Audiovox PRO9555 User manual

3 Channel Remote
Car Starter
Model PRO-9555
Owner’sManual
FEATURES :
w2 Two Button Programmable RF Transmitters
wThree Channel Receiver (capable of accepting 4 transmitters)
w(+) & (-) Keyless Entry Outputs
wOn-Board Start Relay
wOn-Board Accessory Relay
wOn-Board Ignition 1 Relay
wOn-Board Ignition 2 Relay
wIgnition 2 Relay Selectable On or Off During Cranking
wOn-Board Parking Light Relay
wIgnition 3 / Shock By-Pass / GM VAT Output (relay required)
wTach Signal Learning Circuit
wTwo ( + ) and Two ( - ) Safety Shutdown Circuits
wAlarm By-Pass Output
wFactory Disarm Output Before Start And During Unlock
wSelectable Steady or Flashing Parking Lights for Run Indication
wSelectable 5, 10, 15, 20 Minute Run Time
wSelectable 1 Sec., 3.5 Sec., or 1 Sec./Dbl 1 Sec. Door Lock Output Pulse

KEYLESS ENTRY
1. The Lock/Unlock on the transmitter is used to lock and unlock the vehicle's doors. To lock
or unlock the doors simply press and release this button one time. As a keyless entry unit,
for your convenience, the parking lights will flash once when the doors are locked and
twice when the door are unlocked.
REMOTE CAR FINDER
The Lock/Unlock button is also used to access the car finder mode. This
feature is particularly useful in a crowded parking lot where finding your
car may be difficult. To access the car finder mode, while within range
of your car, simply press and hold the lock/unlock button of your transmit-
ter for three seconds. The parking lights will begin to flash making
your vehicle more visible. The lights will stop automatically after
30 seconds. If you wish to turn off the car finder mode prior to the
expiration of the 30 second timer, press and release the lock/unlock
button of your transmitter one time.
REMOTE STARTING THE VEHICLE
The unit will not start the vehicle if any one of the following situations exists;
-The vehicle's hood lid is opened.
-The gear shift selector is not in Park.
-The brake pedal is depressed.
-The safety control switch is in the Off position.
1. To start the vehicle, press and release the button with the key icon two times within 2
seconds. The vehicle will start and remain running for the pre-programmed 5,10, 15, 20
minute run cycle. As a visual indication, the parking lights will flash or remain on
depending on the setting by your installation center.
2. When you arrive at the vehicle, turn the ignition key to the "ON" position (not the spring
loaded start position), then step on the brake pedal to disengage the remote starter. The
vehicle will continue to run, but now on it's own power.
NOTE: The engine will stop running before the pre-programmed run cycle has expired if
you perform any one of the following functions;
-Press and release button #2 on the keychain transmitter two times within 2 seconds.
-Depress the brake pedal.
-Open the vehicle's hood.
-Move the safety control switch to the Off position.
NOTE: Consult Transmitter Programming Guide for information on the Optional
second vehicle control button "O".
SAFETY CONTROL SWITCH
The red handle control switch allows you to temporarily disable the remote starting function
of the system and moving this switch to the "Off" position is recommended whenever the
vehicle is being serviced. When the system is disabled, the remote door locks and optional
accessories will remain operational.
FUNCTION SETTING CHART
To be completed by installer
Run Time 5 Min. o10 Min. o15 Min. o20 Min. o
Door Lock Timer 1 Sec/1 Sec. o3.5 o1 Sec./Dbl. 1 Sec. o
Lights Pulse oSteady o
© 2001 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-6139