ( + ) and Two ( - ) Safety Shutdown Circuits
Alarm By-Pass Output
Accessory Outputs
(Pulse Before & After Start, During Crank & After Shut Down)
Selectable Steady or Flashing Parking Lights for Run Indication
Selectable 5, 10, 15, 20 Minute Run Time
Selectable 1 Sec., 3.5 Sec., or 1 Sec./Dbl 1 Sec. Door Lock Output Pulse
Car Finder Mode
Model PRO-9556C
Owner's Manual
KEYLESSENTRY
1. The Lock button on the transmitter is used to lock the vehicle's doors,
the Unlock button is used to unlock the vehicle's doors. To lock or unlock
the doors simply press and release the desired function button one time.
As a keyless entry unit, for your convenience, the parking lights will flash
once when the doors are locked and twice when the doors are un-
locked.
REMOTECARFINDER
The Lock or Unlock buttons are also used to access the car finder mode.
This feature is particularly useful in a crowded parking lot where finding
your car may be difficult. To access the car finder mode, while within
range of your car, simply press and hold either the lock or unlock button
of your transmitter for three seconds. The parking lights will begin to
flash making your vehicle more visible. The lights will stop automati-
cally after 30 seconds. If you wish to turn off the car finder mode prior
to the expiration of the 30 second timer, press and release either the lock
or unlock button of your transmitter one time
REMOTETRUNKRELEASE
If you have electric trunk release in your vehicle and the remote trunk release option was
added to your vehicle, simply press and hold the Key/Trunk button of your keychain
transmitter for 4 seconds or until the electric trunk of your vehicle opens.

128-8792
2 of 2
2
© 2010 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-8792
REMOTE STARTING THE VEHICLE
This unit will not start the vehicle if any one of the following situations exists:
The vehicle's hood lid is opened. The gear shift selector is not in Park.
The brake pedal is depressed. The safety control switch is in the Off position.
1. To start the vehicle, press and release the Key/Trunk button two times within 2 seconds.
The vehicle will start and remain running for the pre-programmed 5,10,15,20 minute run
cycle. As a visual indication, the parking lights will flash or remain on depending on the
setting by your installation center.
2. When you arrive at the vehicle, turn the ignition key to the ON position (not the spring
loaded start position), then step on the brake pedal to disengage the remote starter. The
vehicle will continue to run, but now on it's own power.
NOTE: The engine will stop running before the pre-programmed run cycle has expired if
you perform any one of the following functions:
Press and release Key/Trunk button on the keychain transmitter two times within 2
seconds.-Depress the brake pedal. - Open the vehicle's hood -Place the unit in
the safety control disabled mode.
PUSH-BUTTONLED RECEIVERVALET/OVERRIDE/SAFETYCONTROLSWITCH
The Push-Button LED switch located in the receiver allows you to temporarily disable the
remote starting function of the system. This recommended whenever the vehicle is being
serviced. To place the system in the service mode:
1) With the system disarmed/unlocked, and the ignition switch off Press and Hold the
Push-Button, found on the windsheild receiver, in.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED begins to flash two short flashes followed by one long flashes and contin-
ues this pattern until returned to normal mode of operation.
This puts the unit into the R/S Override mode indicating that the remote start is in the
service mode and will not start from RF or any other input Posse or otherwise.
To Exit R/S Override Mode
1) With the system disarmed, Press and Hold the Push-Button, found on the windsheild
receiver, in.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED turns off indicating that the R/S unit is fully functional one again.
PROGRAMMED TRANSMITTER NOTIFICATION (PTN)
Every time after Disarm when the ignition key is turned on, the unit's LED will report the
number of transmitters programmed into the system. This safety feature will alert you if an
unauthorized transmitter has been programmed into your vehicle's security system without
your knowledge. Typical from the factory, there will be a 2 flash, pause, repeated 3 times
indicating that two transmitters are programmed into the system. If you note additional
flashes, there may heve been an additional transmitter added without your knowledge or
authorization. If you notice a change in the transmitter LED report pattern, you can
correct this by looking up how to erase and reprogram your transmitters found in the
transmitter programming guide. This reprogram operation will erase all unauthorized or
unwanted transmitters.
FUNCTION SETTING CHART
To be completed by installer
Run Time _______Min
Door Lock Timer ______Sec
Lights Pulse Steady 